Best Bench Vise Under $200 (2026): 4 Picks for the Home and Farm Shop
Four bench vises for the home and farm shop, compared on jaw width, jaw opening, throat depth, clamping force, swivel base and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallWilton 674U9.7/10View on Amazon - 2
Biggest CapacityForward CR80A9.7/10View on Amazon - 3
Best Clamp-On OptionMYTEC 2-In-1 Bench Vise9.6/10View on Amazon - 4
Most CompactLustriix BV29.4/10View on Amazon
A bracket that needs a bead run along a cracked frame rail, a length of pipe that needs a clean square cut, a flat bar that needs truing up before fit-up: all three jobs start the same way, with the work locked solid in a vise so both hands stay free for the torch, the grinder or the hammer. This guide compares the best bench vise under 200 for that kind of home and farm shop work, scoring the vises on jaw width, jaw opening, throat depth, clamping force, swivel base and warranty, from what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Wilton 674U: Lifetime warranty against manufacturing defects, dual lock-downs and a 360° swivel base. Check price on Amazon
- Biggest Capacity Forward CR80A: 8 inch jaw width, 9 inch jaw opening and 12,000 lbs clamping force in ductile iron. Check price on Amazon
- Best Clamp-On Option MYTEC 2-In-1 Bench Vise: Clamp-on or bolt-down mounting with a 270° swivel base and serrated pipe jaws. Check price on Amazon
- Most Compact Lustriix BV2: A compact cast iron vise with a 360° swivel base and an anvil for light work. Check price on Amazon
The machines

Wilton Utility Bench Vise, 4-1/2" Jaw Width
A utility bench vise with a 4-1/2 inch jaw width, a 4 inch jaw opening, dual lock-downs and a lifetime warranty against manufacturing defects.
Pros
- Lifetime warranty against manufacturing defects
- Replaceable hardened steel jaws with a serrated pattern
- Dual lock-downs and a 360° swivel base
- Built-in pipe jaws with a 1/8 to 1-1/2 inch capacity
Cons
- No clamping force figure stated in the listing
- Jaw width of 4-1/2 inches is narrower than the Forward and MYTEC picks
- Pipe jaw capacity tops out at 1-1/2 inches
- Anvil size is not stated in the listing

Forward CR80A 8 Inch Bench Vise Heavy Duty
An 8 inch ductile iron bench vise with a 9 inch jaw opening, a 4.1 inch throat depth and a stated 12,000 lbs clamping force.
Pros
- 12,000 lbs clamping force, the highest stated here
- 8 inch jaw width with a 9 inch maximum jaw opening
- Ductile iron rated at 60,000 PSI
- Replaceable flat jaws plus built-in pipe jaws for 1/2 to 3 1/2 inch pipe
Cons
- No warranty term stated in the listing
- Largest footprint here at 19.3 x 8.4 x 9.7 inches
- Swivel base turns 210°, less than the 360° bases here
- No item weight stated in the listing

MYTEC 2-In-1 Bench Vise Heavy Duty for Workbench
A 6 inch cast steel bench vise with clamp-on or bolt-down mounting, a 270° swivel base and serrated pipe and flat jaws.
Pros
- Two mounting options: clamp-on base or bolt-down
- 270° swivel base for clamping at an angle
- Serrated pipe jaws and flat jaws in hardened steel
- Polished flat anvil for straightening small work
Cons
- No warranty term stated in the listing
- Clamping force of 3300 lbs is well below the Forward pick
- Throat depth of 2.2 inches is the shallowest stated here
- Clamp base fits workbench thicknesses up to 2.1 inches

Heavy Duty 2-in-1 Bench Vise, 3.2" Jaw Width
A compact cast iron bench vise with clamp-on or bolt-down mounting, a 360° swivel base and an anvil for light work.
Pros
- Two mounting options: clamp-on or bolt-down
- 360° swivel base for multi-angle work
- Textured non-slip jaws hold wood, plastic, metal and pipe
- Anvil for light hammering, bending and straightening
Cons
- Jaw width stated two ways: 3.2 inches in the title, 3.3 inches in the bullets
- Maximum jaw opening of 2.5 inches is the smallest here
- No warranty term stated in the listing
- No clamping force figure stated in the listing
Other welders and gear to compare
Forward 1740 4 Inch Bench Vise Heavy Duty with Anvil and 360°Check price on Amazon
MYTEC 2-In-1 Bench Vise Heavy Duty for WorkbenchCheck price on Amazon
MYTEC Bench Vise or Table ViseCheck price on Amazon
MYTEC 2-In-1 Work Bench ViseCheck price on Amazon
Forward DT08125A 5 Inch Heavy Duty Bench Vise with 360°SwivelCheck price on Amazon
WORKPRO Bench ViseCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Jaw width | Max jaw opening | Throat depth | Clamping force | Swivel base | Warranty |
|---|---|---|---|---|---|---|---|
| Wilton 674U | 9.7/10 | 4-1/2 in | 4 in | 2-5/8 in | Not stated | 360° | Lifetime |
| Forward CR80A | 9.7/10 | 8 in | 9 in | 4.1 in | 12,000 lbs | 210° | Not stated |
| MYTEC 2-In-1 Bench Vise | 9.6/10 | 6 in | 4.3 in | 2.2 in | 3300 lbs | 270° | Not stated |
| Lustriix BV2 | 9.4/10 | 3.2 in (title) | 2.5 in | Not stated | Not stated | 360° | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (28 October 2026). Where a listing states a figure in different places, the table shows each version.
Buying guide: picking the best bench vise under 200
Jaw width and jaw opening
Jaw width sets how wide a workpiece the vise grips across its face, and jaw opening sets how thick a section it can swallow. The Forward pick pairs an 8 inch jaw width with a 9 inch maximum jaw opening, the widest combination here, while the Wilton pick pairs a 4-1/2 inch jaw width with a 4 inch jaw opening. The MYTEC pick sits between them at a 6 inch jaw width and a 4.3 inch maximum opening. Match the opening to the thickest section on the bench, not to the widest flat bar in the rack.
Throat depth
Throat depth is the reach from the jaw face to the screw, and it decides how far into a plate or bracket the vise can grip. The Forward listing states 4.1 inches of throat depth, the deepest figure here, against 2-5/8 inches for the Wilton pick and 2.2 inches for the MYTEC pick. The Lustriix listing states no throat depth. For brackets and gussets that need gripping well back from the edge, the deeper throat earns its keep.
Swivel base and lock-downs
A swivel base lets the vise turn to the angle the weld or cut wants instead of forcing the work around. The Wilton and Lustriix picks turn 360°, the MYTEC pick turns 270°, and the Forward pick turns 210°. The Wilton pick adds dual lock-downs, which matter once the base is set: a base that creeps under a hammer blow or a long bead undoes the fit-up it was holding.
Jaws and anvil
Flat jaws hold plate and bar, pipe jaws hold round stock without crushing it out of round, and an anvil gives a flat spot for straightening and light hammering. Every pick here lists an anvil and a way to grip pipe. The Forward pick states pipe jaws for 1/2 to 3 1/2 inch pipe, and the Wilton pick states a pipe jaw capacity of 1/8 to 1-1/2 inches. Replaceable jaws matter over time: the Forward and Wilton listings both state replaceable flat jaws, so a chewed-up jaw face is a part swap rather than a new vise.
Mounting and warranty
A vise that moves is a vise that fights the work. The MYTEC and Lustriix picks offer clamp-on or bolt-down mounting, so a shared table gets a vise without drilled holes, while a permanent bench gets bolts. Only the Wilton pick states a warranty term, a lifetime warranty against manufacturing defects. The other listings state no warranty term, so the purchase rests on the listing specs alone.
Before You Strike an Arc
- Check the jaw faces on arrival: the listing specs are the baseline, and a jaw face that arrives nicked or loose should go back before it marks work.
- Match the mount to the bench: clamp-on bases need a bench edge inside the stated clamping range, and bolt-down bases need holes that clear the bench frame.
- Set the swivel base angle before clamping, then lock it down and give the work a firm pull by hand before striking an arc.
- Keep pipe work in the pipe jaws and flat work in the flat jaws; round stock in flat jaws rolls under load.
- Confirm the warranty in writing on arrival, since only the Wilton listing here states a term.
FAQ for welders
What jaw width does a home shop vise need?
It depends on the work on the bench. The picks here run from a 3.2 inch jaw width in the Lustriix title to an 8 inch jaw width on the Forward pick, with the Wilton pick at 4-1/2 inches and the MYTEC pick at 6 inches. The Lustriix title states 3.2 inches and its bullets state 3.3 inches. Wide jaws spread clamping pressure across plate and bar, while a narrower vise suits small brackets and pipe work.
How much clamping force does a bench vise need?
The Forward pick states 12,000 lbs and the MYTEC pick states 3300 lbs, while the Wilton and Lustriix listings state no clamping force. For grinding, cutting and tapping on a farm or home shop bench, a stated figure lets the buyer compare directly instead of guessing from jaw size alone.
Is a swivel base worth having on a bench vise?
For welding and fabrication work, a swivel base turns the work to the angle the joint wants. The Wilton and Lustriix picks turn 360°, the MYTEC pick turns 270°, and the Forward pick turns 210°. A fixed base holds a single angle, so every angled joint means re-clamping the work instead of turning the vise.
Can a bench vise hold pipe as well as flat bar?
Yes, when the listing states pipe jaws. The Forward pick lists built-in pipe jaws for 1/2 to 3 1/2 inch pipe, the Wilton pick lists built-in pipe jaws with a 1/8 to 1-1/2 inch capacity, and the MYTEC pick lists serrated pipe jaws alongside flat jaws. The Lustriix pick lists textured jaws that hold pipe as well as wood, plastic and metal. Flat jaws alone can let round stock roll, so pipe jaws are the feature to check.
What does a lifetime vise warranty cover?
On the Wilton pick, the listing states a lifetime warranty against manufacturing defects. That wording covers defects in how the vise was made, not wear from use or damage on the job. Read the warranty text on the listing before buying, since the other picks here state no warranty term at all.
Related: best bench vise for metal work, best heavy duty bench vise, best clamp-on bench vise, bench vise vs C clamp, ductile iron vs cast iron bench vise and swivel vs fixed welding vise.
Scoring, line by line
Each vise is scored on performance, build, value, safety listing and warranty. A spec the listing does not publish scores nothing, and a warranty scores only when the listing states a term.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Wilton 674U | 9.7 | 28 | 21 | 20 | n/a | 5 |
| Forward CR80A | 9.7 | 33 | 24 | 22 | n/a | 0 |
| MYTEC 2-In-1 Bench Vise | 9.6 | 28 | 20 | 21 | n/a | 0 |
| Lustriix BV2 | 9.4 | 24 | 18 | 20 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




