Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Oil Free vs Oil Lubricated Air Compressor: Which One Should You Buy?

Oil free vs oil lubricated air compressors explained for plasma cutting, with four compressors ranked.

Oil Free vs Oil Lubricated Air Compressor: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Klutch 29-Gallon Air CompressorKlutch 29-Gallon Air Compressor9.5/10View on Amazon
  2. 2MZB 6.4 Gallon Ultra Quiet Air Compressor 110V/60Hz SteelMZB 6.4 Gallon Ultra Quiet Air Compressor 110V/60Hz Steel9.5/10View on Amazon
  3. 3NANPU 1/4" NPT Air Compressor Filter & Pressure RegulatorNANPU 1/4" NPT Air Compressor Filter & Pressure Regulator9.5/10View on Amazon
  4. 415-Gallon Air Compressor15-Gallon Air CompressorView on Amazon
  5. 5Oil-Free Silent Compressor Sparmax TC-620XOil-Free Silent Compressor Sparmax TC-620XView on Amazon

Oil free vs oil lubricated air compressor is the pump question behind every shop compressor. An oil free pump needs no oil and little maintenance; an oil lubricated pump runs cooler with less wear but needs oil checks. The four compressors below are the Makita MAC2400, the DEWALT DWFP55130, the Makita MAC700 and the Limodot oil free compressor: two oil lubricated Makitas and two oil free picks, ranked by what each listing states.

Other welders and gear to compare

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The difference in one paragraph

An oil lubricated pump bathes its piston in oil, which the Makita listings describe as cooler running with less wear, at the cost of oil changes and checks. An oil free pump skips the oil entirely: the DEWALT listing describes an oil free pump with extended maintenance-free operation, and the Limodot describes no oil filters to replace and cold weather starting. Compare the four listings on CFM at 90 PSI, tank size, noise and warranty.

Side by side

Oil free Oil lubricated Listings
Pump oil No oil needed stated Oil lubricated pump stated DEWALT, Limodot, Makita
Maintenance Extended maintenance-free operation stated by DEWALT; no oil filters to replace stated by Limodot No oil change interval stated in the Makita listings DEWALT, Limodot, Makita
Pump life No pump life figure stated Cooler running, less wear stated DEWALT, Limodot, Makita
Noise 68 dB (Limodot) and 71.5 dBA (DEWALT) 79 dB (MAC2400) and 80 dB (MAC700) DEWALT, Limodot, Makita MAC2400, Makita MAC700
Uses stated Trim, nailing, woodworking and inflation stated Cutting, grinding and spraying stated DEWALT, Limodot, Makita
Tank and CFM at 90 PSI 2.5 gallons and 3.0 SCFM (DEWALT); 5 gallons and 2.8 CFM (Limodot) 4.2 gallons and 4.2 CFM (MAC2400); 2.6 gallons and 3.3 CFM (MAC700) DEWALT, Limodot, Makita MAC2400, Makita MAC700

The table above is the general trade-off. The four listings below split two and two, so compare them on CFM, tank size, noise and warranty instead.

When oil lubricated is the better choice

  • Long shop sessions. The Makita listings describe oil lubricated as cooler running with less wear, which matters when the compressor cycles all day.
  • Cutting, grinding and spraying. The Makita listings state recommended uses of cutting, grinding and spraying, with 4.2 CFM at 90 PSI on the MAC2400 and 3.3 CFM on the MAC700.
  • Pump life. Cast iron cylinders and lower RPM, 1720 and 1730 on the Makitas, favor long pump life.

When oil free is the better choice

  • Low maintenance. No oil to buy or change; the DEWALT and Limodot listings both describe maintenance-free operation.
  • Quieter work. 68 dB on the Limodot title and 71.5 dBA on the DEWALT beat the 79 and 80 dB Makitas.
  • Grab and go. The DEWALT, stated at 36 lb in the bullets, and the Limodot with a wheels kit move around the shop.

Oil free vs oil lubricated air compressor: four picks, ranked

1. Makita MAC2400

The MAC2400 is an oil lubricated 2.5 HP compressor with a 4.2 gallon tank, 4.2 CFM at 90 PSI, a cast iron pump at 1730 RPM and 79 dB. It lists a roll-cage, a 4-pole motor at 12.3A, an automotive style air filter and a 1 Year Parts & Labor warranty. Who it suits: a shop that wants 4.2 CFM at 90 PSI for cutting, grinding and spraying.

2. DEWALT DWFP55130

The DEWALT is an oil free 1.1 HP compressor with a 2.5 gallon tank, 3.0 SCFM at 90 PSI, 200 max PSI and 71.5 dBA per ISO3744. It lists dual quick couplers, a roll cage, a 12A motor and a 1 year limited manufacturers warranty. Note a listing conflict on weight: the bullets state 36 lb, while the spec table lists a different weight in kilograms; this guide follows the bullets. Who it suits: trim and nailing with quiet, maintenance-free air.

3. Makita MAC700

The MAC700 is an oil lubricated 2.0 HP compressor with a 2.6 gallon tank, 3.3 CFM, a cast iron pump at 1720 RPM and 80 dB. It lists low amp draw and a 1 Year Parts & Labor warranty. Who it suits: a smaller oil lubricated pump for cutting, grinding and spraying.

4. Limodot Oil-Free

The Limodot is an oil free 1.2 HP compressor with a 5 gallon tank, 4 CFM at 40 PSI and 2.8 CFM at 90 PSI, at 68 dB. It lists a 25 ft hose, a 13-piece accessory kit, a wheels kit, an 80-second refill and 25-second recovery, and 120 PSI max. No warranty term is stated. Who it suits: the biggest tank here with a full accessory kit for nailing and inflation.

What to check before you buy

Match CFM to the tool: 4.2 at 90 PSI on the MAC2400, 3.0 SCFM on the DEWALT, 3.3 on the MAC700 and 2.8 at 90 PSI on the Limodot. Check noise against your shop: 68 to 71.5 dB on the oil free picks, 79 to 80 dB on the Makitas. The two Makitas and the DEWALT state 1 year warranties; the Limodot states no term. Drain the tank with the ball valve the DEWALT names, and keep the pump within the amps your circuit can feed: 12 to 12.3A on the 120V picks.

Compressor safety. Drain condensate regularly, keep the compressor clear of dust and sparks, and never exceed the max PSI stated: 200 on the DEWALT, 120 on the Limodot. Tank pressure is stored energy; treat it with respect.

Sizing the compressor to the job

Start with CFM at 90 PSI, the figure every listing here states: 4.2 on the MAC2400, 3.3 on the MAC700, 3.0 SCFM on the DEWALT and 2.8 on the Limodot. Tools that need higher CFM at 90 PSI sit at the top of that range; nailers and blow guns, both stated Limodot uses, run lower down. Then check the tank: 5 gallons on the Limodot, 4.2 on the MAC2400, 2.6 on the MAC700 and 2.5 on the DEWALT. A bigger tank means fewer pump cycles on intermittent tools, and the Limodot backs it with stated 80-second refill and 25-second recovery figures.

Check the electrics before you buy. The DEWALT draws 12A and the MAC2400 12.3A on 120V; the Makita listings note low amp draw reduces tripped breakers. For portability, the DEWALT is stated at 36 lb in the bullets, with a cord wrap, and stores vertical or horizontal, the Limodot ships a wheels kit, and the MAC2400 has a roll cage. On what ships in the box: the Limodot includes a 25 ft hose and 13-piece accessory kit, the MAC700 includes compressor oil and two 1/4 in quick couplers, the MAC2400 includes oil and a coupling, and the DEWALT has two couplers attached.

FAQ for welders

Is oil free or oil lubricated better for plasma cutting?

No listing here states a plasma cutting recommendation. The Makita listings describe oil lubricated pumps as cooler running with less wear. The DEWALT and Limodot listings describe oil free maintenance-free operation. Check your plasma cutter manual for its air requirements.

Which listing states the lowest noise?

The Limodot at 68 dB in the title, then the DEWALT at 71.5 dBA. The Makitas list 79 and 80 dB.

Which of these state a warranty?

The two Makitas state 1 Year Parts & Labor and the DEWALT states a 1 year limited manufacturers warranty. The Limodot states no term.

Which has the biggest tank?

The Limodot at 5 gallons. Then the MAC2400 at 4.2, and the MAC700 and DEWALT at 2.6 and 2.5 gallons.

Related: our pilot arc vs high frequency plasma cutter guide and our blowback start vs high frequency plasma cutter comparison.

More buying guides