Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Blind Rivet Sizes Chart for Metal Work

Blind rivet sizes run from 3/32 inch to 1/4 inch in diameter in the kits listed here, and the length after the diameter tells you how much material the rivet can close.

Blind Rivet Sizes Chart for Metal Work
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1WensilonWensilon9.7/10View on Amazon
  2. 29.7/10View on Amazon
  3. 3320Pcs 1/8 Pop Rivets Assortment Kit; Aluminum Blind Rivet320Pcs 1/8 Pop Rivets Assortment Kit; Aluminum Blind Rivet9.7/10View on Amazon

Sheets of steel meet on the bench, and you can only reach them from the working side. A bolt needs access to the far face, and a weld needs a machine, gas and a steady hand. A blind rivet closes the joint from the working side alone, and the whole choice comes down to blind rivet sizes: the diameter that fits the hole and the length that closes the stack. This guide reads the sizes the way the kits state them, so you can match a rivet to a joint without guessing.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Blind rivet sizes: diameter, then length

Every blind rivet size in the kits is written as diameter by length, in inches. A rivet listed as 3/16 by 1/2 inch has a 3/16 inch body and a 1/2 inch shank: the diameter decides which hole it fits, and the length decides how much material it can close. The kits listed here carry 5 diameters, 3/32, 1/8, 5/32, 3/16 and 1/4 inch, with lengths from 1/4 inch to 1 inch. Washers in the same kits come in matching sizes, 3/32 through 1/4 inch.

A blind rivet sets from a single side, which is why the kits call it a pop rivet and a blind rivet in the same breath. The mandrel pulls through the body, the blind end swells behind the far sheet, and the stem snaps off flush. All the kits here pair with a rivet gun. For the tool that sets them, see rivet gun uses.

Side by side

Lengths in the kits Matching washer size Material What the kits show
3/32 inch 1/4 and 5/16 inch 3/32 inch Aluminum with a steel mandrel smseace lists 100 pieces in each length
1/8 inch 1/4, 5/16, 3/8 and 1/2 inch 1/8 inch Aluminum, or 304 stainless steel ALLWIN lists 40 pieces of 1/8 by 1/4 inch
5/32 inch 5/16, 3/8 and 1/2 inch 5/32 inch Aluminum, or 304 stainless steel INCLY lists 45 pieces of 5/32 by 3/8 inch
3/16 inch 1/4, 5/16, 3/8, 1/2, 5/8, 3/4 and 1 inch 3/16 inch Aluminum, or 304 stainless steel ZQZ lists 43 pieces of 3/16 by 5/16 inch
1/4 inch 3/8, 1/2, 5/8 and 1 inch 1/4 inch Aluminum, or 304 stainless steel SATANTECH lists 4 pieces of 1/4 by 1 inch

Read the chart across a row to see what each diameter brings. The 3/32 inch row has the fewest lengths, 1/4 and 5/16 inch only, while the 3/16 inch row carries the widest spread of lengths in the kits. Washer sizes track the diameters size for size in the INCLY kit (on Amazon): 100 washers in 3/32 inch, 175 in 1/8 inch, 80 in 5/32 inch, 120 in 3/16 inch and 25 in 1/4 inch.

What the diameter decides

The diameter decides the hole. Drill the hole to match the rivet body, and the rivet fills it without slop. A 1/4 inch rivet needs a larger hole than a 3/32 inch rivet, and it also needs more room around the joint for the head to sit flat. The 3/16 inch diameter appears in every kit listed here, which makes it the easiest size to keep on hand.

When the hole is oversized, a washer under the head spreads the load. The INCLY kit pairs washers with every diameter it carries, and the kit states its washers prevent pull-out on oversized holes. A large flange head does the same job without a washer; the smseace kit states its wider head gives a bigger gripping surface for softer materials.

What the length decides

The length is the shank behind the head, and it has to pass through the stack and leave enough shank to form the blind head on the far side. A length that is too short never forms a head, and a length that is too long leaves a loose joint that rattles. The 3/32 inch rivets come in 1/4 and 5/16 inch lengths, while 3/16 inch rivets run from 1/4 inch to 1 inch.

When you match a length, add the thickness of every layer in the stack, then pick a rivet length that covers it with a little shank to spare. The INCLY, ZQZ 970, ZQZ 630 and smseace 1500 kits carry 14 or 15 sizes, so you can step up a size when the stack grows.

Washers and large flange heads

A standard dome head spreads its load over a small ring. Where the material is soft or the hole is worn, the head can pull through. The INCLY kit includes 500 washers in 5 sizes, and the ZQZ 970-piece kit includes 330 washers in 4 sizes.

Aluminum or stainless steel

Most of the kits here are aluminum rivets with a steel mandrel. The makers state corrosion resistance, rust resistance and a long service life for the aluminum kits, and the same words for the 304 stainless steel kits. SATANTECH states its 304 stainless steel is considerably harder than aluminum, with stronger anti-rust and abrasion resistance.

The ZQZ 680-piece kit and the SATANTECH 450-piece kit are the 304 stainless steel kits in the list. Each material is listed for indoor and outdoor use, so the choice comes down to the harder stainless body against the aluminum body the other kits list. See our steel vs aluminum blind rivets comparison for the material choice in full.

How to pick a size for a sheet metal joint

Pick in this order, and check each step against the kit before you order.

  • Start with the hole. Match the rivet diameter to the hole you drilled, and keep the hole round and clean so the body fills it.
  • Stack the layers. Add the thickness of every layer in the joint, then pick a length that passes through the full stack with shank left to form the head.
  • Decide on a washer. Where the material is soft or the hole is worn, back the head with a washer in the matching size or reach for a large flange rivet.
  • Match the material. Aluminum suits general shop work, and the 304 stainless steel kits suit joints where the maker states the harder body.

Our best rivet gun kit guide covers the guns that set these sizes, and the best blind rivets for stainless steel roundup scores the stainless kits. A rivet gun pulls the mandrel and snaps the stem, so buy or borrow the gun before the kit, not after.

FAQ for welders

What does 3/16 by 1/2 inch mean on a blind rivet?

The first number is the diameter of the rivet body, and the number after it is the length of the shank behind the head. A 3/16 by 1/2 inch rivet has a 3/16 inch body and a 1/2 inch shank. Match the diameter to the hole and the length to the stack it has to close.

Do blind rivets need washers?

Not always. A washer backs the head where the hole is oversized or the material is soft, and the INCLY kit states its washers prevent pull-out on oversized holes. The INCLY, ZQZ 970 and SATANTECH kits carry washers in the same sizes as their rivets, from 3/32 inch through 1/4 inch.

Are stainless steel blind rivets harder than aluminum ones?

SATANTECH states its 304 stainless steel rivets are considerably harder than aluminum, with stronger anti-rust and abrasion resistance. The aluminum kits state corrosion resistance and a long service life in the same words. The kits list each material for indoor and outdoor use, so the harder body is the difference the maker states, not the setting.

What size blind rivet do I need for sheet metal?

Match the diameter to the hole you drilled, then pick a length that passes through the full stack with enough shank left to form the blind head. The 3/16 inch diameter appears in every kit listed here, and its lengths run from 1/4 inch to 1 inch, which gives the widest choice of lengths in the kits.

How many rivets come in an assortment kit?

The kits listed here run from 140 rivets in the ZQZ 3/16 inch kit to 900 rivets in the smseace 1500-piece kit, with 200, 225, 340, 500, 630, 640 and 800 rivet kits in between. Washer counts run from 225 pieces in the SATANTECH kit (on Amazon) to 500 pieces in the INCLY kit.

Related: metal fab tools, best rivet gun for metal, types of rivet nuts, and blind rivet pliers vs rivet gun.

More buying guides