Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

CNC Plasma Cutter Parts: Which Consumables to Replace

CNC plasma cutter parts wear out at the nozzle and electrode first; this guide covers which consumables to replace, how to match them to your torch, and four kits to keep on hand.

CNC Plasma Cutter Parts: Which Consumables to Replace
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 160pcs PT-31 Nickel Plated Extended Air Plasma60pcs PT-31 Nickel Plated Extended Air Plasma9.6/10View on Amazon
  2. 2Bestarc Blow Back Plasma Cutter Torch ConsumablesBestarc Blow Back Plasma Cutter Torch Consumables9.6/10View on Amazon
  3. 3TIANLYLIN 23 Pcs IPT-60 Plasma Cutter TorchTIANLYLIN 23 Pcs IPT-60 Plasma Cutter Torch9.6/10View on Amazon
  4. 4SG-55 AG-60 WSD-60 .030" Plasma Cutter CuttingSG-55 AG-60 WSD-60 .030" Plasma Cutter Cutting9.5/10View on Amazon

CNC plasma cutter parts are the wear parts inside the torch: the nozzle, the electrode, the shield cup, the swirl ring and the gas ring. The nozzle and the electrode wear first, and when they wear the cut edge turns ragged and the arc gets hard to start. This guide covers which cnc plasma cutter parts to replace, how to match them to your torch, and four kits to keep on hand.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

60pcs PT-31 Nickel Plated Extended Air Plasma

60pcs PT-31 Nickel Plated Extended Air Plasma

KERUE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60 piece nickel-plated consumable kit for PT-31 torches, with extended nozzles, electrodes, ceramic cups and gas rings for CUT-40, CUT-50D and CT-312 machines.

Pros

  • 60 pieces in one kit, the largest count here
  • Nickel-plated extended nozzles and electrodes
  • Includes 10 ceramic shroud cups and 20 gas rings, not just nozzles and electrodes
  • Fits PT-31, JG-40 and WSD-40 torches

Cons

  • Fits only the PT-31 torch family, so check your torch before ordering
  • No storage box is named in the listing
  • 60 pieces is a large stock for a welder who cuts rarely
  • Only 10 electrodes among 60 pieces, so they run out before the nozzles do
Bestarc Blow Back Plasma Cutter Torch Consumables

Bestarc Blow Back Plasma Cutter Torch Consumables

bestarc9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 23 piece IPT-60 torch consumable kit with 10 nozzles at 0.8 mm, 10 electrodes, a shield cup, a swirl ring and a wire guide, in a storage box.

Pros

  • Complete wear set: nozzles, electrodes, shield cup, swirl ring and wire guide
  • 10 nozzles at 0.8 mm and 10 electrodes, matched counts
  • Storage box included for longer service life
  • Fits IPT45, IPT53 and IPT60 torch heads and many Bestarc machines

Cons

  • Fits only the IPT torch family, so check your torch before ordering
  • Nozzle size is fixed at 0.8 mm, with no other size in the kit
  • 23 pieces is a smaller stock than the 60 piece PT-31 kit
  • No warranty term is stated in the listing
TIANLYLIN 23 Pcs IPT-60 Plasma Cutter Torch

TIANLYLIN 23 Pcs IPT-60 Plasma Cutter Torch

TIANLYLIN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 23 piece IPT-60 consumable kit with 10 electrodes, 10 tips at 1.0 mm, a shield cap, a stand-off and a swirl ring for PT-60 and PT-40 series torches.

Pros

  • 10 tips at 1.0 mm with 10 electrodes, matched counts
  • Includes a shield cap, stand-off and swirl ring
  • Fits PT-60, IPT-60, PT-40 and IPT-40 series torches
  • Listed as easy to install and replace

Cons

  • Listed as replacement parts, not original parts
  • Fits only the PT-60 and PT-40 torch series
  • Nozzle size is fixed at 1.0 mm, with no other size in the kit
  • No warranty term is stated in the listing
SG-55 AG-60 WSD-60 .030" Plasma Cutter Cutting

SG-55 AG-60 WSD-60 .030" Plasma Cutter Cutting

KERUE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 50 piece tip nozzle kit for SG-55, AG-60 and WSD-60 torches, with a slag-resistant coating for clean cuts on CUT60 and CUT50 machines.

Pros

  • 50 nozzles in one kit, the largest nozzle count here
  • Slag-resistant coating keeps the cutting process cleaner
  • Fits SG-55, AG-60 and WSD-60 torches on CUT60, CUT50 and CUT-55DS machines
  • Listed for clean, smooth cuts with minimal slag

Cons

  • Nozzles only: no electrodes, cups or rings in the kit
  • Fits only the SG-55, AG-60 and WSD-60 torch family
  • No storage box is named in the listing
  • A 50 piece stock of one part suits heavy cutting more than occasional use

What wears out first

The nozzle shapes the plasma arc, and its opening grows with use until the cut widens and the edge turns rough. The electrode carries the current, and its tip pits with use until the arc wanders or fails to start. The shield cup guards the nozzle, the swirl ring spins the gas around the arc, and the gas ring meters the flow; each of these wears more slowly than the nozzle and electrode. A CNC table makes the wear easy to miss, since the torch keeps running the same program while the cut quality drifts, so check the consumables when the edge changes.

CNC plasma cutter parts side by side

Kit Gear Score Pieces Nozzles Electrodes Fits
KERUE PT-31 9.6/10 60 20 extended tips 10 PT-31, JG-40, WSD-40
Bestarc IPT60 9.6/10 23 10 at 0.8 mm 10 IPT45, IPT53, IPT60
TIANLYLIN IPT-60 9.6/10 23 10 at 1.0 mm 10 PT-60, IPT-60, PT-40, IPT-40
KERUE AG-60 9.5/10 50 50 None SG-55, AG-60, WSD-60

Counts and sizes are as published on each listing.

The parts kits

Each kit below covers one torch family, so match the kit to the torch on your table before you order.

How to match parts to your torch

Match the torch series first: the TIANLYLIN IPT-60 kit (on Amazon) fits IPT-60, PT-60, PT-40 and IPT-40 torches, while the Bestarc kit (on Amazon) fits IPT45, IPT53 and IPT60 torch heads. PT-31 parts fit PT-31, JG-40 and WSD-40 torches, and SG-55 and AG-60 parts fit SG-55, AG-60 and WSD-60 torches. Then match the tip size: the Bestarc kit uses 0.8 mm nozzles, the TIANLYLIN kit uses 1.0 mm tips at .039 inch, and the AG-60 kit lists two tip sizes, .030 and .035 inch. Count the pieces against how often you cut: a 60 piece kit restocks the full wear set, while a 50 piece nozzle kit restocks one part only.

When to swap a consumable

Swap the nozzle when the cut edge turns ragged, the kerf widens, or the arc gets hard to start. Swap the electrode when its tip pits or the arc wanders. Swap the shield cup when it cracks or the opening wears out of round, and swap the swirl ring and gas ring when the cut loses its clean edge for no other reason. Keep a spare set at the table, so a worn part costs minutes instead of a lost cutting session.

Use as directed. Plasma cutting gives off arc flash, fumes, hot metal and sparks, so wear a welding helmet, gloves and flame-resistant clothing, and cut in a ventilated space. Keep the air supply dry and the ground clamp on clean metal, and let cut parts cool before handling them. Never cut a closed container, and never cut galvanized metal without ventilation and a respirator.

FAQ for welders

How often should I replace plasma cutter consumables?

Replace them when cut quality drops, not on a fixed schedule. A worn nozzle widens the cut and roughens the edge, and a pitted electrode makes the arc hard to start. Check the nozzle and electrode each time the edge changes, and keep spares at the table.

Are plasma cutter consumables interchangeable between torches?

No, match the torch series. the TIANLYLIN IPT-60 kit fits IPT-60, PT-60, PT-40 and IPT-40 torches, while the Bestarc kit fits IPT45, IPT53 and IPT60 torch heads. PT-31 parts fit PT-31, JG-40 and WSD-40 torches, and SG-55 and AG-60 parts fit SG-55, AG-60 and WSD-60 torches. A part that looks the same can still seat wrong, so check the fit list before you order.

What is the difference between a nozzle and an electrode?

The nozzle shapes the plasma arc and sets the cut width, while the electrode carries the current that forms the arc. The nozzle opening grows with use and the electrode tip pits, so the two wear together, and the Bestarc and TIANLYLIN kits carry matched counts of 10 nozzles and 10 electrodes.

Do I need a shield cup and swirl ring too?

The shield cup guards the nozzle and the swirl ring spins the gas around the arc, and both wear more slowly than the nozzle and electrode. The Bestarc kit includes a shield cup and a swirl ring, and the TIANLYLIN kit includes a shield cap and a swirl ring, and the KERUE PT-31 kit includes shroud ceramic cups and gas rings, so a full kit covers the whole wear set at once.

Related: cnc plasma cutter parts, best plasma cutter, best consumables for plasma cutter, best arc plasma cutter consumables, CNC plasma vs plasma cutter difference and can a plasma cutter cut aluminum.

More buying guides