Best Metal Shear Set (2026): 4 Picks for Sheet Metal
Aviation snips for sheet metal, compared on cut capacity, blade steel, leverage, handles and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMalco AV6 Offset Aviation Snips9.7/10View on Amazon - 2
Best 3-Piece SetWORKPRO 3-Piece Aviation Snips9.6/10View on Amazon - 3
Easiest CuttingDEKELIY 3-Piece Aviation Snips9.6/10View on Amazon - 4
Best 10 Inch SetTempest 3-Piece Aviation Snips9.5/10View on Amazon
A duct run needs a notch cut at the register, a gutter section needs trimming at the eave, and a patch panel needs a curve cut freehand. A metal shear set puts the right snip in your hand for each of those cuts, and the best metal shear set covers left, right and straight cuts without reaching for another tool. This guide compares the aviation snips on what each listing states: cut capacity, blade steel, leverage, handles and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Malco AV6 Offset Aviation Snips: Forged steel blades, an offset left-cut design, Power-Fit grips, and the only stated warranty here, Limited Lifetime. Check price on Amazon
- Best 3-Piece Set WORKPRO 3-Piece Aviation Snips: Left, right and straight snips in a compact 8 inch frame, rated at 18 gauge cold-rolled steel and 22 gauge stainless steel. Check price on Amazon
- Easiest Cutting DEKELIY 3-Piece Aviation Snips: Forged chrome vanadium blades with a stated 20% less effort, a spring-assisted latch, and non-slip rubber grips. Check price on Amazon
- Best 10 Inch Set Tempest 3-Piece Aviation Snips: Color-coded 10 inch snips for left, right and straight cuts, rated at 20 gauge cold-rolled steel and 22 gauge stainless steel. Check price on Amazon
The machines
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | Malco AV6 Offset Aviation Snips | 9.7/10 | Buy on Amazon |
| 2 | 3 Piece Aviation Tin Snips Set | 9.6/10 | Buy on Amazon |
| 3 | Dekeliy Aviation Tin Snips Set | 9.6/10 | Buy on Amazon |
| 4 | TEMPEST 3 Piece Aviation Snip Set | 9.5/10 | Buy on Amazon |

Malco AV6 Offset Aviation Snips
A single left-cut offset snip with forged steel blades, Power-Fit grips and a one-hand latch, rated at 18 gauge sheet metal and backed by a Limited Lifetime warranty.
Pros
- Forged steel blades rated at 18 gauge sheet metal
- Offset blades keep hands above the material for a clear line of sight
- Power-Fit grips with molded grooves and hand guards
- Limited Lifetime warranty, the only stated warranty here
Cons
- Left-cut only, so right-hand curves need another snip
- A single snip, not a set for left, right and straight cuts
- States 18 gauge sheet metal with no separate stainless steel figure
- A single red grip, with no color coding across cut directions

3 Piece Aviation Tin Snips Set
A 3-piece set of 8 inch aviation snips for left, right and straight cuts, rated at 18 gauge cold-rolled steel and 22 gauge stainless steel, with CR-V blades and a safety latch.
Pros
- 3 snips cover left, right and straight cuts
- Rated at 18 gauge cold-rolled steel and 22 gauge stainless steel
- Double-lever design with a compact pivot for large shearing force
- Serrated edge holds material and stops slipping
Cons
- No warranty term stated
- No item weight stated
- Cold-rolled capacity stops at 18 gauge, so thicker sheet needs another tool
- States a 10% effort saving, less than the 20% the DEKELIY states

Dekeliy Aviation Tin Snips Set
A 3-piece set of offset and straight aviation snips with forged chrome vanadium blades, rated at 18 gauge cold-rolled steel, with a spring-assisted latch and non-slip rubber grips.
Pros
- 3 snips cover left, right and straight cuts
- Forged chrome vanadium blades, austemper heat-treated
- States 20% less effort with a high-leverage design
- Spring-assisted latch for fast one-handed operation
Cons
- States 18 gauge cold-rolled steel with no stainless steel figure
- No warranty term stated
- The set is heavier than the single Malco snip
- Tight curves need the left or right offset snips, not the straight snip

TEMPEST 3 Piece Aviation Snip Set
A 3-piece set of 10 inch aviation snips with color-coded sleeve handles, rated at 20 gauge cold-rolled steel and 22 gauge stainless steel, with Cr-V serrated blades and a manual locking latch.
Pros
- 3 10 inch snips cover left, right and straight cuts
- Color-coded handles: red for left, yellow for straight, green for right
- Rated at 20 gauge cold-rolled steel and 22 gauge stainless steel
- Sleeve handles wipe clean and carry molded hang hooks
Cons
- 20 gauge cold-rolled capacity is the lowest stated here
- No item weight stated
- Manual latch with no spring assist stated
- States no effort saving, while the WORKPRO states 10% and the DEKELIY states 20%
Spec sheet comparison
| Model | Gear Score | Cut capacity | Set | Blade | Latch | Warranty |
|---|---|---|---|---|---|---|
| Malco AV6 Offset Aviation Snips | 9.7/10 | 18 ga sheet metal | 1 snip, left cut | Forged steel | One-hand side latch | Limited Lifetime |
| WORKPRO 3-Piece Aviation Snips | 9.6/10 | 18 ga cold-rolled, 22 ga stainless | 3 snips | CR-V, serrated | Safety lock | Not stated |
| DEKELIY 3-Piece Aviation Snips | 9.6/10 | 18 ga cold-rolled | 3 snips | Forged Cr-V, serrated | Spring-assisted latch | Not stated |
| Tempest 3-Piece Aviation Snips | 9.5/10 | 20 ga cold-rolled, 22 ga stainless | 3 snips | Cr-V, serrated | Manual locking latch | Not stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 22 November 2026.
How to pick the best metal shear set
Cut capacity in gauge
Capacity is the filter to check. The WORKPRO, DEKELIY and Malco listings state 18 gauge cold-rolled steel or sheet metal, while the Tempest states 20 gauge cold-rolled steel. The WORKPRO and Tempest also state 22 gauge stainless steel. The listings pair 18 gauge with 1.2 mm and 22 gauge with 0.8 mm, so the lower gauge is the thicker sheet. Match the capacity to the thickest sheet you cut, not the thinnest.
Left, right and straight cuts
A set earns its keep when it covers every direction. The WORKPRO, DEKELIY and Tempest sets each hold a left, a right and a straight snip. The Tempest maps its colors for you: red cuts left curves, yellow cuts straight lines and wide curves, and green cuts right curves. The Malco is a single left-cut snip, so it suits left curves, straight lines and tight curves, and leaves right curves to another snip.
Blades and leverage
Every listing here states serrated or forged blades, and the steel matters. The WORKPRO and Tempest use CR-V steel, the DEKELIY uses forged chrome vanadium steel with an austemper heat treatment, and the Malco uses hardened forged steel. Leverage decides how hard you squeeze: the WORKPRO uses a double-lever design with a compact pivot and states a 10% effort saving, the DEKELIY uses a high-leverage design and states 20% less effort, and the Malco uses compound action. Serrated edges hold the sheet firm so it does not slip mid-cut.
Handles, latches and storage
Handles decide how the snips feel after a long run of cuts. The WORKPRO has an ergonomic TRP handle with an outward arc and a hang hole. The DEKELIY has ergonomic non-slip rubber grips and a spring-assisted latch for one-handed operation. The Malco has Power-Fit grips with molded grooves and hand guards, plus a side latch that releases with a single hand. The Tempest has smooth sleeve handles that wipe clean, with a molded hang hook on each handle. Every pick here latches its blades closed for storage, which keeps the edges safe in the box.
Use as directed. Wear eye protection and cut-resistant gloves when you cut sheet metal, and clamp the work before you cut. Sheet edges stay sharp after the cut, so keep your free hand clear of the cut line and latch the blades closed before the snips go back in the box. See best cut resistant gloves for sheet metal for a matching pair.
FAQ for welders
What gauge sheet metal can aviation snips cut?
The WORKPRO, DEKELIY and Malco listings state 18 gauge cold-rolled steel or sheet metal, and the Tempest states 20 gauge cold-rolled steel. The WORKPRO and Tempest also state 22 gauge stainless steel. Check the gauge on the sheet you cut against the capacity the listing states, and stay inside it.
What do the red, yellow and green handles mean?
On the Tempest set, red cuts left curves, yellow cuts straight lines and wide curves, and green cuts right curves. The WORKPRO and DEKELIY sets also use colored handles so you can grab the right snip at a glance. The Malco has a single red grip, since it is a left-cut snip.
Can aviation snips cut stainless steel?
The WORKPRO and Tempest sets state 22 gauge stainless steel, so they cover light stainless work. The DEKELIY and Malco listings state cold-rolled steel and sheet metal, with no stainless figure stated. If stainless is your daily work, pick a set that states it.
Do I need a set or a single snip?
A set covers left, right and straight cuts, which suits ductwork, gutters and patch panels that mix curves and straight runs. A single snip suits a buyer who cuts a single direction all day: the Malco covers left curves, straight lines and tight curves, and leaves right curves to another snip.
How do I keep aviation snips cutting well?
Latch the blades closed when the snips are stored, so the cutting edges stay protected. The DEKELIY latch guards the edge in storage, and the Tempest latch keeps the blades closed when the snips are not in use. Wipe the Tempest sleeve handles clean after use, since they do not trap shavings the way textured grips can.
Related: sheet metal and tubing hub, best metal fabrication shears, aviation snips vs tin snips, best cordless metal shears, and the aluminum sheet metal gauge chart.
Scoring, line by line
Each set is scored on performance, build, value, safety and warranty, with performance carrying the most weight. No listing here states a safety certification, so safety adds nothing to any score here; the ranking comes from performance, build, value and warranty.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Malco AV6 Offset Aviation Snips | 9.7 | 29 | 22 | 19 | n/a | 4 |
| WORKPRO 3-Piece Aviation Snips | 9.6 | 30 | 21 | 21 | n/a | 0 |
| DEKELIY 3-Piece Aviation Snips | 9.6 | 29 | 21 | 20 | n/a | 0 |
| Tempest 3-Piece Aviation Snips | 9.5 | 27 | 20 | 20 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.




