Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Plasma Cutter (2026): 5 Picks Compared

Five plasma cutters compared by amps, max cut, clean cut, voltage and warranty, for home shops and small fab shops.

Best Plasma Cutter (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Reboot 60ABest OverallReboot 60A9.5/10View on Amazon
  2. 2ARCCAPTAIN 55ABest for Mesh and RustARCCAPTAIN 55A9.5/10View on Amazon
  3. 3Bestarc 75ABest for Thick MetalBestarc 75A9.5/10View on Amazon
  4. 4FEIFANKE 55ABest Included KitFEIFANKE 55A9.5/10View on Amazon

A rusted bracket needs a new edge, a sheet of plate needs a window cut for a patch, and the angle grinder is too slow for the job. A plasma cutter turns that work into a steady pass along a line, with a clean edge and little grinding after. The best plasma cutter for a home shop or small fab shop is one that starts its arc without fuss, cuts the thickness on the bench, and runs on the power and air already in the shop.

This roundup compares five plasma cutters by amps, max cut, clean cut, voltage and warranty. All five are dual voltage, and only one states a warranty term, so the choice turns on stated cut capacity and what comes in the box.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Reboot 60A: 60A with a 1 year manufacturer warranty, auto shutdown and a 10.14 lb build. Check price on Amazon
  • Best for Mesh and Rust ARCCAPTAIN 55A: 55A with mesh cutting, rust removal and air pressure alerts. Check price on Amazon
  • Best for Thick Metal Bestarc 75A: 75A with a 30 mm max cut and 1/2 in clean cut. Check price on Amazon
  • Best Included Kit FEIFANKE 55A: 55A with a 5 m torch, ground clamp, adapter and nozzles in the box. Check price on Amazon

The machines

Reboot 60A Plasma Cutter 120V/240V Dual Voltage

Reboot 60A Plasma Cutter 120V/240V Dual Voltage

Reboot9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60A dual voltage cutter that slices 1/2 in steel on 120V and 5/8 in on 240V, with contact cutting, 2T/4T and a 1 year manufacturer warranty.

Pros

  • 1 year manufacturer warranty, the only stated term here
  • 5/8 in max cut on 240V, 1/2 in clean cut
  • Auto-detects input voltage, 10-35A at 120V or 30-60A at 240V
  • 10.14 lb with an ergonomic grip

Cons

  • No dimensions are stated
  • Contact cutting only, with no pilot arc stated
  • Needs a 50A+ breaker on 120V, per the listing
  • No LED screen or air pressure display is stated
ARCCAPTAIN 55A Non-HF Plasma Cutter Machine

ARCCAPTAIN 55A Non-HF Plasma Cutter Machine

ARCCAPTAIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A non-HF cutter with blowback pilot arc, 110V/220V, a 1 in max cut, mesh cutting and rust removal, with air pressure alerts on a large LED screen.

Pros

  • 26 mm max cut at 55A on 220V, with 3/5 in clean cuts
  • Mesh cutting and rust removal modes
  • Air pressure alerts at below 30 PSI and above 80 PSI
  • Blowback pilot arc starts without touching the metal

Cons

  • No warranty term is stated
  • External air compressor required, not included
  • No dimensions or weight are stated
  • Post-flow cooling adjusts from 5 to 15s, with no recommended setting stated
Bestarc Plasma Cutter Machine

Bestarc Plasma Cutter Machine

bestarc9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 75A cutter with HF pilot arc, 110V/220V, a 1/2 in clean cut and 1.2 in max cut, with an air sensor, LED screen and 2T/4T modes.

Pros

  • 75A, the highest here, with a 30 mm max cut
  • 1/2 in clean cut on iron, steel, aluminum and copper
  • Air sensor displays pressure on the front panel
  • Pilot arc timing adjusts up to 15s for mesh cutting

Cons

  • No warranty term is stated
  • Compressor needs to be purchased separately
  • Breaker guidance is unclear in the listing
  • The 30 mm cut is listed at 70 PSI, above the recommended 65 PSI
FEIFANKE 55A Plasma Cutter Machine,110V/220V Dual

FEIFANKE 55A Plasma Cutter Machine,110V/220V Dual

FEIFANKE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A cutter with non-touch pilot arc, auto 110V/220V, a 3/4 in max cut and 1/2 in clean cut on 220V, with a 5 m torch and a full kit in the box.

Pros

  • 3/4 in max cut and 1/2 in clean cut on 220V
  • Auto 110V/220V adaptation, with no converter needed
  • 5 m torch, ground clamp, adapter, ceramic nozzle and 2 nozzles included
  • Over-current, over-voltage, overload and overheat protection stated

Cons

  • No warranty term is stated
  • No air compressor is named as included
  • No dimensions are stated
60A Plasma Cutter,110V/220V Dual Voltage High

60A Plasma Cutter,110V/220V Dual Voltage High

haxiaoer9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60A cutter with contact arc starting, 110V/220V, a 19 mm maximum cutting capacity and a 50-60 PSI working pressure, for steel, stainless steel, aluminum and copper.

Pros

  • 19 mm maximum cutting capacity
  • Cuts carbon steel, stainless steel, aluminum and copper
  • Contact arc starts on slightly rusty or painted metal, per the listing
  • Narrow kerf with minimal heat-affected zone, per the listing

Cons

  • No warranty term is stated
  • No dimensions, weight or 2T/4T modes are stated
  • No protections, air filter or post-flow cooling are stated

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Max amps Max cut Clean cut Voltage Warranty
Reboot 60A 9.5/10 60A 5/8 in (16 mm) 1/2 in (12 mm) 120V/240V 1 year
ARCCAPTAIN 55A 9.5/10 55A 1 in (26 mm) 3/5 in 110V/220V Not stated
Bestarc 75A 9.5/10 75A 1.2 in (30 mm) 1/2 in 110V/220V Not stated
FEIFANKE 55A 9.5/10 55A 3/4 in (20 mm) 1/2 in (12 mm) 110V/220V Not stated
Haxiaoer 60A 9.4/10 60A 19 mm Not stated 110V/220V Not stated

Ratings in this table are the makers’ own claims taken from each product page (4 November 2026). Where a listing contradicts itself, both figures are shown.

What the listings tell you

Five plasma cutter listings were read for this roundup. Three state a max cut of 20 mm or more, and three state a clean cut of 1/2 in. Three state a pilot arc or non-touch start, and two state contact cutting. None states a CSA, UL or ETL listing, and only one states a warranty term.

Buying guide: the best plasma cutter for home and shop

Amps and cut capacity

Amps and cut capacity go together: the Bestarc runs 75A with a 30 mm max cut, while the ARCCAPTAIN runs 55A with a 26 mm max cut and the FEIFANKE runs 55A with a 20 mm max cut. The Reboot runs 60A with a 16 mm max cut, and the Haxiaoer runs 60A with a 19 mm max cut. Check the max cut and the clean cut together, since a max cut is not a clean cut.

Pilot arc or contact start

Pilot arc starts the arc without touching the metal. The ARCCAPTAIN uses a blowback pilot arc, the Bestarc uses an HF pilot arc, and the FEIFANKE uses a non-touch pilot arc. The Haxiaoer and Reboot use contact cutting, where the tip touches the surface. Pilot arc suits rusty, painted or dirty metal, per the listings.

Air pressure and compressor

Every cutter here needs compressed air, and none includes a compressor. The ARCCAPTAIN states a recommended pressure of 55 PSI on 110V and 50 to 75 PSI on 220V, with alerts below 30 PSI and above 80 PSI. The Bestarc states a recommended pressure within 65 PSI with a flow of 250 liters per minute. The FEIFANKE states 45 to 65 PSI, the Reboot states 30 to 70 PSI, and the Haxiaoer states 50 to 60 PSI in the bullets. Check the compressor against the pressure and flow the listing states.

Voltage and breakers

All five are dual voltage. The ARCCAPTAIN, Bestarc, FEIFANKE and Haxiaoer run 110V or 220V, while the Reboot runs 120V or 240V with auto detection. The Reboot listing recommends a 50A+ breaker on 120V and a 30A+ breaker on 240V. The Bestarc breaker guidance is unclear in the listing, so check the manual before ordering.

What comes in the box

The FEIFANKE box holds a 5 m torch, ground clamp, adapter, ceramic nozzle and 2 nozzles. The ARCCAPTAIN includes a metal-cased air filter with a 1/4 in NPT fitting. The Bestarc includes an air filter with a 1/4 NPT connector. The Haxiaoer and Reboot listings name no included extras beyond the cutter. Check what comes in the box before ordering.

Before You Strike an Arc

  • Power: the ARCCAPTAIN, Bestarc, FEIFANKE and Haxiaoer run 110V or 220V, while the Reboot runs 120V or 240V with auto detection, so check the outlet before ordering.
  • Air: every cutter here needs compressed air, and none includes a compressor, so check the compressor against the pressure the listing states.
  • Consumables: the FEIFANKE box includes a ceramic nozzle and 2 nozzles, and the ARCCAPTAIN listing states the arc system extends the life of consumables.
  • Arrival: the FEIFANKE listing states a 5 m torch and a ground clamp in the box, so check the torch and clamp on arrival.
  • Warranty: only the Reboot states a warranty term, 1 year manufacturer, so check the listing for a stated term before ordering.

FAQ for welders

What does a plasma cutter do?

A plasma cutter cuts metal with a plasma arc and compressed air. The cutters here cut steel, aluminum and copper, with max cuts from 16 mm to 30 mm. The ARCCAPTAIN also cuts mesh and cleans rust, per the listing.

What is a pilot arc plasma cutter?

A pilot arc cutter starts its arc without touching the metal. The ARCCAPTAIN uses a blowback pilot arc, the Bestarc uses an HF pilot arc, and the FEIFANKE uses a non-touch pilot arc. Pilot arc suits rusty, painted or dirty metal, per the listings.

Does a plasma cutter need gas or air?

The cutters here need compressed air, not gas. The ARCCAPTAIN and Bestarc listings state an external air compressor is required, and all five state an air pressure range. None includes a compressor.

How does a plasma cutter work?

The listings describe an arc started by pilot arc or contact, with compressed air and an IGBT inverter. The ARCCAPTAIN, Bestarc and FEIFANKE listings describe a pilot arc that starts without touching the metal, while the Haxiaoer and Reboot listings describe contact cutting. The arc cuts steel, aluminum and copper, per the listings.

Related: the best inverter plasma cutter, the pilot arc vs high frequency plasma cutter comparison, the air compressor for plasma cutter and the plasma cutters hub.

Scoring, line by line

Each cutter is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. None of the five states a CSA, UL or ETL listing, so all score zero on safety, and only the Reboot states a warranty term, 1 year manufacturer, so it is the only pick with warranty points. Performance turns on stated amps and cut capacity, build on the torch and included kit, and value on what the stated specs deliver for the class.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Reboot 60A 9.5 29 20 20 0 2
ARCCAPTAIN 55A 9.5 32 22 21 0 0
Bestarc 75A 9.5 32 21 21 0 0
FEIFANKE 55A 9.5 29 21 21 0 0
Haxiaoer 60A 9.4 27 19 19 0 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides