Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Manual Tubing Notcher: How It Works and What to Buy

A manual tubing notcher cuts a saddle notch in the end of a tube so it fits tight against another tube for welding, driven by a hand drill or drill press with a hole saw.

Manual Tubing Notcher: How It Works and What to Buy
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Tube Notcher 9/16-2in Pipe Notcher 40-90 Degree Hole Saw ToolTube Notcher 9/16-2in Pipe Notcher 40-90 Degree Hole Saw Tool9.5/10View on Amazon
  2. 2KF5008 2 Inch Hole Saw Pipe Tube Notcher Tubing NotcherKF5008 2 Inch Hole Saw Pipe Tube Notcher Tubing Notcher9.4/10View on Amazon
  3. 3Jeremywell Industrial Professional Pipe & Tube Notcher PunchJeremywell Industrial Professional Pipe & Tube Notcher Punch9.3/10View on Amazon

A tube joint that fits tight starts with a notch, not a weld. Tubes meet at an angle on a roll cage, a frame or a handrail, and the end of a tube has to curve around the other before the welder strikes an arc. A manual tubing notcher cuts that curve: a hole saw on a drill turns the end of the tube into a saddle that sits flush on the mating tube, ready for fit-up. This guide walks through how it works, what sizes it fits, and what to check on the listing before you buy.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Manual tubing notcher: what it does

A manual tubing notcher holds a tube in a clamp while a drill spins a hole saw into its end. The saw cuts a curved saddle, called a fishmouth, that matches the outside of the tube it joins. The joint then fits tight with a small gap for the weld, instead of a flat end butted against a round tube with gaps at the sides. The notcher itself does not weld: it shapes the tube end so the weld has a joint worth welding.

The drive is a hand drill or a drill press. The notcher holds the tube at a set angle, the hole saw turns on the drill, and the feed is by hand on the drill or the press handle. Angle, tube size and hole saw size decide whether the notch fits: set the angle on the notcher scale, clamp a tube inside the size range, and fit a hole saw that matches the tube it joins.

Side by side

Small notchers: 1/2 to 2 in Large notchers: 3/4 to 3 in Notes
Tubing it fits 1/2 to 2 in round tube 3/4 to 3 in round tube VEVOR states 1/2 to 2 in; Eastwood 21749 and Allstar state up to 2 in. Measure the outside diameter first.
Angle range 0 to 60 degrees 0 to 50 degrees Allstar adjusts up to 45 degrees
Hole saws it takes 3/4 to 3-1/4 in Standard hole saws Eastwood 21749 takes a hole saw up to 2-1/2 in; VEVOR and WONDERSUNM state hole saws not included
Drive Hand drill or drill press Hand drill Eastwood and maXpeedingrods fit a 1/2 in hand drill
Offset from centerline Not stated Up to ±1 in WONDERSUNM notchers state the offset
Rectangular tube Up to 2 x 2-1/2 in (Eastwood) Not stated Round tube is the common job

Angle ranges come from the listings: the VEVOR notchers and the Eastwood 21749 adjust to 60 degrees, the WONDERSUNM notchers, the Eastwood 20447 and the maXpeedingrods notcher (on Amazon) adjust to 50 degrees, and the Allstar notcher adjusts up to 45 degrees. Hole saw sizes are a separate check: match the saw to the tube the notch joins, not to the tube in the clamp.

When the smaller notcher fits

  • Repair shops and home projects. The VEVOR notchers list repair shops and home projects, and fit 1/2 to 2 in round tube.
  • Small tube and pipe. A 1/2 to 2 in range covers small frames and pipe work, and the VEVOR listings state the range fits 0.5 in to 2 in round pipes.
  • More than metal. The VEVOR listings state the notcher works with metal, PVC, wood and plywood, so it covers pipe and tube across materials.
  • Rectangular tube. The Eastwood 21749 notches up to a 2 x 2-1/2 in rectangular tube, as well as round tube up to 2 in.

See our best hole saw for metal guide for the saws these notchers take, and the tubing notcher vs tubing cutter comparison for when a notch beats a straight cut.

When the larger notcher fits

  • Roll cages and chassis. The maXpeedingrods listing names exhaust, roll cages, go-kart frames, off-road projects and tubular chassis work, all in the 3/4 to 3 in range.
  • Offset notches. The WONDERSUNM notchers offset the notch by ±1 in from the centerline, with a height-adjustable cutter centerline for workpieces that do not sit on center.
  • Heavier frames. The WONDERSUNM 45 carbon steel notcher and the maXpeedingrods notcher are built for fabrication work, with needle roller bearings on the WONDERSUNM listings for smooth operation.
  • Any 1/2 in drill. The Eastwood 20447 and the maXpeedingrods notchers work with any 1/2 in hand drill, so a 1/2 in shop drill drives the notcher.

How to tell what a notcher fits

Read the listing for the range, the angle and the drive, in that order, and check each against the tube in the shop.

  • Tubing range. Listings state the range as outside diameter: 1/2 to 2 in on the VEVOR notchers, up to 2 in on the Eastwood 21749 and Allstar notchers, and 3/4 to 3 in on the WONDERSUNM, Eastwood 20447 and maXpeedingrods notchers. Measure the tube before you order.
  • Angle range. The scale runs 0 to 60 degrees on the VEVOR notchers and the Eastwood 21749, and 0 to 50 degrees on the WONDERSUNM notchers, the Eastwood 20447 and the maXpeedingrods notcher. The Allstar notcher adjusts up to 45 degrees.
  • Hole saw size and thread. The VEVOR notchers take hole saws from 3/4 to 3-1/4 in, and the Eastwood 21749 takes a standard hole saw up to 2-1/2 in. The WONDERSUNM notchers take 1/2-20 and 5/8-18 threads, and the maXpeedingrods notcher takes a 5/8-18 internal thread with a 1/2-20 external thread on its adapter. Hole saws are not included on the VEVOR and WONDERSUNM listings, so check the box before you buy.
  • Drive and mounting. The WONDERSUNM notchers clamp in a vise or bolt to a worktable, and the Allstar notcher works in a drill press or with a hand drill. The VEVOR notchers work with drill presses, milling cutters and round cutters.

When a listing states no figure for the check you need, treat it as not stated and compare on the figures the listing does give.

What to check before you buy

Match the notcher to the tube first, then to the drill and the saw. A notcher that fits the tube but takes a saw thread the shop does not stock still needs an adapter, and a notcher that fits the saw but not the tube cannot cut the notch at all. Check the angle scale, the mounting, and whether the hole saw comes in the box.

Notcher safety. A hole saw cuts fast and throws chips. Clamp the tube and the notcher before the drill turns, keep hands clear of the saw, wear eye protection, and switch the drill or press off before changing the saw. Clear chips with a brush, not a hand, and keep the work area clear of flammable material.

FAQ for welders

What size tubing does a manual tubing notcher fit?

It depends on the notcher. The VEVOR notchers fit 1/2 to 2 in round tube, the Eastwood 21749 and Allstar notchers fit up to 2 in round tube, and the WONDERSUNM, Eastwood 20447 and maXpeedingrods notchers fit 3/4 to 3 in round tube. Measure the outside diameter of the tube before you order.

What angle can a tubing notcher cut?

The VEVOR notchers and the Eastwood 21749 adjust to 60 degrees, the WONDERSUNM notchers, the Eastwood 20447 and the maXpeedingrods notcher adjust to 50 degrees, and the Allstar notcher adjusts up to 45 degrees. Set the angle on the notcher scale and check the fit before welding.

Do I need a hole saw with a tubing notcher?

Yes, and it does not come in the box on the VEVOR and WONDERSUNM listings. Match the hole saw to the tube the notch joins: the VEVOR notchers take hole saws from 3/4 to 3-1/4 in, and the Eastwood 21749 takes a standard hole saw up to 2-1/2 in.

Can a tubing notcher cut rectangular tube?

The Eastwood 21749 notches up to a 2 x 2-1/2 in rectangular tube, as well as round tube up to 2 in. The other listings here state round tube only, so check the listing when the job is rectangular tube.

What drill do I need for a tubing notcher?

A 1/2 in hand drill drives the Eastwood 20447 and the maXpeedingrods notchers, and the Allstar notcher works in a drill press or with a hand drill. The VEVOR notchers work with drill presses, milling cutters and round cutters, so match the drive to the notcher before you buy.

Related: tubing notcher vs tubing cutter, best tube bender for aluminum tubing, pipe bender vs tube bender, and the metal fab tools hub. Also see our best hole saw for metal.

More buying guides