Best Bench Vise for Home Use (2026): 5 Picks Compared
Five bench vises for home use compared on jaw width, opening, throat, swivel, weight and warranty, from a 6-1/2 inch Wilton to a clamp-on 3 inch vise.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallWilton Utility 676U9.8/10View on Amazon - 2
Best General PurposeWilton General Purpose 5 in9.7/10View on Amazon - 3
Biggest JawVEVOR Heavy Duty 8 in9.7/10View on Amazon - 4
Most PortableVEVOR Portable 4.5 in9.5/10View on Amazon - 5
Best Clamp-OnICOOCKIT Clamp-On 3 in9.4/10View on Amazon
A vise holds the work still while you cut, drill, file or weld it, and a home shop vise has to do that job without eating the whole bench. This guide compares five vises for the best bench vise for home use, judged only on what each maker publishes: jaw width, opening, throat, swivel, weight and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Wilton Utility 676U: 6-1/2 inch jaws, pipe jaws to 2 inches, 360 degree swivel and a lifetime warranty. Check price on Amazon
- Best General Purpose Wilton General Purpose 5 in: 5 inch jaw, 30,000 PSI gray cast iron, 120 degree swivel and a lifetime warranty. Check price on Amazon
- Biggest Jaw VEVOR Heavy Duty 8 in: 8 inch jaw, 8 inch opening, 5,620 lbs of clamping force and dual anvils. Check price on Amazon
- Most Portable VEVOR Portable 4.5 in: 4.5 inch jaw, 270 degree base and a labor-saving handle at 13.45 lb. Check price on Amazon
- Best Clamp-On ICOOCKIT Clamp-On 3 in: 3.2 inch jaw, 360 degree swivel and a clamp-on base at 3.8 lb. Check price on Amazon
The machines

Wilton Utility 6-1/2" Bench & Pipe Vise
A 6-1/2 inch bench and pipe vise with a 4 inch throat, built-in pipe jaws and a 360 degree swivel base, backed by a lifetime warranty.
Pros
- 6-1/2 inch jaws with a 6 inch opening and a 4 inch throat
- Built-in pipe jaws hold pipe and round stock from 1/4 inch to 2 inches
- 30,000 PSI gray cast iron body with a 60,000 PSI ductile iron base
- Lifetime warranty with replacement parts available
Cons
- 39.7 lb, heavy to move around the shop
- Not a press, and the handle is designed to bend under excessive force
- Mounting needs four 7/16-inch bolts on a 7-1/2-inch bolt circle
- Jaw size suits larger work, less handy for small parts

Wilton General Purpose Bench Vise, 5" Jaw Width
A 5 inch general purpose bench vise in 30,000 PSI gray cast iron, with a 120 degree swivel base, a large anvil and a lifetime warranty.
Pros
- 5 inch jaw with a 4 inch opening and a 2-1/2 inch throat
- 30,000 PSI gray cast iron body
- Swivel base rotates 120 degrees and has double lockdowns
- Hardened steel replaceable jaw inserts, machine serrated
Cons
- 120 degree swivel, less than the 360 degree bases here
- 5 inch jaw is smaller than the 6-1/2 and 8 inch vises here
- 27.0 lb for a 5 inch vise
- Sized for general purpose and light-duty use, not heavy fabrication

VEVOR Heavy Duty Bench Vise, 8" Jaw Width
An 8 inch ductile iron bench vise with 5,620 lbs of clamping force, dual anvil surfaces and a 360 degree locking swivel base.
Pros
- 8 inch jaw with an 8 inch opening and 2.95 inch throat
- 60,000 PSI ductile iron resists deformation and cracking
- 5,620 lbs of clamping force
- Dual anvil work surfaces and a quick-release lever
Cons
- No warranty term is stated
- 40.79 lb, the heaviest vise here
- 16.93 inch footprint needs a sturdy bench
- No built-in pipe jaws for round stock

VEVOR Bench Vise, 4.5 Inch
A portable 4.5 inch cast iron bench vise with anti-slip textured jaws, a 270 degree rotating base and a labor-saving handle.
Pros
- 4.5 inch jaw width for a wide clamping range
- 270 degree rotating base adjusts the clamping angle
- Anti-slip textured jaws grip material tightly
- Portable, with a labor-saving handle and quick installation
Cons
- No warranty term is stated
- 4.5 inch jaw suits smaller work than the 6-1/2 and 8 inch vises
- Cast iron body, not the ductile iron of the heavy duty VEVOR
- 270 degree swivel, less than the 360 degree bases here

Bench Vise 3 Inch, Table Vise with Built-In Anvil
A 3.2 inch clamp-on table vise with a built-in anvil and a 360 degree swivel base, made from cast iron for light-duty work.
Pros
- 3.2 inch jaw width with a 2.5 inch maximum opening
- Clamp-on base attaches to desktop, workbench or countertop edges
- 360 degree swivel base adjusts to any working angle
- 3.8 lb, the lowest weight here
Cons
- 3.2 inch jaw suits small work only
- Light-duty use only, not heavy fabrication
- Clamp-on base, not a bolt-down mount
- Base clamp range tops out at 3.2 inches
Other welders and gear to compare
VEVOR Bench ViseCheck price on Amazon
Heavy Duty Bench Vise 4“ Jaw Width and OpeningCheck price on Amazon
WORKPRO Bench ViseCheck price on Amazon
Dual-Purpose Combined Universal Vise 3.3" with 360° SwivelCheck price on Amazon
Table Vise or Bench Vise 3.2 InchCheck price on Amazon
Spec sheet comparison
| Vise | Gear Score | Jaw width | Max opening | Throat | Swivel base | Weight | Warranty |
|---|---|---|---|---|---|---|---|
| Wilton Utility 676U | 9.8/10 | 6-1/2 in | 6 in | 4 in | 360° | 39.7 lb | Lifetime |
| Wilton General Purpose 5 in | 9.7/10 | 5 in | 4 in | 2-1/2 in | 120° | 27.0 lb | Lifetime |
| VEVOR Heavy Duty 8 in | 9.7/10 | 8 in | 8 in | 2.95 in | 360° | 40.79 lb | Not stated |
| VEVOR Portable 4.5 in | 9.5/10 | 4.5 in | Not stated | Not stated | 270° | 13.45 lb | Not stated |
| ICOOCKIT Clamp-On 3 in | 9.4/10 | 3.2 in | 2.5 in | Not stated | 360° | 3.8 lb | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 19 November 2026.
Buying guide: how to choose the best bench vise for home use
Jaw width and opening
Jaw width sets the widest stock the vise holds flat. The VEVOR 8 inch vise opens to 8 inches, the Wilton 676U to 6 inches, the Wilton 5 inch to 4 inches and the ICOOCKIT to 2.5 inches. Match the opening to the stock you hold most, and remember the throat depth too: 4 inches on the 676U, 2.95 inches on the VEVOR 8 inch and 2-1/2 inches on the Wilton 5 inch. The VEVOR 4.5 inch lists a 4.5 inch jaw width without an opening figure, so check it against your stock before ordering.
Swivel base and lockdowns
A swivel base lets you turn the work to the angle you need. The Wilton 676U, the VEVOR 8 inch and the ICOOCKIT swivel a full 360 degrees, the VEVOR 4.5 inch turns 270 degrees and the Wilton 5 inch turns 120 degrees. The Wilton 5 inch and the 676U both lock with double lockdowns, so the base stays put once you set the angle. Check that the lockdowns are tight before you lean on the work.
Bolt-down or clamp-on
The Wilton 676U mounts through four holes with 7/16-inch bolts on a 7-1/2-inch bolt circle, and the VEVOR 8 inch comes with screws and nuts for setup in three steps. The ICOOCKIT clamps onto a desktop, workbench or countertop edge with a base clamp range up to 3.2 inches, which suits a bench you cannot drill into. A bolt-down mount suits heavy work that pulls on the vise, while a clamp-on mount moves between benches.
Pipe jaws and anvils
Only the Wilton 676U has built-in pipe jaws, holding pipe and round stock from 1/4 inch to 2 inches. Four vises here have an anvil surface: the Wilton 5 inch, the Wilton 676U, the VEVOR 8 inch with dual anvil surfaces, and the ICOOCKIT with a built-in anvil. If you shape or straighten stock on the vise, an anvil surface matters; if you only hold flat stock, it does not.
Weight and bench space
Weights here run from 3.8 lb for the ICOOCKIT to 40.79 lb for the VEVOR 8 inch, with the Wilton 676U at 39.7 lb, the Wilton 5 inch at 27.0 lb and the VEVOR 4.5 inch at 13.45 lb. A heavy vise stays put under load, but it also stays where you bolt it. Check the footprint too: the VEVOR 8 inch measures 16.93 by 7.95 by 7.87 inches and the 676U measures 18.1 by 9.4 by 10.2 inches, against 9.25 by 4.72 by 5.91 inches for the VEVOR 4.5 inch.
Use as directed. Clamp the work firmly before you cut, drill or grind, and keep hands clear of the jaws while you tighten them. Never use the Wilton 676U as a press, and never put a hammer, pipe extension or cheater bar on its handle. See the OSHA welding overview and our Safety Disclaimer.
Before You Strike an Arc
- Check the mounting before first use: the Wilton 676U mounts through four holes with 7/16-inch bolts on a 7-1/2-inch bolt circle, the VEVOR 8 inch comes with screws and nuts, and the ICOOCKIT clamps onto edges up to 3.2 inches.
- Check the jaw opening against your stock: 6 inches on the 676U, 8 inches on the VEVOR 8 inch, 4 inches on the Wilton 5 inch and 2.5 inches on the ICOOCKIT.
- Check the swivel base lockdowns before work: the Wilton 5 inch and the 676U lock with double lockdowns.
- Never use the 676U as a press, and never put a hammer, pipe extension or cheater bar on its handle, as the maker warns.
FAQ for welders
What size bench vise do I need for home use?
Match the jaw opening to your stock. The VEVOR 8 inch opens to 8 inches, the Wilton 676U to 6 inches, the Wilton 5 inch to 4 inches and the ICOOCKIT to 2.5 inches. For general home shop work, the 5 inch Wilton and the 6-1/2 inch 676U sit in the middle of this group.
What is the difference between cast iron and ductile iron?
Both are iron castings, but the listings here give different strength figures: the Wilton 5 inch and the 676U body are 30,000 PSI gray cast iron, while the VEVOR 8 inch is 60,000 PSI ductile iron and the 676U base is 60,000 PSI ductile iron. Ductile iron resists cracking better under heavy clamping, per the VEVOR listing.
Do I need pipe jaws on a bench vise?
Only if you hold round stock. The Wilton 676U is the only vise here with built-in pipe jaws, holding pipe and round stock from 1/4 inch to 2 inches. If you only hold flat stock, a plain serrated jaw does the job.
Can I mount a bench vise without drilling?
Yes, with a clamp-on vise. The ICOOCKIT clamps onto desktop, workbench or countertop edges with a base clamp range up to 3.2 inches. The Wilton 676U bolts through four holes, and the VEVOR 8 inch comes with screws and nuts for setup.
Which bench vise has a lifetime warranty?
Two here do: the Wilton 5 inch general purpose vise and the Wilton Utility 676U, both backed by the Wilton lifetime warranty against manufacturing defects.
Related: best bench vise for metal work, best welding vise for home shop, bench vise vs welding vise, and the welding tables and carts hub. Also see our clamp on vs bolt down bench vise. Also see our ductile iron vs cast iron bench vise. Also see our best bench vise under 50.
Scoring, line by line
Each vise is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Bench vises have no electrical safety listing to state, so every vise here scores zero on that criterion; the ranking comes from the other four. The two Wilton vises earn warranty points for their lifetime terms, and the rest score zero there because no term is stated.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Wilton Utility 676U | 9.8 | 32 | 22 | 21 | n/a | 4 |
| Wilton General Purpose 5 in | 9.7 | 30 | 21 | 21 | n/a | 4 |
| VEVOR Heavy Duty 8 in | 9.7 | 33 | 24 | 21 | n/a | 0 |
| VEVOR Portable 4.5 in | 9.5 | 27 | 19 | 20 | n/a | 0 |
| ICOOCKIT Clamp-On 3 in | 9.4 | 24 | 18 | 19 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




