Plasma Cutter Torch Guide: Parts and Consumables
A plasma cutter torch guide matches AG-60, IPT60 and SL60 torch consumables to the torch, with tip sizes, kit contents and the four kits compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
YESWELDER AG-60 Plasma Cutter Consumables Kit9.5/10View on Amazon - 2
ARCCAPTAIN AG-60 Plasma Cutter Torch Consumables9.5/10View on Amazon - 3
ARCCAPTAIN 23Pcs IPT60 Plasma Cutter Torch9.4/10View on Amazon - 4
TIANLYLIN 10 Pcs 9-8210 & 10 Pcs 9-8215 Fit9.3/10View on Amazon
The torch sputters, the cut wanders, and the edge comes out rough. A plasma cutter torch guide matches the torch parts and consumables to the torch on the cutter, so the nozzle, electrode and cup fit the torch and the current the job needs. This guide explains the torch parts, the consumable sizes, and which kit fits which torch.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

YESWELDER AG-60 Plasma Cutter Consumables Kit
A 54 piece AG-60 kit with 0.040 in tips: 20 nozzles, 20 electrodes, 10 outer ceramic cups and 4 brackets, for AG-60, AG-60P, SG-55 and WSD-60 torches.
Pros
- 54 pieces, the largest kit here
- 20 nozzles and 20 electrodes for repeat changes
- Fits AG-60, AG-60P, SG-55 and WSD-60 torches
- Covers CUT60, CUT50DP, LGK-60, CUT-55DS and more cutters
Cons
- 0.040 in tips only, no 0.045 in size in the kit
- No stand-off, swirl ring or wire spacer guide in the set
- 54 pieces is a lot for one torch
- No stated warranty term

ARCCAPTAIN AG-60 Plasma Cutter Torch Consumables
A 24 piece AG-60 set with 0.045 in nozzles: 2 shield cups, 10 nozzles, 2 wire spacer guides and 10 electrodes, for AG-60, AG-60P, SG-55 and WSD-60 torches.
Pros
- 0.045 in nozzles for AG-60 torches
- 2 shield cups and 2 wire spacer guides included
- 10 nozzles and 10 electrodes for repeat changes
- Lists CUT55 PRO, CUT55 PROLUX and CUT 60HF cutters
Cons
- 24 pieces, less than half the 54 piece kit
- 0.045 in size only, no 0.040 in nozzles in the set
- No swirl ring or retaining cup in the set
- Fits AG-60 family torches only

ARCCAPTAIN 23Pcs IPT60 Plasma Cutter Torch
A 23 piece IPT60 set with 0.040 in nozzles: 1 stand-off, 1 retaining cup, 10 nozzles, 1 swirl ring and 10 electrodes, for IPT60 torches on CUT55 NON-HF, CUT55 MP and CUT60 Non-HF cutters.
Pros
- Copper parts for conductivity and heat resistance
- 1 stand-off, 1 retaining cup and 1 swirl ring included
- Handles fine and thick plate cutting
- Ready to use right after installation
Cons
- Fewer pieces than the 24 piece AG-60 set
- Fits IPT60 torches only
- No shield cups in the set
- Narrow cutter list: CUT55 NON-HF, CUT55 MP and CUT60 Non-HF

TIANLYLIN 10 Pcs 9-8210 & 10 Pcs 9-8215 Fit
10 9-8210 60A nozzles and 10 9-8215 electrodes, to fit Thermal Dynamics SL60 and SL100 torches; a replacement part, not the original.
Pros
- 9-8210 60A nozzle with 9-8215 electrode for SL60 and SL100 torches
- 10 nozzles and 10 electrodes for repeat changes
- Standard size, easy to install and replace
- Lightweight and compact
Cons
- No stated warranty term
- Nozzles and electrodes only, no cups or rings
- Replacement part, not the original
- Fits SL60 and SL100 torches only
Plasma cutter torch guide in one paragraph
Each kit here is a set of wear parts for one torch family. The AG-60 kits carry 0.040 in and 0.045 in tips for AG-60, AG-60P, SG-55 and WSD-60 torches, the IPT60 kit carries 0.040 in tips for the IPT60 torch, and the TIANLYLIN kit carries 9-8210 nozzles and 9-8215 electrodes for Thermal Dynamics SL60 and SL100 torches. Match the torch first, then the tip size, then the cutter on the list.
Plasma cutter torch consumables for the guide
The four kits here put the guide into practice: two AG-60 kits, one IPT60 kit and one SL60 and SL100 kit, each matched to its torch.
Side by side
| YESWELDER AG-60 | ARCCAPTAIN AG-60 | ARCCAPTAIN IPT60 | TIANLYLIN SL60/SL100 | What changes | |
|---|---|---|---|---|---|
| Torch fit | AG-60, AG-60P, SG-55, WSD-60 | AG-60, AG-60P, SG-55, WSD-60 | IPT60 | Thermal Dynamics SL60/SL100 | Match the torch first |
| Nozzle size | 0.040 in | 0.045 in | 0.040 in | 9-8210, 60A | Size follows the torch |
| Pieces | 54 | 24 | 23 | 10 nozzles, 10 electrodes | Bigger kits cover more changes |
| Cutters listed | CUT60, CUT50DP, LGK-60, CUT-55DS | CUT55 PRO, CUT55 PROLUX, CUT 60HF | CUT55 NON-HF, CUT55 MP, CUT60 Non-HF | No cutters listed | Check the cutter list |
| Best use | Full restock | AG-60 restock | Fine and thick plate | SL60 and SL100 spares | Pick by the torch |
The torch decides the kit: AG-60 kits cover the AG-60 family, the IPT60 kit covers the IPT60 torch, and the TIANLYLIN kit covers SL60 and SL100 torches.
How to match the torch
- Match the torch first. AG-60, AG-60P, SG-55 and WSD-60 torches take the AG-60 kits, the IPT60 torch takes the IPT60 kit, and SL60 and SL100 torches take the TIANLYLIN kit.
- Match the tip size to the torch. The AG-60 kits come in 0.040 in and 0.045 in, the IPT60 kit comes in 0.040 in, and the TIANLYLIN kit uses 9-8210 nozzles.
- Check the cutter list. The YESWELDER kit (on Amazon) lists CUT60, CUT50DP, LGK-60 and CUT-55DS cutters, the ARCCAPTAIN AG-60 kit lists CUT55 PRO and CUT 60HF cutters, and the IPT60 kit lists CUT55 NON-HF, CUT55 MP and CUT60 Non-HF cutters.
- Replace wear parts before they fail. The makers say timely replacement keeps the cutter performing and the cuts clean and precise, so keep spare nozzles and electrodes on hand.
Plasma cutting safety. Plasma cutting makes bright arc light, hot metal and fumes, so wear a welding helmet and gloves, keep ventilation moving, and keep flammable material clear of the cut. Check the machine manual for the torch setup and the air supply.
FAQ for welders
What consumables does a plasma cutter torch need?
Nozzles, electrodes and cups, and on some torches a swirl ring and a stand-off. The AG-60 kits hold nozzles, electrodes and cups, the IPT60 kit adds a swirl ring and a stand-off, and the TIANLYLIN kit holds nozzles and electrodes only.
What size nozzle do I need for a plasma cutter?
Match the nozzle to the torch and the current. The kits here use 0.040 in and 0.045 in tips for AG-60 torches, 0.040 in for the IPT60 torch, and 9-8210 nozzles rated 60A for SL60 and SL100 torches.
How often should I replace plasma cutter consumables?
Replace wear parts before they fail. The makers say timely replacement keeps the cutter performing and the cuts clean and precise, so keep spare nozzles and electrodes on hand.
Are AG-60 and IPT60 consumables interchangeable?
No. AG-60 consumables fit AG-60, AG-60P, SG-55 and WSD-60 torches, while IPT60 consumables fit the IPT60 torch. Match the kit to the torch on the cutter.
Do I need the original brand consumables?
The TIANLYLIN kit states it is a replacement part, not the original, for Thermal Dynamics SL60 and SL100 torches. Match the part numbers, 9-8210 for the nozzle and 9-8215 for the electrode, to the torch.
Related: best plasma cutter consumables for beginners, best consumables for plasma cutter, best plasma cutter torch under 100, and the plasma cutters hub.




