Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Drill Press Guide for Hand Drill: Handheld Guides and Bench Stands

A drill press guide for a hand drill holds the drill square and steady, and this guide explains handheld guides, bench stands, angles, depth stops and collar sizes.

Drill Press Guide for Hand Drill: Handheld Guides and Bench Stands
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Strong Hand Tools PTTD634 Drill Press Clamp with Crank HandleStrong Hand Tools PTTD634 Drill Press Clamp with Crank Handle9.6/10View on Amazon
  2. 2BUCKTOOL 10-Inch Drill Press 6.2 Amp 3/4 HP Bench Drill PressBUCKTOOL 10-Inch Drill Press 6.2 Amp 3/4 HP Bench Drill Press9.7/10View on Amazon
  3. 3SKIL 6.2 Amp 10 In. 5-Speed Benchtop Drill Press with LaserSKIL 6.2 Amp 10 In. 5-Speed Benchtop Drill Press with Laser9.6/10View on Amazon

A bracket that needs a square hole, a hinge plate that has to line up, a hole through round tube: a drill press guide for hand drill work turns a hand drill into a small drill press. The guide holds the drill square to the work and controls the depth, so the bit starts where you want it and stops where you want it. This guide explains the handheld guides and bench stands that do that job, how to match a guide to a drill, and how to set angle and depth.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Drill press guide for hand drill: handheld guides and bench stands

Handheld guides and bench stands differ in where the drill sits. A handheld guide clamps to the drill and rides on the work, so you can take it to a wall, a board edge or a piece of round stock. A bench stand holds the drill on a column over a base, so the work comes to the drill and the stand controls the feed.

Side by side

Handheld drill guide Bench drill press stand Angle drill guide
What it is A guide that rides on the work and clamps to the drill A stand that holds the drill on a column over a base A guide with an angle dial for angled holes
Angled holes 45, 60, 75 and 90 degrees on the Milescraft guide 0 to 90 degrees on the AeKeatDa stand 0 to 60 degrees on the Cocowin guide
Depth control Depth stop for repeat holes Scale ring sets depth up to 60mm Dual tension springs give preset depth control
Round stock Self-centering base fits round stock up to 3 inches in diameter Vise or clamp holds the work on the base V-groove steadies round material
Collar fit Attaches to 3/8 inch and 1/2 inch drills Fits collars from 38 to 43mm Fits 1/2 inch chuck drills
Best for Holes on the job, on walls or on round stock Repeat holes at the bench Angled holes in wood, metal and composites

Angles and depths in the table come from the makers of the examples named there; check your own drill against the guide before ordering.

When a handheld guide is the better choice

  • Work that cannot move. Walls, board edges and round stock: the Milescraft guide drills on the edge of a board, on walls and on round stock up to 3 inches in diameter.
  • Angled holes on the job. The Milescraft guide locks at 45, 60, 75 and 90 degrees, and the Rockler guide (on Amazon) covers 0 to 60 degrees with a protractor scale.
  • Small shops. A handheld guide gives drill press precision without the bulk of a stationary drill press.
  • Repeat holes away from the bench. A depth stop lets you drill to the same depth again and again, which suits shelf pins.

See the drill press vs hand drill comparison for how a full press differs.

When a bench stand is the better choice

  • Repeat holes at the bench. A stand with a depth scale ring sets depth up to 60mm, so a run of holes comes out the same.
  • Steady feeding. A push-feed handle and a column keep the drill from wandering, and the Yoltckde stand (on Amazon) has a thickened 25mm iron column.
  • Small parts. A flat jaw vise or a flat plier holds small work while the stand holds the drill.
  • Taller work. The Yoltckde stand adjusts working height from 0 to 40cm, so the drill fits work of different heights.

The best drill press guide covers full presses for shops that outgrow a stand.

How to match the guide to your drill

Match the collar first. Bench stands clamp the collar of the drill, and the YMingweiAn and Greensen stands (on Amazon) fit collars from 38 to 43mm, while the Yoltckde stand fits 38 to 42mm and the AeKeatDa stand (on Amazon) fits collets from 25 to 40mm. The SYLQMERNDA stand fits (on Amazon) 38mm or 43mm collars. Measure the collar on your drill before ordering.

Match the chuck next. The Milescraft guide attaches to 3/8 inch and 1/2 inch drills and includes a 3/8 inch capacity chuck with a key, the Cocowin guide takes a 1/2 inch chuck, and the Rockler guide attaches to a 1/4 inch hex shank with a 1/2 inch chuck. The CertBuy guide fits 1/4 inch or 3/8 inch drills and clamps bits from 1.5 to 13mm. Check the fit that your guide uses, collar size for a bench stand and chuck size for a handheld guide, before ordering.

Setting depth and angle

Set the depth with the scale ring or the depth stop rod, then lock it. The YMingweiAn stand sets depth up to 60mm with a scale ring, the Yoltckde stand gives depth up to 60mm on its stroke scale, and the Greensen stand sets depth up to 60mm with an adjustable scale ring. A depth stop keeps the bit from going too deep.

Set the angle on the dial, then lock it. The Cocowin guide adjusts from 0 to 60 degrees on a laser-printed angle dial with a dual-locking mechanism, the CertBuy guide cuts angles from -45 to 45 degrees, and the AeKeatDa clamp rotates from 0 to 90 degrees. Check the angle after locking.

Can a hand drill replace a drill press?

For light work, yes. A guide or a stand gives a hand drill the square feed of a press for holes in wood, metal and composites, and the Yoltckde stand weighs 1.6kg, so it carries to a job site. For heavy work, no: the Greensen stand is made for light-duty household use and is not suitable for heavy-duty industrial drilling.

Drill press safety. Eye and face protection, clamp the work, no gloves near rotating parts, guards in place. Clamp the work to the base or hold it in a vise, and disconnect the drill from power before changing bits. See the OSHA machine guarding page and the drill press safety guide.

FAQ for welders

What does a drill press guide for a hand drill do?

It holds a hand drill square to the work and controls the feed and the depth, so holes come out straight and repeat.

What collar size fits a drill press stand?

It depends on the stand. The YMingweiAn and Greensen stands fit collars from 38 to 43mm, the Yoltckde stand fits 38 to 42mm, and the AeKeatDa stand fits collets from 25 to 40mm. Measure the collar on your drill before ordering.

Can a drill guide drill angled holes?

Yes. The Milescraft guide locks at 45, 60, 75 and 90 degrees, the Cocowin guide adjusts from 0 to 60 degrees, and the CertBuy guide cuts angles from -45 to 45 degrees. Lock the angle before drilling, and check it after locking.

How deep can a drill press stand drill?

The YMingweiAn, Yoltckde and Greensen stands set depth up to 60mm, with a scale ring, a stroke scale or an adjustable scale ring. Set the depth, lock it, and check the first hole.

Can I use a drill press guide on round stock?

Yes, with a guide made for it. The Milescraft guide has a self-centering base for round stock up to 3 inches in diameter, and the Cocowin guide has a V-groove for round material. Clamp the stock so it cannot roll while you drill.

Related: drill press vs hand drill, best drill press, best drill bit for drilling metal, and the metal fab tools hub.

More buying guides