Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

0.8 Mm vs 1.0 Mm Mig Wire: Which One Should You Buy?

Two flux core wires compared by stated diameter, gas needs and spool details, with a side-tag mismatch flagged in both listings.

0.8 Mm vs 1.0 Mm Mig Wire: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Flux Core Welding Wire .030Flux Core Welding Wire .0309.6/10View on Amazon
  2. 2E71T-GS 0.035 Inch (1.0 MM)E71T-GS 0.035 Inch (1.0 MM)9.5/10View on Amazon

This guide covers 0.8 mm vs 1.0 mm mig wire. Verdict. Pick the Rumvita example only if you plan to follow its listing, which says to use it with a CO2 or CO2/Argon mix supply, and pick the ALL-CARB example for self-shielded work where no shielding gas supply is available. Read the stated diameters before buying either, because the side labels in this comparison do not match the diameters the listings state.

A repair on thin-gauge steel in a drafty shop and a small fabrication job on a bench both start with the same question: which wire diameter suits the metal in front of the welder. This comparison puts the 0.8 mm vs 1.0 mm mig wire choice against two flux core listings, whose gas statements differ, on what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The two wires

Flux Core Welding Wire .030

Flux Core Welding Wire .030

Rumvita9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An E71T-GS flux core wire at .030 inches (0.8 mm) on a 10 pound ABS plastic spool, listed for use with a CO2 or CO2/Argon mix gas supply, with a low-splatter claim.

Pros

  • Used with 100% CO2 or CO2/Argon mix shielding gas
  • Low splatter with a smoother weld bead claimed
  • Single or multi-pass welds on mild carbon steel
  • Strong ABS plastic spool at 10 pounds

Cons

  • Requires a 100% CO2 or CO2/Argon mix gas supply
  • Side label says 1.0 mm while the listing states 0.8 mm
  • No warranty term is stated
  • No CSA, UL or ETL listing is stated
E71T-GS 0.035 Inch (1.0 MM)

E71T-GS 0.035 Inch (1.0 MM)

ALL-CARB9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A self-shielded E71T-GS flux core wire at 0.035 inches (1.0 mm) on a 10 pound spool, needing no welding gases.

Pros

  • Self-shielded, no welding gases required
  • Single-pass fillet and lap welding stated
  • Single or multi-pass welds on thin-gauge mild or galvanized steel
  • Wrapped in vacuum-sealed aluminum foil

Cons

  • Side label says 0.8 mm while the listing states 1.0 mm
  • No warranty term is stated
  • No CSA, UL or ETL listing is stated
  • No duty cycle is stated in the listing data

Other welders and gear to compare

Side by side

Rumvita E71T-GS ALL-CARB E71T-GS Note
Gear Score 56 55 Raw totals
Comparison side 1.0 mm side 0.8 mm side Side labels do not match stated diameters
Stated diameter .030 inches (0.8 mm) 0.035 inches (1.0 mm) Buy by the stated diameter
Shielding 100% CO2 or CO2/Argon mix Self-shielded, no gas required Gas supply decides this row
Spool weight 10 pounds 10 pounds No difference stated
Spool ABS plastic spool Vacuum-sealed aluminum foil As stated in each listing
Warranty Not stated Not stated No term in either listing

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 28 October 2026. Neither listing states a CSA, UL or ETL listing, a duty cycle, or a warranty term.

0.8 mm vs 1.0 mm mig wire: gas claims in the listings

The gas statements differ, but they are not a clean gas-shielded versus gasless split. The Rumvita listing says its E71T-GS wire is used with 100% CO2 or a CO2/Argon mix shielding gas, and claims low splatter with a smoother weld bead and little to zero post-weld cleanup, even though E71T-GS is a self-shielded designation and its spec table lists the wire form as Solid, Single-Strand while its title calls it flux core wire. The ALL-CARB listing states its wire is self-shielded, with no welding gases required, and lists single-pass fillet and lap welding among its uses. On the listings as written, a welder without a gas supply has only the ALL-CARB option here, while a welder with a gas supply can weigh the Rumvita low-splatter claim against the ALL-CARB gasless convenience.

The diameter mismatch

Read this part before the spool labels. The Rumvita listing states a diameter of .030 inches (0.8 mm), yet it sits on the 1.0 mm side of this comparison. The ALL-CARB listing states a diameter of 0.035 inches (1.0 mm), yet it sits on the 0.8 mm side. Neither listing states a second diameter, so the stated diameter in each listing is the figure to trust, not the side label. Buy by the diameter printed for the spool, and check it again on arrival, since a side label that disagrees with the listing is a reason to pause, not a reason to assume the listing is wrong.

Spool, weight and build

Both listings state a 10 pound spool, so spool weight does not separate them. The Rumvita spool is a strong ABS plastic spool, per its title, with dimensions of 8.27 x 8.11 x 2.4 inches in its spec table. The ALL-CARB wire is wrapped in vacuum-sealed aluminum foil, per its bullets, with package dimensions of 8.23 x 8.07 x 2.44 inches. The Rumvita listing also states higher levels of manganese and silicon than other standard grades of MIG wire, while the ALL-CARB listing names base materials including ASTM A36 and galvanized steel. Neither listing states a warranty term, a duty cycle, or a CSA, UL or ETL listing.

Choose the Rumvita E71T-GS if

  • You already run 100% CO2 or a CO2/Argon mix shielding gas.
  • You want the low-splatter, smoother-bead claim in the listing.
  • You weld mild carbon steel in single or multi-pass welds, per the listing.
  • You want an ABS plastic spool at 10 pounds.

Choose the ALL-CARB E71T-GS if

  • You want self-shielded wire with no welding gases required.
  • Your work is single-pass fillet and lap welding on thin-gauge steel.
  • You want wire wrapped in vacuum-sealed aluminum foil.
  • You weld light structural, machinery part, prefab or general fabrication work named in the listing.

Before You Strike an Arc

Before you strike an arc. Wear a helmet with the right shade for the process and amperage, safety glasses underneath, leather gloves and flame resistant clothing. Weld with good ventilation, clear anything flammable from the area, and keep an extinguisher close. Check the gas supply and connections on the Rumvita wire, and check the spool diameter on arrival for both wires. See the OSHA welding overview and our Safety Disclaimer.

FAQ for welders

Which wire needs shielding gas?

The Rumvita wire is used with 100% CO2 or a CO2/Argon mix shielding gas, per its listing. The ALL-CARB wire is self-shielded, with no welding gases required, per its listing.

What diameters do the two listings actually state?

The Rumvita listing states .030 inches (0.8 mm), and the ALL-CARB listing states 0.035 inches (1.0 mm). The side labels in this comparison run the other way, so buy by the stated diameter, not the side label.

How heavy is each spool?

Both listings state a 10 pound spool. The Rumvita listing also gives 4.5 kg in its bullets, and the ALL-CARB spec table gives 10 pounds.

Can either wire weld outdoors?

The Rumvita listing claims its wire is great for welding outdoors or in drafty conditions, while also saying to use it with a CO2 or CO2/Argon mix gas supply. Those two statements sit in tension, since shielding gas is hard to protect outdoors or in drafty conditions, so weigh the gas requirement against the outdoor claim. The ALL-CARB listing states self-shielded wire with no gas required, and names light structural and general fabrication uses.

Do either of these wires state a warranty?

Neither listing states a warranty term. Neither listing states a CSA, UL or ETL listing either, so both score zero on safety listing and warranty.

Related: best MIG wire 0.8 mm, flux core vs MIG for outdoor use, and the welding consumables hub.

Scoring, line by line

Both wires are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Neither listing states a safety listing or a warranty term, so both score zero on safety and warranty, and the gap between them comes from performance, build and value alone.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Rumvita E71T-GS 9.6 28 20 20 n/a 0
ALL-CARB E71T-GS 9.5 27 20 20 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

More buying guides

Welding Consumables ·

MIG Welding Wire Types and Which to Buy

ER5356, ER4043 and ER70S-6 cover aluminum and mild steel MIG work: aluminum wire for aluminum alloys, mild steel wire for steel, matched by diameter…