Best Air Compressor for Plasma Cutter Under $150 (2026)
Five small air compressors for plasma cutters, compared by tank size, max pressure, air delivery, noise and weight.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Biggest TankMZB 6.4 Gallon9.5/10View on Amazon - 2
Strongest DeliveryVEVOR 2.1 Gallon9.4/10View on Amazon - 3
Easiest to CarryECOMAX 3 Gallon9.4/10View on Amazon
A plasma cutter is only as good as the air behind it. Starved of clean, steady air, the arc sputters, consumables burn out early and the cut edge looks chewed. The best air compressor for plasma cutter under 150 is a small shop compressor that holds pressure and delivers enough air for light cutting work, and this guide compares five of them on tank size, max pressure, air delivery, noise and weight, using only what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Biggest Tank MZB 6.4 Gallon: 6.4 gallon tank with a stated 5.65 CFM at 115 PSI and wheels. Check price on Amazon
- Strongest Delivery VEVOR 2.1 Gallon: Stated 2.2 CFM at 90 PSI from a 1.2 HP dual-cylinder motor. Check price on Amazon
- Easiest to Carry ECOMAX 3 Gallon: Stated 16.3 pounds, a 3 gallon tank and an 11 piece kit. Check price on Amazon
The machines

MZB 6.4 Gallon Ultra Quiet Air Compressor
A 6.4 gallon oil-free compressor with a 1.2 HP motor, stated 5.65 CFM at 115 PSI and a 58 to 64 second tank fill.
Pros
- Largest tank here at 6.4 gallons with 1.2 HP output
- States 5.65 CFM at 115 PSI, the highest delivery listed
- Fills the tank in a stated 58 to 64 seconds
- Wheels, two silencers and a stated 70 dB operating noise
Cons
- No weight stated, so moving it is a guess
- No air delivery figure at 90 PSI for direct comparison
- No CSA, UL or ETL listing stated

VEVOR 2.1 Gallon Air Compressor
A 2.1 gallon oil-free compressor with a 900W dual cylinder motor, stated 2.2 CFM at 90 PSI and 116 PSI max pressure.
Pros
- States 2.2 CFM at 90 PSI from a 1.2 HP oil-free motor
- Dual tube and dual cylinder intake for faster fill
- Two silencers and a stated 70 dB noise figure
- Automatic overheating protection and pressure relief stated
Cons
- Small 2.1 gallon tank for sustained cutting
- 27 pounds with no wheels stated
- No air delivery figure at other pressures
- No CSA, UL or ETL listing stated

ECOMAX Air Compressor 3 Gallon 110 PSI Pancake
A 3 gallon pancake compressor at 16.3 pounds with a stated 0.6 SCFM at 90 PSI and an 11 piece accessory kit.
Pros
- Lowest stated weight here at 16.3 pounds with a flip-up handle
- 11 piece kit including a 25 foot air hose and blow gun
- Dual gauges and dual quick couplers for two tools
- Oil-free pump with a winding bracket for cord storage
Cons
- Only 0.6 SCFM at 90 PSI, the lowest delivery stated
- 110 PSI max with no higher pressure headroom
- 78 dB is on the louder side of this group
- No CSA, UL or ETL listing stated

Ironton Oil-Free Pancake Air Compressor, 0.3 HP
A 3 gallon oil-free pancake compressor with a 0.3 HP pump, 110 PSI max and a fold-down handle for storage.
Pros
- Wide pancake base for a stable, tip-resistant footprint
- Fold-down handle and built-in cord wrap and hose retainer
- Auto on at 85 PSI and auto off at 110 PSI for steady cycling
- Oversized regulator knob and quick coupler stated
Cons
- No air delivery figure stated at any pressure
- 0.3 HP is the smallest motor stated in this group
- No noise figure stated
- No CSA, UL or ETL listing stated

CRAFTSMAN Air Compressor
A 2 gallon portable compressor with a 1/3 HP oil-free motor, 125 PSI max and a 10 piece accessory kit.
Pros
- Highest max pressure here at 125 PSI
- 10 piece kit with hose, gauge, blow gun and couplers
- Two quick couplings and a rubber reinforced handle
- Oil-free pump with overload protection stated
Cons
- Smallest tank here at 2 gallons
- No air delivery figure stated at any pressure
- No CSA, UL or ETL listing stated
Other welders and gear to compare
LE Lematec AR-01 Air Compressor Regulator ¼ NPT. Air PressureCheck price on Amazon
VEVOR Air Compressor PumpCheck price on Amazon
Spec sheet comparison
| Model | Tank | Max pressure | Air delivery | Noise | Weight |
|---|---|---|---|---|---|
| MZB 6.4 Gallon | 6.4 gallons | 115 PSI | 5.65 CFM at 115 PSI | 70 dB | Not stated |
| VEVOR 2.1 Gallon | 2.1 gallons | 116 PSI | 2.2 CFM at 90 PSI | 70 dB | 27 pounds |
| ECOMAX 3 Gallon | 3 gallons | 110 PSI | 0.6 SCFM at 90 PSI | 78 dB | 16.3 pounds |
| Ironton 3 Gallon | 3 gallons | 110 PSI | Not stated | Not stated | 20.6 pounds |
| CRAFTSMAN 2 Gallon | 2 gallons | 125 PSI | Not stated | 78 dB | 19 pounds |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 22 October 2026. Where a listing states a figure two ways, the table shows both.
Buying guide: best air compressor for plasma cutter under 150
Tank size and recovery
The tank is the buffer between the pump and the torch. These picks run from 2 gallons to 6.4 gallons, and the bigger the tank the longer the cutter draws stored air before the pump cycles. Three listings state a delivery figure at pressure: the MZB at 5.65 CFM at 115 PSI and the VEVOR at 2.2 CFM at 90 PSI, with the ECOMAX at 0.6 SCFM at 90 PSI. The Ironton and CRAFTSMAN listings state no delivery figure at all, so they cannot be weighed against a cutter’s air demand from the listing alone. When a listing does state a fill figure, like the MZB’s 58 to 64 seconds, it tells you how quickly the unit recovers between cuts.
Pressure and delivery at the torch
Max pressures here run from 110 PSI to 125 PSI, with the CRAFTSMAN highest at 125 PSI and the Ironton and ECOMAX at 110 PSI. Max pressure is a ceiling, not a working figure: what matters at the torch is delivered air at the cutter’s required pressure, and the listing has to state it. The VEVOR states 2.2 CFM at 90 PSI and the MZB states 5.65 CFM at a working pressure of 115 PSI. Check the plasma cutter’s manual for its air requirement and match it against the compressor’s stated delivery, not its max pressure. The pancake vs vertical air compressor comparison covers tank shapes for shop use.
Noise and where you work
Stated noise runs from 70 dB on the VEVOR and the MZB bullets to 78 dB on the CRAFTSMAN and ECOMAX spec tables, and the Ironton states no noise figure. A compressor that cycles all afternoon sits in the shop with you, so the quieter stated figures matter for a home garage. Both the VEVOR and the MZB listings describe dual silencers, and the MZB adds thickened filter cotton that the maker says blocks fine dust. If the shop shares walls with the house, weight the stated noise figure alongside the tank size. The oil free vs oil lubricated air compressor guide covers pump types and upkeep.
Oil-free pumps and moisture
Every pick here lists an oil-free pump, which means no oil changes and no oil mist in the air line from the pump itself. Plasma cutting still wants dry air: moisture in the line shortens consumable life and roughens the cut. None of these listings describe a built-in dryer or water separator, so plan on the cutter’s own filtration or an add-on separator. The included accessory kits vary: the ECOMAX ships an 11 piece kit with a 25 foot hose and blow gun, and the CRAFTSMAN ships a 10 piece kit with a gauge and blow gun, while the VEVOR, Ironton and MZB list smaller or no kits.
Before You Strike an Arc
- Check the outlet first: the listings state 110 or 120 volts, corded electric, on every pick. Match the shop circuit before the first cut.
- Drain the tank and check every fitting on arrival; the listings mention quick couplers, and the kits include thread seal tape on the CRAFTSMAN and sealing tape on the ECOMAX.
- Confirm the cutter’s air demand in its manual against the compressor’s stated delivery at pressure, not just the max PSI.
- Stated noise runs 70 to 78 dB across these picks, so plan placement and hearing protection for long cutting sessions.
FAQ for welders
What size air compressor does a plasma cutter need?
The cutter’s manual states its air demand, usually as CFM at a given PSI, and the compressor listing has to meet or beat it. Among these picks, stated delivery runs from 0.6 SCFM at 90 PSI to 5.65 CFM at 115 PSI, with two listings stating no delivery figure at all. Match the manual’s figure to the listing’s stated delivery, and favor the bigger tank when the figures are close.
Can a pancake compressor run a plasma cutter?
It can for light work if the delivery matches. The Ironton and ECOMAX here are 3 gallon pancake units at 110 PSI max, and the ECOMAX states 0.6 SCFM at 90 PSI while the Ironton states no delivery figure. Short cuts with cooling pauses suit a small tank; long continuous cuts want the stored air of a bigger tank like the 6.4 gallon MZB. The pancake vs vertical air compressor comparison lays out the trade.
Oil-free or oil-lubricated for plasma cutting?
All five picks here list oil-free pumps, which the makers describe as maintenance free with no oil checks or changes. Oil-free keeps oil mist out of the air line from the pump, though the air still needs drying before it reaches the torch. See the oil free vs oil lubricated air compressor guide for the full comparison.
Does a plasma cutter need dry air?
Yes. Moisture in the air line shortens consumable life and roughens the cut edge, and none of these listings describe a built-in dryer or water separator. Plan on the filtration the cutter ships with or an add-on separator in the line. Drain the compressor tank regularly; the listings describe drain valves as part of normal upkeep.
What does CFM at 90 PSI mean on a compressor listing?
It is the volume of air the pump delivers, measured at 90 PSI of outlet pressure. A figure at pressure is the only delivery number that can be matched against a plasma cutter’s air requirement: the VEVOR states 2.2 CFM at 90 PSI and the ECOMAX states 0.6 SCFM at 90 PSI. A max PSI figure alone, like the CRAFTSMAN’s 125 PSI, says nothing about delivered volume.
Related: plasma cutter consumables for beginners and plasma cutter vs mig welder.
Scoring, line by line
Each compressor is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing, which is why every pick here shows no safety or warranty score: none of the listings state an electrical safety certification or a warranty term.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| MZB 6.4 Gallon | 9.5 | 32 | 21 | 20 | 0 | 0 |
| VEVOR 2.1 Gallon | 9.4 | 29 | 20 | 20 | 0 | 0 |
| ECOMAX 3 Gallon | 9.4 | 26 | 19 | 21 | 0 | 0 |
| Ironton 3 Gallon | 9.3 | 23 | 19 | 20 | 0 | 0 |
| CRAFTSMAN 2 Gallon | 9.3 | 24 | 16 | 20 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.






