Aluminum MIG Wire vs TIG Rod: Which One Should You Buy?
Aluminum MIG wire feeds through the gun on a spool while a TIG rod is fed by hand, and this guide compares them from what the wire listings state: alloy, diameter, melting range, finish and gas.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
YESWELDER Silicon Aluminum Welding Wire9.7/10View on Amazon - 2
1-Lb ER308L Stainless Steel 308 TIG Welding Rod 3/32"x36"9.7/10View on Amazon - 3
PGN ER70S-6 .035" Solid MIG Welding WireView on Amazon - 4
ARCCAPTAIN Magnesium Aluminum MIG Welding Wire ER5356 .035"View on Amazon - 5
ARCCAPTAIN Magnesium Aluminum Welding Wire ER5356 .035" MIGView on Amazon - 6
ARCCAPTAIN Silicon Aluminum Welding Wire ER4043 .035" MigView on Amazon - 7
TOOLIOM ER4043 .030" Aluminum MIG Welding WireView on Amazon - 8
TOOLIOM ER4043 .035" Aluminum MIG Welding WireView on Amazon
Aluminum MIG wire and TIG rod are both filler metal for aluminum, and the difference is how the filler reaches the puddle: MIG wire feeds through the gun on a spool, while a TIG rod is fed by hand beside the torch. This guide compares aluminum mig wire vs tig rod from what the wire listings state, so the choice rests on alloy, diameter, melting range, finish and gas. The listings here show MIG wire only, so the TIG side is described from the process, not from a rod listing.
Other welders and gear to compare
PGN ER70S-6 .035" Solid MIG Welding WireCheck price on Amazon
ARCCAPTAIN Magnesium Aluminum MIG Welding Wire ER5356 .035"Check price on Amazon
ARCCAPTAIN Magnesium Aluminum Welding Wire ER5356 .035" MIGCheck price on Amazon
ARCCAPTAIN Silicon Aluminum Welding Wire ER4043 .035" MigCheck price on Amazon
TOOLIOM ER4043 .030" Aluminum MIG Welding WireCheck price on Amazon
TOOLIOM ER4043 .035" Aluminum MIG Welding WireCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Aluminum mig wire vs tig rod: the difference
MIG wire comes on a spool and feeds through the gun as the weld runs, so the welder holds the gun and the feeder drives the wire. A TIG rod is a separate stick of filler metal, fed by hand into the puddle while the other hand holds the torch. That difference decides the setup: MIG wire needs a wire feeder and a spool, while a TIG rod needs a TIG torch and a steady hand for the rod. Both fill the joint with aluminum alloy, and the alloy is chosen by the base metal.
Side by side
| Factor | MIG wire | TIG rod | Notes |
|---|---|---|---|
| Form | Wire on a spool, fed through the gun | Rod fed by hand | Listings show MIG wire on spools |
| Alloys listed | ER5356: 5052, 5083, 5356, 5454, 5456; ER4043: 3003, 5052, 6061, 6063 | Not stated | No TIG rod listing in the data |
| Diameter stated | 0.030, 0.035 and 0.045 inch | Not stated | Only MIG wire diameters are listed |
| Melting range stated | ER5356: 950 to 1175 °F; ER4043: 1065 to 1170 °F | Not stated | Only MIG wire listings state a melting range |
| After anodizing | ER5356: white; ER4043: gray | Not stated | Only MIG wire listings state anodized color |
| Shielding gas stated | Argon or helium or mix | Not stated | Only the WeldingCity listing states shielding gas |
| Spool size | 1 lb spools; 4 inch spool stated | Not stated | Only MIG wire listings state spool size |
The table lists what the wire listings state for MIG wire; the TIG rod column says where no rod listing is in the data. Always follow the alloy and the gas printed on the wire label and in the machine manual.
Alloy: ER5356 and ER4043
ER5356 is a magnesium aluminum alloy with 5.0% magnesium content, for 5xxx series aluminum-magnesium alloys such as 5052, 5083, 5356, 5454 and 5456, and it resists seawater and salt spray corrosion. ER4043 is a silicon aluminum alloy with 5% silicon, for 3003, 3004, 5052, 6061 and 6063, plus casing alloys 43, 355, 356 and 214, and it is less sensitive to weld cracking with a brighter finish. Match the alloy to the base metal: the listings name the alloys each wire suits, and the base metal decides.
Diameter and spool
The listings give 0.030 inch, 0.035 inch and 0.045 inch diameters, with 1 lb spools and a 4 inch spool stated on the WeldingCity listing. The ARCCAPTAIN listing is a pack of 5 spools of 1 lb each, and the WeldingCity listing is a pack of 5 rolls of 1 lb spools. Match the diameter to the wire feeder and the gun: the listing states the diameter, and the feeder must take it.
Melting range, finish and gas
ER5356 melts from 950 °F to 1175 °F with a density of 0.097 pounds per cubic inch, and the color after anodizing is white. ER4043 melts from 1065°F to 1170°F with a density of 0.097 lbs/in³, and the color after anodizing is gray. The WeldingCity listing states shielding gas of argon or helium or mix and AWS A5.10. The silicon in ER4043 improves fluidity and wetting action, while the magnesium in ER5356 gives higher shear strength and corrosion resistance.
The wire in the listings
The 4 listings here are all MIG wire: 2 in ER5356 and 2 in ER4043, on 1 lb spools, in 0.030 inch and 0.035 inch diameters, with 0.045 inch also listed as available. No TIG rod listing is in the data, so the rod side of this guide rests on the process, not on a rod listing. Check the alloy, the diameter and the gas on the wire label before buying.
Heat and fumes. Aluminum welding makes heat and fumes like any welding. Weld with good ventilation, wear eye protection under the helmet, and clear dry grass and anything flammable from the area.
FAQ for welders
Which aluminum filler should I use, ER5356 or ER4043?
Match the alloy to the base metal. ER5356 suits 5xxx series alloys such as 5052, 5083, 5356, 5454 and 5456, and resists seawater and salt spray corrosion. ER4043 suits 3003, 3004, 5052, 6061 and 6063, plus casing alloys 43, 355, 356 and 214, and is less sensitive to weld cracking with a brighter finish.
Can I use MIG wire as a TIG rod?
The listings describe MIG wire for the MIG process, fed through the gun on a spool. A TIG rod is a separate stick of filler fed by hand, and the listings state no TIG rod. Check the process the filler is made for on the label.
What diameter aluminum MIG wire should I buy?
The listings give 0.030 inch, 0.035 inch and 0.045 inch diameters. The ARCCAPTAIN and WeldingCity listings are 0.035 inch, and the TOOLIOM and YESWELDER listings are 0.030 inch. Match the diameter to the wire feeder and the gun.
What gas do I use with aluminum MIG wire?
The WeldingCity listing states shielding gas of argon or helium or mix. The other listings state no shielding gas. Check the gas on the wire label and in the machine manual.
Why does ER4043 give a brighter finish?
The listings state the silicon in ER4043 improves fluidity and wetting action, and the alloy is less sensitive to weld cracking and produces a brighter finish. ER5356 gives a white color after anodizing, while ER4043 gives a gray color after anodizing.
Related: welding consumables, can aluminum be MIG welded, best welder for beginners, and the MIG welders hub.




