Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Plasma Cutter for Aluminum (2026): 4 Compared

Four plasma cutters for aluminum compared by amps, clean and max cut, pilot arc, safety features and warranty, for plate, mesh and shop repairs.

Best Plasma Cutter for Aluminum (2026): 4 Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YESWELDER CUT-55DSBest OverallYESWELDER CUT-55DS9.7/10View on Amazon
  2. 2AZZUNO CUT-55LBest Dedicated CutterAZZUNO CUT-55L9.7/10View on Amazon
  3. 3AWT CUT-55Best DisplayAWT CUT-559.6/10View on Amazon
  4. 4Reboot RB360Best MultiprocessReboot RB3609.5/10View on Amazon

An aluminum panel that needs a bracket cut out and a trailer side that needs a patch both start with a clean edge, and the best plasma cutter for aluminum slices the sheet without warping it or drowning the shop in grinding dust. This guide compares the cutters by amps, clean and max cut, pilot arc, safety features and warranty, using only what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

The machines

YESWELDER 55A Multifunctiona Plasma Cutter

YESWELDER 55A Multifunctiona Plasma Cutter

YESWELDER9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A 4-in-1 plasma cutter with ETL certification, non-HF pilot arc and a 2 year warranty.

Pros

  • 4-in-1: plate cutting, grid cutting, gouging and marking
  • ETL certified with IP21 water rating
  • Non-HF blow-back arc with non-touch pilot arc
  • 2 year warranty

Cons

  • Requires an external air compressor, sold separately
  • Air pressure must stay within 45 to 75 Psi
  • Clean cut of 1/2 inch at 220V is less than the 5/8 inch stated for the AZZUNO and AWT
  • 4-in-1 functions need the right consumables for each task
AZZUNO 55A Plasma Cutter, Non-Touch Pilot Arc

AZZUNO 55A Plasma Cutter, Non-Touch Pilot Arc

AZZUNO9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A dual voltage plasma cutter with non-touch pilot arc, air sensor and a 1 year warranty.

Pros

  • 55A non-touch pilot arc for painted, rusted or uneven surfaces
  • Clean cut 5/8 inch and max cut 3/4 inch at 220V
  • Air sensor with warning light for out-of-range pressure
  • 1 year manufacturer warranty

Cons

  • High-frequency arc start, unlike the non-HF YESWELDER
  • Use AZZUNO consumables only
  • Full 3/4 inch max cut needs 220V; 110V tops out at 1/2 inch
  • 1 year warranty is shorter than the 2 years on the YESWELDER
AWT Plasma Cutter,Non-Touch Pilot Arc Cutter

AWT Plasma Cutter,Non-Touch Pilot Arc Cutter

AWT9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A dual voltage plasma cutter with non-touch pilot arc, LED display and air sensor alerts.

Pros

  • 55A non-touch pilot arc, same cut figures as the AZZUNO
  • Clean cut 5/8 inch and max cut 3/4 inch at 220V
  • Air sensor with L, M and H pressure letters on the display
  • 2T/4T with pre-flow and post-flow

Cons

  • No warranty term is stated
  • High-frequency arc start, unlike the non-HF YESWELDER
  • Full 3/4 inch max cut needs 220V; 110V tops out at 1/2 inch
  • No gouging or marking mode is stated
Reboot MIG TIG Welder Plasma Cutter Non-HF Spool

Reboot MIG TIG Welder Plasma Cutter Non-HF Spool

Reboot9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 130A 7-in-1 multiprocess welder with plasma cutting to 1/2 inch and a spool gun for aluminum.

Pros

  • 7-in-1 multiprocess with plasma cutting and aluminum MIG
  • Spool gun included for aluminum welding
  • Plasma cuts to 1/2 inch, max 5/8 inch
  • Hot Start and Arc Force for stick welding

Cons

  • No warranty term is stated
  • 1/2 inch clean cut ties the smallest here
  • 130A multiprocess machine; plasma is one of 7 functions
  • Spool gun and aluminum MIG mode add setup steps for cutting-only jobs

Other welders and gear to compare

Spec sheet comparison

Cutter Gear Score Amps Clean cut @220V Max cut @220V Warranty
YESWELDER CUT-55DS 9.7/10 55A 1/2 in 20 mm 2 years
AZZUNO CUT-55L 9.7/10 55A 5/8 in 3/4 in 1 year
AWT CUT-55 9.6/10 55A 5/8 in 3/4 in Not stated
Reboot RB360 9.5/10 130A 1/2 in 5/8 in Not stated

All specs here repeat what the maker rates and the listing prints, copied down 18 November 2026.

Buying guide: how to choose the best plasma cutter for aluminum

Clean cut and max cut on aluminum

Cut figures change with voltage. At 220V the AZZUNO and AWT list a 5/8 inch clean cut and a 3/4 inch max cut, while the YESWELDER lists a 1/2 inch clean cut and a 20 mm max cut. At 110V the AZZUNO and AWT list a 3/8 inch clean cut and a 1/2 inch max cut. The Reboot lists a clean cut to 1/2 inch with a max cut of 5/8 inch, and its spool gun welds aluminum as well.

Pilot arc and arc start

Three cutters use a non-touch pilot arc that ignites without direct metal contact, which cuts consumable wear and helps on painted, rusted or uneven surfaces. The AZZUNO and AWT use high-frequency starts, while the YESWELDER uses a non-high-frequency blow-back system that avoids interference with nearby electronics. The Reboot uses a non-high-frequency plasma cutter too.

Dual voltage and air supply

Three dedicated cutters run on 110V and 220V, while the Reboot runs on 120V and 240V. The YESWELDER needs air pressure within 45 to 75 Psi from an external compressor, sold separately. The AZZUNO and AWT watch air pressure with a built-in sensor and a warning light, and the AZZUNO box includes an air hose.

Display, modes and safety

Displays show amps, air pressure and mode settings, and the AWT display shows error codes when the cutter malfunctions. The AZZUNO and AWT offer PRE-FLOW, POST-FLOW and 2T/4T settings, and the YESWELDER adds a digital display with a diagnostic system. The YESWELDER also states an IP21 water rating with overload and overheat protection.

Torch and consumables

The torch decides how long consumables last. The YESWELDER uses an IPT40 torch with a non-touch pilot arc, and the AZZUNO box includes a cutting torch, a ground clamp, 2 tips and 2 electrodes, plus a brush hammer. The AZZUNO listing says to use AZZUNO consumables only for a proper fit. The Reboot adds a spool gun for aluminum MIG welding, so one machine covers cutting and welding.

Use as directed. Wear eye and face protection rated for plasma cutting, keep the work clamped and the area clear of anything that can burn, and check air pressure and the ground clamp before each cut. Ventilate the space and keep gas hoses and cords clear of hot metal. See the OSHA welding overview and our Safety Disclaimer.

Before You Strike an Arc

  • Check the voltage: the dedicated cutters run on 110V/220V, the Reboot on 120V/240V.
  • Check the air: the YESWELDER needs 45 to 75 Psi from an external compressor, sold separately.
  • Check the cut figures: the AZZUNO and AWT list a 5/8 inch clean cut and a 3/4 inch max cut at 220V.
  • Check the consumables: the AZZUNO box includes 2 tips and 2 electrodes, and the listing says to use AZZUNO consumables only.
  • Check the warranty on arrival: the YESWELDER lists 2 years, the AZZUNO lists 1 year.

FAQ for welders

Can these plasma cutters cut aluminum?

The AZZUNO lists aluminum among its materials, the YESWELDER lists non-ferrous metals, and the Reboot lists aluminum welding with its spool gun. The AWT states cut figures but names no material.

What is the clean cut and max cut at 220V?

The AZZUNO and AWT list a 5/8 inch clean cut and a 3/4 inch max cut at 220V. The YESWELDER lists a 1/2 inch clean cut and a 20 mm max cut, and the Reboot lists a 1/2 inch clean cut with a 5/8 inch max cut.

Do these cutters need an external air compressor?

The YESWELDER states that an external air compressor is required and sold separately. The AZZUNO box includes an air hose. The AWT and Reboot give no compressor statement.

Which plasma cutter has a warranty?

The YESWELDER lists 2 years and the AZZUNO lists 1 year. The AWT and Reboot state no warranty term.

What is a non-touch pilot arc?

It ignites the arc without direct metal contact, which cuts consumable wear. It also gives cleaner cuts on painted, rusted or uneven surfaces, as the AZZUNO and YESWELDER listings describe.

Related: best plasma cutter, plasma cutter torch guide, and the plasma cutters hub.

Scoring, line by line

Each cutter is scored out of 10 on performance, build, value, safety and warranty, with the weights published on our How We Pick page. For a plasma cutter, safety means a stated ETL listing, overload and overheat protection, and air pressure monitoring. Only the YESWELDER states an ETL listing, and two of the four state a warranty term.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
YESWELDER CUT-55DS 9.7 32 22 21 9 3
AZZUNO CUT-55L 9.7 30 21 21 7 2
AWT CUT-55 9.6 29 21 20 7 0
Reboot RB360 9.5 28 20 20 4 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.

More buying guides