Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Gouging Rod Sizes: Carbon Rods for Arc Gouging

Carbon arc gouging rods run from 1/8 inch to 1/2 inch in diameter, and the right size follows the groove, the metal and the torch.

Gouging Rod Sizes: Carbon Rods for Arc Gouging
On this page

A crack runs down a weld on a loader bucket, and the fix starts with cutting the crack out clean so the new weld has sound metal to bite. That is the job for carbon arc gouging, and gouging rod sizes decide how wide and how deep the cut runs. This guide explains the sizes on the shelf, what each size suits, and how to match a rod to the groove, the metal and the torch.

As an Amazon Associate I earn from qualifying purchases. WeldGearLab earns a commission when you buy through links on this site, at no extra cost to you.

Gouging rod sizes and what they mean

Diameter is the size that matters on a gouging rod. The rods in the listings here run from 1/8 inch to 1/2 inch in diameter. SÜA lists its rods at 12 inches long, and PATIKIL gives 305 mm, which the maker gives as 12 inches. A thicker rod cuts a wider groove and clears more metal with each pass, while a thinner rod cuts a narrow groove and suits shallow work and thin metal. SÜA lists diameters of 1/8, 5/32, 3/16, 1/4, 5/16, 3/8 and 1/2 inch. PATIKIL lists rods of 5 mm, 6 mm, 8 mm and 10 mm, each 305 mm long, with diameters of 3/16, 1/4, 5/16 and 3/8 inch.

Rod diameter Length Pack sizes in the listings What it suits
1/8 in 12 in 100 rods Light cuts and thin metal
5/32 in 12 in Not stated Light cuts and shallow grooves
3/16 in 12 in 10 rods, 100 rods Light to medium cuts
1/4 in 12 in 10 rods Medium cuts and crack repair
5/16 in 12 in 10 rods, 50 rods Medium to heavy cuts
3/8 in 12 in 10 rods, 20 rods, 50 rods Heavy cuts and hardfacing removal
1/2 in 12 in Not stated Heaviest cuts and widest grooves

Pack size varies by brand and diameter. SÜA sells the 1/8 inch rod in packs of 100, and the 5/16 and 3/8 inch rods in packs of 50. PATIKIL sells packs of 10 rods, with a 20 rod pack for the 3/8 inch size. Blue Demon sells the 1/8 and 3/16 inch rods in 100 piece packs. Buy the pack that matches the amount of gouging on the job, and keep spare rods dry on the shelf.

How to pick a rod diameter

Start with the groove, not the rod. A narrow crack or a shallow U-groove takes a thin rod, while a wide groove or a thick hardfacing deposit takes a thick rod. A rod that is too thick for the groove cuts past the edges and wastes metal, while a rod that is too thin takes pass after pass to clear the same groove. The metal matters as well: SÜA lists carbon steel, stainless steel, copper, aluminum, cast iron, nickel alloys and manganese steel for its rods. Check that the rod fits the torch jaws before striking an arc, and check that the air jet can clear molten metal from the groove. When the choice is close, pick the thinner rod and make an extra pass.

What gouging rods are made of

A gouging rod is a carbon and graphite core with a thin copper coating. SÜA describes a balance of carbon and graphite under a thin, high purity copper coating, and says the coating keeps conductivity high and the arc steady. Blue Demon gives the mix as 80% graphite and 20% copper. PATIKIL says its rods are baked at 2200 C and then plated with copper, and lists copper and graphite as the material. The copper layer carries current to the arc, and PATIKIL says its rods are not easy to break.

How carbon arc gouging works

Carbon arc gouging melts metal with an electric arc and blows it away with a jet of compressed air. SÜA says the air comes from an ordinary shop air compressor. On DC power, PATIKIL says the carbon rod connects to the positive pole of the power supply and the workpiece connects to the negative pole. PATIKIL gives an angle of 45 degrees to the workpiece in its instructions for its rods. Keep the arc short, and let the air jet clear the groove as the rod moves along. Keep rods dry, and dry them before use when they get wet. The carbon arc gouging setup guide covers the torch, the air supply and the holder in more detail.

Common jobs for gouging rods

  • Removing hardfacing. Old hardfacing deposits come off with a wide groove before the part gets a fresh layer.
  • Repairing cracks. Gouge out a crack to sound metal, then weld the groove shut.
  • Cutting U-grooves. A U-groove cut with a rod shapes the joint for weld preparation.
  • Dipper teeth. Worn tips come off the teeth of digging equipment before new tips go on.
  • Cutting cast iron and manganese steel. SÜA lists cast iron and manganese steel, and the rods suit railroads, steel mills and paper mills.
  • Shipyards and pipelines. PATIKIL lists shipbuilding, highway and bridge work, the steel industry and oil pipelines, and notes double-sided welding for full penetration welds.

Safety and setup

Gouging throws molten metal and makes arc flash, fumes and noise, so wear a welding helmet, heavy gloves and flame resistant clothing, and keep the skin covered. Gouge with ventilation or outdoors with the head out of the plume, and clear dry grass and anything flammable from the area. Check the torch, the air hose and the cable before striking an arc, and keep the work clamped so it cannot move while the rod runs along the groove. Fumes from coated or galvanized steel call for extra care, so check the manual and the safety data for the metal before gouging it.

FAQ for welders

Which gouging rod size suits a shallow groove?

Start with the groove. A shallow groove or a thin section takes a rod at the small end of the range, such as 1/8 or 3/16 inch, while a wide groove takes a thicker rod. The rods in the listings here run from 1/8 inch to 1/2 inch, so the range covers light repair work and heavy removal.

Are gouging rods copper coated?

The rods in the listings here are copper coated. SÜA coats its rods with a thin, high purity copper layer, PATIKIL plates its rods with copper after baking, and Blue Demon sells copper coated carbons. The makers say the coating improves conductivity, and SÜA says it keeps the arc steady.

Can a carbon rod gouge stainless steel?

Yes. SÜA lists stainless steel among the metals its rods work on, along with carbon steel, copper, aluminum, cast iron, nickel alloys and manganese steel. Match the rod diameter to the groove, and check the manual for the settings on the metal.

What polarity do gouging rods use?

On DC power, the carbon rod connects to the positive pole of the power supply and the workpiece connects to the negative pole. That is the setup PATIKIL gives in its instructions for its rods on DC power. Check the torch manual before striking an arc on a new setup.

How should gouging rods be stored?

Keep rods dry on the shelf, away from damp air and wet floors. PATIKIL says a rod that gets wet has to dry before use.

Related: plasma gouging vs carbon arc gouging, best consumables for plasma cutter, best plasma cutter consumables for beginners, and the welding consumables hub.

More buying guides

TIG Welders ·

What Size TIG Filler Rod for 1/8 Steel?

Choose the right TIG filler rod size for 1/8 steel by comparing 3/32 and 1/16 inch ER70S-6 wire for puddle control, joint fit-up, and…