Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Drill Press with Laser Guide: What to Look For

A drill press with laser guide marks the drilling point so the bit lands where you aim: built-in laser, add-on crosshair and magnetic guide, compared on fit, power and visibility.

Drill Press with Laser Guide: What to Look For
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SKIL 6.2 Amp 10 In. 5-Speed Benchtop Drill Press with LaserSKIL 6.2 Amp 10 In. 5-Speed Benchtop Drill Press with Laser9.6/10View on Amazon
  2. 2WOODSKIL 8-Inch Benchtop Drill PressWOODSKIL 8-Inch Benchtop Drill Press9.5/10View on Amazon
  3. 3WEN 12-Inch Benchtop Drill PressWEN 12-Inch Benchtop Drill Press9.5/10View on Amazon

A drill press with laser guide puts a mark on the exact spot the bit will enter, so you line up the work once instead of creeping the table back and forth. The guide can be built into the press, added as a crosshair laser, or carried as a magnetic guide on a hand drill. This guide explains what each kind does, what to look for, and where each one falls short, using only the figures the listings state.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What a laser guide does

A laser guide marks the drilling point so the bit lands where you aim. On a drill press with a built-in laser, the mark comes from the machine itself: the listing for one 8 in benchtop press states a Class II laser with a max of 1mW, a 1W LED work light, 5 speeds from 620 to 3100 RPM, a 1/2 in chuck and an 8 in swing. An add-on crosshair laser mounts to any drill press and projects cross-hairs that stay on center at any table or work piece height; the Wixey listing states a class 3a laser with output less than 2.5MW, rugged steel construction, and 2 AA batteries, not included. A magnetic laser guide attaches to a hand drill chuck and projects laser circles onto the work surface while the drill spins, so it works away from the press. A center finder is a different tool: it locates the true center on round workpieces with a 3/8 in shank, and it projects no laser.

Drill press with laser guide: side by side

Drill press with built-in laser Add-on crosshair laser Magnetic laser guide
Laser Class II, max 1mW Class 3a, less than 2.5MW Green or red laser circles
Mounts to The drill press itself Any drill press A drill chuck, magnetically
Bit range stated 1/2 in chuck and drill capacity Not stated 2 to 4 in standard, 2 to 8 in extended, 1/2 in diameter max
Power 120V 2 AA batteries LR44 coin cells
Battery life stated Not stated Not stated About 2.5 hours green, up to 9 hours red
Table or angle Tilts 0–45° Cross-hairs stay on center at any table height Reads the surface at any angle
Outdoor use Not stated Not stated Not visible in sunlight or outdoors
Speeds stated 5 speeds, 620 to 3100 RPM Not stated Works while spinning at moderate-to-high speed

The green and red magnetic guides state different battery life figures, about 2.5 hours for green and up to 9 hours for red, so check the color you buy. Laser class is as the listing states it; follow the warnings printed on the guide and in the machine manual.

When a built-in laser guide is the better choice

  • One machine, no add-on. The laser and the LED work light are part of the press, so there is nothing to mount or align before the first hole.
  • Speed control on the same machine. The 8 in press lists 5 speeds from 620 to 3100 RPM, so the same press covers wood and metal work.
  • Angled work. The worktable tilts 0–45°, so the laser marks the spot while the table sits at an angle.
  • Bigger work. The press lists a 1/2 in chuck, an 8 in swing and a weight of 25.94 pounds, so it holds work a hand drill guide cannot.

Our best drill press guide compares presses for the shop, and our best drill press for metalworking guide covers presses for metal work.

When a magnetic laser guide is the better choice

  • No drill press. It magnetically attaches to the drill you already own in seconds, with no tools and no mods, so it works where a press cannot go.
  • Angled and sloped surfaces. It reads the surface itself and keeps the drill square at any angle, where a bubble level fails because it only knows gravity.
  • Bright workspaces. The green laser suits bright workspaces and dark surfaces where the red laser is harder to see.
  • Overhead work. One hand, no separate guide to hold and no bulky jig to clamp, so it is easy to control even overhead.

How to tell what a guide fits

Check the listing for these before you buy:

  • Bit length. The standard magnetic guide covers bits up to 4 in, and the extended model covers bits up to 8 in, both 1/2 in diameter max. For bits over 4 in, the extended model is required.
  • Drill type. It fits standard cordless drills and hammer drill drivers, but not rotary hammer (SDS / SDS-Plus) drills or hole saws. An impact or hex-shank driver needs the Chuck Alignment Guide, sold separately.
  • Shank. The center finder uses a 3/8 in shank, and the Fritzfurt portable drill guide (on Amazon) uses a 1/4 in hex shank.
  • Batteries. The crosshair laser uses 2 AA batteries, not included, and the magnetic guides use LR44 coin cells, included.

The crosshair laser listing states no bit range, so it leaves the fit to the press it mounts on. The portable guides state their own ranges: the WEN guide (on Amazon) takes bits from 1/16 in to 1/2 in, and the Fritzfurt guide takes bits from 3/64 in to 25/64 in, or 1 to 10 mm.

Laser color and visibility

Green and red are the two laser colors in these listings, and they trade visibility against battery life. The green laser suits bright workspaces and dark surfaces where the red laser is harder to see, and its battery lasts about 2.5 hours. The red laser gives up to 9 hours of battery life, and the listing points to it for longer runtime in low light. Neither color is visible in sunlight or outdoors: both magnetic guides are built for indoor, garage and workshop work. The crosshair laser listing states no color difference and no battery life, so judge it on its class 3a output of less than 2.5MW instead.

Can one guide cover both jobs?

Yes, in the shop: a drill press with a built-in laser covers bench work, and a magnetic guide covers work away from the press, including angled and overhead holes. The crosshair laser mounts to any drill press, so it stays with the press rather than the job. If you drill mostly on the bench, the press laser is enough; if you drill on installed work, the magnetic guide earns its place. The center finder covers a third job, round stock, that no laser guide in these listings handles.

Drill press safety. Wear eye and face protection, clamp the work, keep guards in place, and keep gloves away from rotating parts. A laser guide marks the spot, it does not hold the work, and it does not replace the manual for your machine.

For more options, see our metal fab tools guides.

FAQ for welders

Do I need a drill press to use a laser guide?

No. The magnetic guide attaches to the drill you already own, so it works with no drill press at all. The crosshair laser mounts to a drill press, and the built-in laser comes with the press.

Are laser guides visible outdoors?

No. The magnetic guides state they are not visible in sunlight or outdoors, and they are built for indoor, garage and workshop work. The crosshair laser listing states no outdoor use either.

How long does the battery last on a magnetic laser guide?

About 2.5 hours for the green version, and up to 9 hours for the red version. Both use LR44 coin cell batteries, included, and the red version is the one the listing points to for longer runtime in low light.

What bit sizes does a magnetic laser guide fit?

The standard model covers bits up to 4 in, and the extended model covers bits up to 8 in, both 1/2 in diameter max. For bits over 4 in, the extended model is required.

Does a laser guide replace a center finder?

No. A laser guide marks where the bit will enter, while the center finder locates the true center on round workpieces with a 3/8 in shank. They cover different jobs.

Related: drill press vs hand drill, best drill press, best drill press vise, and best drill press for metalworking.

More buying guides

Metal Fab Tools ·

Drill Press Safety: Tips for Safe Drilling

Drill press safety comes down to clamping the work, keeping hands clear of the chuck, and wearing eye protection, with a vise that holds…

Metal Fab Tools ·

Drill Press Speed Chart by Bit Size

A drill press speed chart matches bit size and material to spindle speed, and this guide shows how to read it and which bits…