Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Contact Start vs Pilot Arc Plasma Cutter: Which One Should You Buy?

Contact start and pilot arc plasma cutters differ in arc ignition, cut quality, consumable wear, and suitability for painted or expanded metal.

Contact Start vs Pilot Arc Plasma Cutter: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YESWELDER CUT-65DS PLUS Plasma CutterYESWELDER CUT-65DS PLUS Plasma Cutter9.7/10View on Amazon
  2. 2YESWELDER 60A Non-HF Plasma CutterYESWELDER 60A Non-HF Plasma Cutter9.6/10View on Amazon
  3. 3Plasma Cutter 55A, 110V/220V Plasma Cutter MachinePlasma Cutter 55A, 110V/220V Plasma Cutter Machine9.3/10View on Amazon

Verdict. A pilot arc plasma cutter is the right choice for cutting expanded metal, painted pipe, and rusty farm scrap without needing bare metal contact at every start. A contact start plasma cutter makes sense for clean sheet metal in a hobby shop where carrying an ultra-compact unit like the 8 lb Futelo example matters more than non-contact arc ignition.

When you are cutting rusty angle iron, slicing expanded metal grating, or trimming clean sheet metal on the fab table, choosing between a contact start vs pilot arc plasma cutter determines how cleanly your cut begins and how torch consumables hold up. This comparison puts the contact start Futelo CUT-55A against two pilot arc machines, the YESWELDER CUT-65DS PLUS and CUT-60DS PRO-1, based on what each manufacturer publishes.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The three machines

YESWELDER CUT-65DS PLUS Plasma Cutter

YESWELDER CUT-65DS PLUS Plasma Cutter

YESWELDER9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 65A dual-voltage pilot arc plasma cutter with an IPT40 torch, four cutting modes, ETL listing and a 2-year warranty.

Pros

  • 65A output with rated maximum cut of 1 inch at 220V and 5/8 inch at 110V
  • Non-touch pilot arc IPT40 torch cuts without contacting workpiece metal
  • Four functions in one unit including plate cutting, grid cutting, gouging and marking
  • ETL certified with IP21 protection and a written 2-year warranty

Cons

  • No duty cycle rating stated in the listing
  • No item weight or exterior dimensions published in the listing
  • No included accessories or box contents list stated in the listing
YESWELDER 60A Non-HF Plasma Cutter

YESWELDER 60A Non-HF Plasma Cutter

YESWELDER9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60A dual-voltage pilot arc plasma cutter with an IPT40 torch, digital display, built-in air filter, ETL listing and 1-year warranty.

Pros

  • 60A output with rated clean cut of 5/8 inch at 220V and 5/16 inch at 110V
  • Non-touch pilot arc IPT40 torch cuts without touching tips to workpiece
  • ETL certified with IP21 rating, overload protection and a 1-year warranty
  • Includes IPT40 torch, air filter regulator, air hose, ground clamp and power adapter

Cons

  • Listing gives model name as CUT-60DS PRO-1 but model number as CUT-65DS
  • No duty cycle rating stated in the listing
  • No weight published in the listing
  • Maximum cut on 110V is 1/2 inch compared to 5/8 inch on the 65DS PLUS
Plasma Cutter 55A, 110V/220V Plasma Cutter Machine

Plasma Cutter 55A, 110V/220V Plasma Cutter Machine

Futelo9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8 lb portable 55A contact start plasma cutter with 110V/220V capability, rear air regulator and adjustable post-flow.

Currently unavailableCheck price on Amazon

Pros

  • Lightweight design at 8 lb in bullets and 7.7 pounds in the specification table
  • Dual voltage 110V/220V with maximum cut of 3/4 inch at 55A on 220V
  • Equipped with rear-mounted air filter and manual pressure regulator with 1/4 inch NPT fitting
  • Adjustable post-flow cooling from 3 to 15 seconds with 2T and 4T torch control

Cons

  • Contact arc start requires touching torch tip to the metal to initiate arc
  • No ETL, UL or CSA safety certification stated in the listing
  • No warranty term is stated in the listing

Other welders and gear to compare

Side by side

YESWELDER CUT-65DS PLUS YESWELDER CUT-60DS PRO-1 Futelo CUT-55A
Gear Score 79 73 50
Arc ignition Pilot arc (blow-back, non-touch) Pilot arc (blow-back, non-touch) Contact arc start (tip touch)
Output range Up to 65A Up to 60A Up to 55A (35A at 110V)
Input voltage 110V/220V dual voltage 110V/220V dual voltage 110V/220V (table lists 110V)
Rated clean cut 5/16 in at 110V, 9/16 in at 220V 5/16 in at 110V, 5/8 in at 220V 1/2 in (iron, steel, aluminum, copper)
Rated max cut 5/8 in at 110V, 1 in at 220V 1/2 in at 110V, 63/64 in at 220V 1/2 in at 110V, 3/4 in at 220V
Torch IPT40 pilot arc torch IPT40 pilot arc torch Contact start torch
Operating modes Plate, grid cutting, gouging, marking Plate cutting, 2T/4T Plate cutting, 2T/4T
Air requirements Not stated Not stated Approx 60 PSI, 250 L/min, 1/4 in NPT
Weight Not stated Not stated 8 lb (bullets), 7.7 lb (table)
Duty cycle Not stated Not stated Not stated
Safety certification ETL certified, IP21 ETL certified, IP21 Not stated
Warranty 2 years 1 year Not stated

All specs here repeat what the maker rates and the listing prints, copied down 15 October 2026. Safety certifications and warranties are reported only where the listing states a verified standard or explicit duration.

Contact start vs pilot arc plasma cutter: how arc ignition differs

The defining difference between these two designs is how the cutting arc initiates. On a contact start machine like the Futelo CUT-55A, the operator must touch the torch tip directly against conductive metal to complete the electrical circuit and start the plasma arc. The Futelo listing claims its contact start makes it easier to start on painted or slightly rusty metal surfaces without high-frequency interference. In practice, because contact start depends on electrical continuity between the nozzle and the plate, non-conductive coatings like heavy paint or mill scale can prevent the arc from establishing until the tip contacts bare steel.

In contrast, both YESWELDER machines use a non-touch pilot arc with a blow-back start mechanism and an IPT40 torch. Internal air pressure moves an internal torch component away from the nozzle to establish a pilot arc inside the torch head without high-frequency interference. This allows the arc to transfer to the workpiece before the nozzle touches the plate. For a deeper look at blow-back torches, see our pilot arc vs blowback start explainer and our guide to plasma cutter types.

Cutting capacity and thickness

Cutting capacity varies across these units and between input voltages. The YESWELDER CUT-65DS PLUS rates clean cuts at 5/16 inch on 110V and 9/16 inch on 220V, with a maximum cut of 5/8 inch on 110V and 1 inch on 220V. The YESWELDER CUT-60DS PRO-1 lists clean cuts at 5/16 inch on 110V and 5/8 inch on 220V, with a maximum cut of 1/2 inch on 110V and 63/64 inch on 220V.

The Futelo CUT-55A listing claims a 1/2 inch clean cut on iron, steel, aluminum, and copper. For maximum cut thickness, the maker rates the unit at 1/2 inch (12mm) at 35A on 110V with 50 PSI, and 3/4 inch (18mm) at 55A on 220V with 65 PSI. On 220V power, the two YESWELDER listings state higher maximum cuts (1 inch and 63/64 inch) than the Futelo listing (3/4 inch). Check our plasma cutter amperage vs thickness chart for material planning.

Grating, paint, and rust performance

Surface conditions and workpiece geometry highlight why arc starting mechanisms matter in the shop. A contact start torch requires continuous electrical contact with the workpiece. Slicing through expanded metal or grating with a contact start machine causes the cutting arc to extinguish as the torch crosses open gaps, requiring the operator to re-strike the arc at each solid strand.

A pilot arc maintains an energized arc across gaps, allowing continuous cutting across mesh and grating. The YESWELDER CUT-65DS PLUS listing highlights dedicated grid cutting and gouging modes to maintain arc stability across perforated metal and wash out old weld beads. In addition, igniting above the workpiece lets the pilot arc burn through paint and rust without dragging the nozzle through debris, reducing spatter buildup; see our plasma cutter consumable guide for torch wear factors.

Air supply and torch controls

Compressed air delivery affects cut quality and consumable longevity on both styles of cutter. The Futelo CUT-55A listing provides detailed air parameters, specifying a rear air filter regulator with a 1/4 inch NPT quick-connect fitting, maintaining approximately 60 PSI with a 250 L/min flow rate. It includes adjustable post-flow cooling from 3 to 15 seconds (with 4 to 8 seconds recommended) and 2T/4T trigger control.

The YESWELDER CUT-60DS PRO-1 includes a rear air filter regulator, air hose, and a digital display showing air pressure, voltage, and current, with post-flow adjustable from 5 to 20 seconds (recommending 5 to 8 seconds). The CUT-65DS PLUS also features a digital display showing air pressure and 2T/4T controls, but its listing omits compressor flow rate and pressure requirements. For air system planning, see our guide on air compressors for plasma cutters.

Weight, build, and included accessories

Machine weight is published for only one unit in this comparison. The Futelo CUT-55A listing reports a weight of 8 lb in its bullets and 7.7 pounds in its specification table, with dimensions of 11.81 by 4.84 by 7.87 inches. Neither YESWELDER listing states a machine weight, so the listings leave that comparison incomplete. In addition, the Futelo spec table lists voltage as 110 volts, contradicting the 110V/220V dual voltage stated in its title and bullets, and lists only the plasma cutter as an included component.

The YESWELDER CUT-60DS PRO-1 listing publishes dimensions of 15.75 by 5.91 by 11.81 inches and includes an IPT40 torch, air regulator, air hose, ground clamp, and power adapter. Its listing displays an internal contradiction, naming the model CUT-60DS PRO-1 in the model name field and CUT-65DS in the model number and part number fields. The CUT-65DS PLUS listing leaves dimensions, weight, and box contents unstated.

Warranty and safety listings

Verified electrical standards and written warranty terms divide these listings. Both YESWELDER models state ETL certification and IP21 water protection ratings in their listings, confirming compliance with North American electrical standards. The CUT-65DS PLUS is backed by a written 2-year warranty with North American service support, while the CUT-60DS PRO-1 listing states a 1-year warranty.

The Futelo CUT-55A listing does not state a CSA, UL, or ETL safety certification, and it states no warranty term. When connecting equipment to shop power, third-party safety listings provide verified protection against electrical shock and fire hazards.

Choose a pilot arc plasma cutter if

  • You cut rusty steel, painted farm equipment, or salvage scrap regularly.
  • You need to cut expanded metal grating, wire mesh, or perforated sheet without the arc extinguishing.
  • You want higher stated cut capacity on 220V, with maximum cuts of 1 inch or 63/64 inch in these listings.
  • You require a verified ETL safety listing and a written 1-year or 2-year warranty.

Choose a contact start plasma cutter if

  • You cut clean, bare sheet metal where non-contact arc transfer is unnecessary.
  • You want an ultra-portable machine like the 8 lb Futelo example for light shop carry.
  • You need simple manual torch control for basic hobby cutting.
  • You do not require grid cutting modes, gouging, or non-contact starting.

Before You Strike an Arc

  • Verify whether your outlet supplies 110V or 220V power and ensure your machine plug adapter matches that circuit before turning on the power switch.
  • Inspect the rear air filter regulator bowl on arrival for shipping damage and ensure air fittings are sealed with thread sealant.
  • Check air pressure settings for your specific machine, noting that the Futelo model specifies approximately 60 PSI while YESWELDER units display pressure digitally.
  • Check IPT40 torch consumables on pilot arc units to confirm the electrode and nozzle are properly seated and undamaged before cutting.
  • Wear eye protection with the correct shade for plasma cutting; see our guide on what shade for plasma cutting.

FAQ for welders

What is the main difference between contact start and pilot arc plasma cutters?

A contact start torch requires physical contact between the torch tip and the conductive workpiece to strike the cutting arc. A pilot arc torch ignites an internal arc inside the torch head using blow-back air pressure, allowing the arc to jump to the workpiece without touching the plate. This non-contact ignition preserves nozzle orifices and allows cutting over painted or perforated metal.

Can a contact start plasma cutter cut through expanded metal or grating?

Cutting grating or expanded metal with a contact start torch is difficult because the arc extinguishes every time the torch crosses an open gap. The operator must physically touch the workpiece again to re-strike the arc at every metal strand. A pilot arc machine maintains an active arc across air gaps, making continuous cuts through mesh and grating possible.

Do pilot arc plasma cutters consume nozzles and electrodes faster?

Non-touch pilot arc cutting generally extends nozzle life by keeping the tip off the plate and away from molten blowback. However, firing a pilot arc in open air for extended periods without transferring to the workpiece will accelerate electrode wear. Both manufacturers recommend post-flow cooling (4 to 8 seconds on the Futelo listing, and 5 to 8 seconds on the YESWELDER listing) to extend consumable life.

Can you use a contact start plasma cutter on painted or rusty steel?

While the Futelo listing claims easier starting on painted or slightly rusty metal, contact start torches inherently require electrical conductivity between the nozzle and the workpiece to strike. Heavy paint, primer, and rust insulate the metal and prevent arc ignition until you grind a bare contact patch. Pilot arc torches ignite internally without touching the plate, allowing them to burn directly through surface rust and paint.

Do these plasma cutters require high-frequency start?

Neither system here uses high-frequency ignition. Both YESWELDER pilot arc models use blow-back start mechanisms, and the Futelo unit uses mechanical contact start. Both designs avoid high-frequency electrical interference, making them safe to run near computers, digital displays, and electronic shop equipment.

Related: plasma cutter types, pilot arc vs blowback start plasma cutter, plasma cutting consumables guide, best home hobby plasma cutter, and the plasma cutters hub.

Scoring, line by line

All three machines are scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
YESWELDER CUT-65DS PLUS 9.7 30 20 21 7 3
YESWELDER CUT-60DS PRO-1 9.6 28 19 20 7 2
Futelo CUT-55A 9.3 24 18 19 0 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.

More buying guides