Manual Arbor Press: Types and Uses
A manual arbor press pushes parts together or apart with a lever and a ram: how to pick tonnage and stroke, and which press suits bearings, riveting and small parts.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Arbor Press, 3 Ton Ratchet Type Arbor Press9.6/10View on Amazon - 2
CXRCY Arbor Press 1 Ton Round Ram9.5/10View on Amazon - 3
VEVOR Arbor Press, 1 Ton Manual Arbor Press9.5/10View on Amazon
A manual arbor press is a bench-top lever press that pushes parts together or apart with steady force: set the work on the anvil plate, pull the lever, and the ram presses down. A manual arbor press suits pressing bearings, riveting, bending small parts and stamping, and the size to buy follows the tonnage and height the work needs.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | VEVOR Arbor Press, 3 Ton Ratchet Type Arbor Press | 9.6/10 | Buy on Amazon |
| 2 | CXRCY Arbor Press 1 Ton Round Ram | 9.5/10 | Buy on Amazon |
| 3 | VEVOR Arbor Press, 1 Ton Manual Arbor Press | 9.5/10 | Buy on Amazon |

VEVOR Arbor Press, 3 Ton Ratchet Type Arbor Press
A 3 Ton ratchet leverage arbor press with a handwheel, a 12.2 inch / 310 mm stroke and a 6.5 inch four-hole anvil plate, for pressing bearings, bushings and U-joints.
Pros
- 3 Ton maximum working pressure, the highest here
- 12.2 inch / 310 mm maximum working stroke
- Handwheel for smooth height adjustment
- 6.5 inch diameter four-hole anvil plate, changeable
Cons
- 99.21 pounds, the heaviest press here
- No warranty term is stated
- No safety listing is stated
- Needs bench space: 18.11 x 9.84 x 23.62 inches

CXRCY Arbor Press 1 Ton Round Ram
A 1 ton cast iron arbor press with a round C45 ram, a 10.4 inch lever and a 3.54 inch anvil, for installing and removing bearings and press fit work.
Pros
- 1 ton capacity, up to 2,000 pounds of downward force
- Round ram made of C45 for a smooth move
- Long lever at 10.4 inches with non-slip rubber sleeves
- Mounts to a base during use
Cons
- No warranty is stated
- No ram bore figure is stated
- No safety listing is stated
- No stroke figure is stated, only working height

VEVOR Arbor Press, 1 Ton Manual Arbor Press
A 1 ton cast iron arbor press with a 5.9 inch / 150 mm maximum working stroke, a 0.4 inch ram bore and a 3.5 inch four-hole anvil plate.
Pros
- 1 Ton maximum working pressure
- 5.9 inch / 150 mm maximum working stroke
- Flat, pointed and round drift included
- 0.4 inch ram bore takes multiple molds
Cons
- No warranty term is stated
- No item weight is stated
- No safety listing is stated
- Listing aims at leather, jewelry and handicraft work as well as metal
Manual arbor press: how it works
The press works by leverage. Pulling the lever drives the ram down onto the work on the anvil plate, and the molds on the ram shape or move the work: a flat drift, a pointed drift and a round drift come with each press here. On the VEVOR presses, the anvil plate fixes items of different shapes and sizes, and the lever position adjusts and locks. A manual arbor press gives steady, controlled force with no power and no hydraulics.
Side by side
| Factor | VEVOR 1 Ton | VEVOR 3 Ton | CXRCY 1 Ton |
|---|---|---|---|
| Capacity | 1 Ton | 3 Ton | 1 Ton, up to 2,000 pounds |
| Max working stroke or height | 5.9 inch / 150 mm | 12.2 inch / 310 mm | 5.5 in / 140 mm, stated as height |
| Anvil plate | 3.5 inch diameter, four-hole | 6.5 inch diameter, four-hole | 3.54 in / 90 mm, 4 slot positions |
| Ram bore | 0.4 inch | 0.5 inch | Not stated |
| Weight | Not stated | 99.21 pounds | 25.0 pounds |
| Lever | Lengthening lever | Handwheel and extended lever | Long lever, 10.4 in |
These numbers are the manufacturer’s ratings exactly as each listing gives them. The VEVOR 1 Ton listing gives no item weight, and no listing states a warranty term.
Capacity: 1 ton or 3 tons
Capacity is the main choice. The VEVOR 3 Ton press delivers a maximum working pressure of 3 Ton, and its listing names pressing small metal parts and bearings, seals, stamping bushings and automotive U-joint replacement. The VEVOR 1 Ton press delivers 1 Ton, and the CXRCY press states a pressure force capacity of 1 ton, up to 2,000 pounds of downward force. A bigger stated capacity suits heavier pressing, but capacity alone does not say how tall a part the press can take.
Stroke and working height
The VEVOR 1 Ton press lists a maximum working stroke of 5.9 inch / 150 mm, and the VEVOR 3 Ton press lists 12.2 inch / 310 mm, with a handwheel for smooth height adjustment. The CXRCY press states a maximum working height of 5.5 in / 140 mm instead of a stroke, so the listings do not give a figure that compares each press on the same measure.
Anvil, molds and ram
The anvil plate is where the work sits. The VEVOR 1 Ton press has a 3.5 inch four-hole steel anvil plate, the VEVOR 3 Ton press has a 6.5 inch four-hole steel anvil plate that can be changed, and the CXRCY press has a 3.54 in / 90 mm anvil with 4 slot positions. Each press comes with flat, pointed and round drifts, and on the VEVOR presses the ram bore takes the molds: 0.4 inch on the VEVOR 1 Ton press and 0.5 inch on the VEVOR 3 Ton press. The CXRCY press states a round ram made of C45 and no ram bore figure. The bench vise for metal work guide covers the other way to hold small parts on a bench.
Arbor presses for the bench
The presses below are the gear for the jobs above: a press for bearings and small parts, with the tonnage and height the work needs.
How the presses were scored
Each press is scored on performance, build, value, safety and warranty, using only what the listing publishes.
FAQ for welders
What is a manual arbor press used for?
Pressing bearings, riveting, bending, stamping, punching, forming and installing and removing bearings, among the uses the listings state. The VEVOR 3 Ton listing names pressing small metal parts and bearings, seals, stamping bushings and automotive U-joint replacement, and the CXRCY listing names product assembly, maintenance, riveting and installing and removing bearings.
How much force does a 1 ton arbor press give?
The CXRCY listing states a pressure force capacity of 1 ton, up to 2,000 pounds of downward force. The VEVOR 1 Ton listing states a maximum working pressure of 1 Ton without a pound figure.
What is the difference between the 1 ton and 3 ton presses here?
Capacity and stroke. The 3 Ton press delivers 3 Ton with a maximum working stroke of 12.2 inch / 310 mm, while the 1 Ton presses deliver 1 Ton: the VEVOR 1 Ton lists a maximum working stroke of 5.9 inch / 150 mm and the CXRCY lists a maximum working height of 5.5 in / 140 mm. The 3 Ton press also weighs 99.21 pounds, against 25.0 pounds for the CXRCY press.
Do arbor presses come with molds?
The presses here do: each comes with flat, pointed and round drifts. On the VEVOR presses, the ram bore takes the molds, at 0.4 inch on the 1 Ton press and 0.5 inch on the 3 Ton press.
Can an arbor press install bearings?
Yes, as the listings state it. The VEVOR 3 Ton listing names pressing small metal parts and bearings and automotive U-joint replacement, and the CXRCY listing names installing and removing bearings and other press fit work.
Related: the steel vs aluminum blind rivets comparison, the bench vise for metal work picks, the bench vise vs post vise comparison and the metal fab tools hub.




