Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Cost of a Plasma Cutter: What Affects the Price

The cost of a plasma cutter depends on how thick it cuts, what power it needs, how the arc starts and what else comes in the box.

Cost of a Plasma Cutter: What Affects the Price
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARCCAPTAIN iControl CUT60 Pro Plasma Cutter MachineARCCAPTAIN iControl CUT60 Pro Plasma Cutter Machine9.8/10View on Amazon
  2. 2YESWELDER CUT-65DS PLUS Plasma CutterYESWELDER CUT-65DS PLUS Plasma Cutter9.7/10View on Amazon
  3. 3YESWELDER 45PCS Plasma Cutting Torch Consumables Set TipYESWELDER 45PCS Plasma Cutting Torch Consumables Set Tip9.7/10View on Amazon

A rusted bracket needs trimming, a patch panel needs a clean edge, and the angle grinder is slow going. The cost of a plasma cutter depends on how thick it cuts, what power it needs, how the arc starts, whether it can run on a CNC table, and what else you need to buy with it. This guide walks through each factor so you can see where the money goes and what you can skip.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Cost of a plasma cutter in one paragraph

Cut capacity drives the cost of a plasma cutter more than any other factor. A 55A machine like the ARCCAPTAIN CUT55 MP cuts steel up to 1 inch thick, while the 65A ARCCAPTAIN CUT65 reaches a max cut of 1-3/16 inch on 220V. Input power, pilot arc, CNC readiness, app control, extra modes and warranty move the price after that, and consumables and the air supply are costs that follow the machine home.

Side by side

Costs less Costs more Why it moves the price
Cut capacity 55A, cuts up to 1 inch 65A, cuts up to 1-3/16 inch Bigger power supply and torch
Clean cut on 220V 5/8 inch 3/4 inch Thicker clean cuts need more amps
Input power 110V, up to 5/8 inch max cut 220V, up to 1-3/16 inch max cut Full power needs a 220V circuit
Pilot arc High-frequency arc start Non-HF blowback pilot arc Low-interference start for CNC work
CNC cutting Hand cutting ARC OK and THC signal outputs Ports and signal outputs are built in
Control Front panel controls App control from a phone Adjust current and watch pressure from a phone
Extra modes Plate cutting Expanded metal, rust removal and gouging More modes need more circuitry
Warranty 2 years 3 years Longer cover costs the maker more

Compare the clean cut figure, not the max cut figure, since the max cut is a rough sever cut. Check the figures at the voltage you have: the ARCCAPTAIN CUT65 cuts 1-3/16 inch on 220V and only 5/8 inch on 110V.

Cut capacity sets the price

Cut capacity is the number that moves the price most. A 55A cutter and a 65A cutter sit in different classes because the higher amp machine cuts thicker steel. The ARCCAPTAIN CUT55 MP (on Amazon) delivers up to 55A and cuts steel up to 1 inch thick, with a cutting range of 12 to 15mm on 120V and 18 to 26mm on 240V. The AWT CUT-55 also runs at 55A, with a clean cut of 3/8 inch on 110V and 5/8 inch on 220V, and a max cut of 1/2 inch on 110V and 3/4 inch on 220V. The 65A ARCCAPTAIN CUT65 MP (on Amazon) cuts up to 32mm on steel, stainless steel and copper. Pay for the clean cut figure at the voltage you have, not the max cut figure at a voltage you do not have. See the best plasma cutter guide for machines compared on these same figures.

Input power and what it costs you

A plasma cutter needs the right power before it needs anything else. The ARCCAPTAIN CUT65 and the AWT CUT-55 both run on 110V and 220V, so either machine works in a home garage and a shop with a 220V circuit. The ARCCAPTAIN CUT55 MP runs on 120V and 240V, and the CUT65 MP runs on 240V. A machine that needs 240V cuts at full power only where that circuit exists. The CUT65 also carries a note from the maker: for metals over 18mm, use a stable 220V input, since unstable voltage may reduce cutting performance. See the best dual voltage plasma cutter guide for machines that switch between voltages.

Pilot arc, CNC and app control

How the arc starts is the next price factor. The AWT CUT-55 uses a high-frequency non-touch pilot arc, which starts the arc without touching the metal. The ARCCAPTAIN CUT55 MP and CUT65 MP use a non-HF blowback pilot arc, which starts without touching the metal and without the electromagnetic interference of a high-frequency start. That matters on a CNC table, where interference can disturb the controls, and the CUT65 MP is built for that work with pre-installed ARC OK and THC signal outputs and dedicated 2-pin arc voltage and 5-pin signal control ports. App control is another step up: the CUT55 MP and CUT65 MP connect to a phone app that adjusts the cutting current, monitors air pressure and shows error alerts.

Consumables, air and warranty

A plasma cutter keeps costing money after the box opens. The torch wears nozzles and electrodes as it cuts, and the maker of the CUT55 MP and CUT65 MP says to change the nozzle when using plasma gouging, so consumables are a running cost, not a one-time cost. Compressed air is the other running cost: the CUT55 MP recommends 0.3 to 0.55 MPa or 0.4 MPa (57.5 PSI), while the CUT65 MP recommends 0.3 to 0.55 MPa or 43 to 80 PSI. Warranty is the last line on the price: the ARCCAPTAIN CUT65 carries a 2-year warranty, and the CUT55 MP and CUT65 MP each carry a 3-year warranty. The AWT CUT-55 states no warranty term, so compare the warranty terms before you buy. See the best consumables for plasma cutter guide for kits that fit these torches.

What you can skip

Not every feature is worth paying for. If you cut plate steel in a home garage, you can skip CNC ports, app control and gouging modes and put the money into cut capacity and a longer warranty. If you cut expanded metal or rusty steel, the modes that keep the arc steady on mesh and the non-touch pilot arc that starts on painted and rusty metal are worth having. If you run a CNC table, the ARC OK and THC signal outputs and the non-HF blowback start are the features that make the CUT65 MP ready for that work. Match the machine to the thickest metal you cut often, not the thickest metal you cut once.

Plasma cutting arc flash and fumes. A plasma arc is bright enough to damage eyes, and cutting galvanized or painted steel makes fumes that need fresh air. Wear a welding helmet with the right shade, gloves and flame-resistant clothing, work with good ventilation or outdoors with your head out of the plume, and clear dry grass and anything flammable from the area. Keep the air supply dry and the work clamped, and check the machine manual for the settings your metal needs. See the OSHA welding overview and the Safety Disclaimer.

FAQ for welders

What matters most in the cost of a plasma cutter?

Cut capacity matters most. A 65A machine that cuts up to 1-3/16 inch costs more than a 55A machine that cuts up to 1 inch, because the higher amp machine needs a bigger power supply and torch.

Does a plasma cutter need an air compressor?

Yes. A plasma cutter needs a steady supply of compressed air to blow the molten metal out of the cut. The ARCCAPTAIN CUT55 MP recommends 0.3 to 0.55 MPa, and the CUT65 MP gives the same range as 43 to 80 PSI.

What is the difference between max cut and clean cut?

Max cut is the thickest metal the arc can sever, and clean cut is the thickest metal it cuts with a smooth edge. Compare machines on the clean cut figure at the voltage you have.

Is a dual voltage plasma cutter worth it?

It is worth it if you work in more than one shop or your garage has only 110V today. The ARCCAPTAIN CUT65 and the AWT CUT-55 both run on 110V and 220V, so they cut light metal on 110V and thicker metal on 220V.

When does a CNC-ready plasma cutter pay off?

Only when you run a CNC cutting table. The ARCCAPTAIN CUT65 MP is built for CNC work with ARC OK and THC signal outputs and 2-pin arc voltage and 5-pin signal control ports.

Related: best plasma cutter, best dual voltage plasma cutter, plasma cutter vs MIG welder, and the plasma cutters hub. Also see the best consumables for plasma cutter guide.

More buying guides