Best Step Drill Bit Under 15 (2026)
Five step drill bits under $15 compared by step count and size range, point angle, shank type, coating and what each listing states, with table errors noted.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAleric 3-Pc Step Bit Set9.4/10View on Amazon - 2
Best Single BitNEIKO 10185A Step Bit9.4/10View on Amazon - 3
Biggest HolesMACXCOIP Step Bit 1-3/89.4/10View on Amazon - 4
With a BagIRONANT 3-Pc Step Bit Set9.4/10View on Amazon - 5
Metric PickShallho 4-22mm Step Bit9.3/10View on Amazon
The best step drill bit under 15 earns its drawer space: one bit that drills and deburrs a range of hole sizes in sheet metal without swapping. This guide compares five by step count and size range, point angle, shank, coating and what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same.
Quick picks
- Best Overall Aleric 3-Pc Step Bit Set: Three bits covering 28 sizes from 1/8 in to 3/4 in, titanium-coated HSS with a 135 degree split point and tri-flat shanks. Check price on Amazon
- Best Single Bit NEIKO 10185A Step Bit: A single 12-step bit from 3/16 in to 7/8 in in #4241 HSS with titanium nitride coating and a 3/8 in tri-flat shank. Check price on Amazon
- Biggest Holes MACXCOIP Step Bit 1-3/8: Ten steps from 3/16 in to 1-3/8 in with a hex shank and a laser-engraved size scale. Check price on Amazon
- With a Bag IRONANT 3-Pc Step Bit Set: Three bits, 28 sizes, in a portable bag; 118 degree split point, not recommended for stainless steel or wood. Check price on Amazon
- Metric Pick Shallho 4-22mm Step Bit: A single 4 to 22 mm bit with a 1/4 in hex shank, listed for impact-rated power tools. Check price on Amazon
The machines

Aleric Step Drill Bit Set - Titanium Coated
A 3-piece titanium-coated HSS step bit set covering 28 sizes from 1/8 in to 3/4 in, with 135 degree split points and tri-flat shanks.
Pros
- 28 sizes across 3 bits, 1/8 in to 3/4 in
- Titanium-coated HSS with 135 degree split point
- Tri-flat shanks fit impact drill chucks
- Two-flute design for faster, smoother drilling
Cons
- Table lists stainless steel as the material against HSS in the title
- No warranty term stated
- Max size 3/4 in, smaller than the NEIKO and MACXCOIP
- Bullets mention home DIY more than shop metalwork

NEIKO 10185A Step Drill Bit
A single 12-step bit in #4241 HSS with titanium nitride coating, 3/16 in to 7/8 in, with a 135 degree split point and 3/8 in tri-flat shank.
Pros
- 12 steps in one bit, 3/16 in to 7/8 in
- #4241 HSS with titanium nitride coating
- 135 degree split point with two-flute straight groove
- 3/8 in tri-flat shank runs concentrically
Cons
- Bullets start sizes at 1/16 in against 3/16 in in the title
- Table says straight shank against tri-flat in the title
- Table lists 1.13 in cutting diameter against 7/8 in maximum
- No warranty term stated

3PCS HSS Step Drill Bit Set for Metal Titanium
A 3-piece titanium-coated HSS step bit set covering 28 sizes from 1/8 in to 3/4 in, with a 118 degree split point and a portable bag.
Pros
- 28 sizes across 3 bits, 1/8 in to 3/4 in
- Portable bag included for storage
- 118 degree split point with dual-flute design
- Hex shanks fit standard chucks
Cons
- Not recommended for stainless steel or wood
- Table lists straight flute type against dual-flute bullets
- No warranty term stated
- Max size 3/4 in, smaller than the NEIKO and MACXCOIP

3/16" to 1-3/8" HSS Step Drill Bit Set Hex Shank
A single 10-step bit from 3/16 in to 1-3/8 in in titanium-coated HSS with a hex shank and laser-engraved size scale.
Pros
- 10 steps to 1-3/8 in, the largest range here
- Hex shank with wobble-free design
- Laser-engraved size scale
- Rated for steel sheet up to 0.2 in
Cons
- Table lists 1.25 in cutting diameter against 1-3/8 in in the title
- Table lists 10 pieces against a single bit
- Single bit only, no set
- No warranty term stated

4-22 mm Titanium Coated Spiral Grooved Step Drill
A single 4 to 22 mm step bit in HSS 4241 with titanium coating, a 135 degree X-type split point and a 1/4 in hex shank.
Pros
- 10 steps, 4 to 22 mm, the metric pick
- 1/4 in hex shank listed for impact-rated tools
- 135 degree X-type split point
- High steps give a positive stop against overshooting
Cons
- Smallest range here at 22 mm max
- Table flute field just repeats the part number
- No warranty term stated
- Single bit only
Other welders and gear to compare
NEIKO 10194A Step Drill BitCheck price on Amazon
NEIKO 10182A Titanium Step Drill BitCheck price on Amazon
NEIKO 10184A Step Drill BitCheck price on Amazon
NEIKO 10174A Step Drill BitCheck price on Amazon
3 PCS Step Drill Bit SetCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Sizes | Max diameter | Point | Shank | In the box |
|---|---|---|---|---|---|---|
| Aleric 3-Pc Step Bit Set | 9.4/10 | 28 sizes across 3 bits | 3/4 in | 135 degree split point | Tri-flat | 3 bits |
| NEIKO 10185A Step Bit | 9.4/10 | 12 steps | 7/8 in (title) | 135 degree split point | 3/8 in tri-flat | 1 bit |
| IRONANT 3-Pc Step Bit Set | 9.4/10 | 28 sizes across 3 bits | 3/4 in | 118 degree split point | Hex | 3 bits, portable bag |
| MACXCOIP Step Bit 1-3/8 | 9.4/10 | 10 steps | 1-3/8 in (title); 1.25 in (table) | Not stated | Hex | 1 bit |
| Shallho 4-22mm Step Bit | 9.3/10 | 10 steps, 4 to 22 mm | 22 mm | 135 degree X-type split point | 1/4 in hex | 1 bit |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 October 2026. Where a listing states a figure two ways, the table shows both.
Buying guide: the best step drill bit under 15
Step count and size range
Step count runs from 10 (MACXCOIP, Shallho) to 12 (NEIKO), with the 3-piece sets covering 28 sizes each (Aleric, IRONANT). Size ranges: 3/16 in to 7/8 in on the NEIKO per the title, 1/8 in to 3/4 in on the Aleric and IRONANT sets, 3/16 in to 1-3/8 in on the MACXCOIP, and 4 to 22 mm on the Shallho. Pick the range that covers the holes you actually drill; the biggest bit is only useful if you need 1-3/8 in holes.
Point angle and flutes
Three listings state a 135 degree split point (NEIKO, Aleric, Shallho) and one states 118 degrees (IRONANT). The split point is the self-centering tip the listings credit for no-walk starts. Two-flute designs are stated across the picks; the NEIKO adds a straight two-flute groove that pulls chips up and out, and the MACXCOIP states staggered cutting teeth for smoother holes.
Shank types
Shanks here: 3/8 in tri-flat on the NEIKO, tri-flat on the Aleric, hex on the MACXCOIP and IRONANT, and 1/4 in hex on the Shallho. Tri-flat shanks grip drill chucks with less wobble per the NEIKO listing; the Shallho 1/4 in hex shank is the one listed for impact-rated power tools. Match the shank to the tool you own.
What each bit is rated to cut
Materials stated per listing: the NEIKO lists plastic, aluminum, wood, copper, stainless steel and sheet metal; the Aleric lists plastic, aluminum, wood board and copper; the MACXCOIP lists steel sheets up to 0.2 in plus acrylic, PVC and wooden boards; the IRONANT lists plastic, aluminum, iron and sheet metal but is not recommended for stainless steel or wood; the Shallho lists wood, plastic, sheet metal and general maintenance work. Match the bit to your metal: the NEIKO is the only one here whose listing names stainless steel as a surface.
What the spec tables get wrong
Read the tables with care. The NEIKO table lists a straight shank against the tri-flat shank in the title and bullets, a 1.13 in cutting diameter against 7/8 in maximum, and the bullets start sizes at 1/16 in against 3/16 in in the title. The MACXCOIP table lists a 1.25 in cutting diameter against 1-3/8 in in the title and 10 pieces against a single bit. The Aleric table lists stainless steel as the material against HSS in the title and bullets. In every case, trust the title and bullets.
For twist bits instead, see our best drill bits for steel.
Drilling safety. Step bits grab less than twist bits, but sheet metal still spins. Clamp the work, wear eye protection, and keep gloves and sleeves clear of the chuck. Deburr both sides of the hole; a step bit deburrs as it cuts, but the edge is still sharp.
Before You Strike an Arc
- Check the shank against your drill: 3/8 in tri-flat on the NEIKO, tri-flat on the Aleric, hex on the MACXCOIP and IRONANT, 1/4 in hex on the Shallho.
- Match the bit to the metal: the IRONANT is not recommended for stainless steel or wood; the MACXCOIP lists steel sheet up to 0.2 in.
- Confirm the size range on arrival: the NEIKO bullets list sizes from 1/16 in while the title starts at 3/16 in.
- A drop of cutting oil and moderate speed keep titanium-coated HSS cutting longer in steel.
FAQ for welders
What is a step drill bit used for?
Drilling and deburring multiple hole sizes in sheet metal, plastic, aluminum and wood with one bit. Each step cuts a larger diameter, so one bit replaces a set of twist bits for thin stock.
What does the point angle mean?
The NEIKO, Aleric and Shallho state a 135 degree split point; the IRONANT states 118 degrees. A split point centers the bit so it does not walk, and the listings claim faster starts and cleaner holes.
Can I use a step drill bit in an impact driver?
The Shallho 1/4 in hex shank is listed for impact-rated power tools. Tri-flat and hex shanks suit drill chucks and drill presses; check the shank against your tool before the first hole.
How thick a material can a step bit drill?
The MACXCOIP lists steel sheet up to 0.2 in and acrylic, PVC and wood up to 0.2 in. Step bits are for sheet and thin stock, not thick plate.
Why do listings disagree with their own tables?
It happens. The NEIKO bullets start sizes at 1/16 in while the title starts at 3/16 in, and the MACXCOIP table lists a 1.25 in cutting diameter against 1-3/8 in in the title. Trust the title and bullets.
Related: the best step drill bit for sheet metal, the best drill bits for steel, the cobalt vs HSS drill bits for steel and our metal fab tools hub.
Scoring, line by line
Each bit is scored on performance, build, value, safety and warranty, using only what the listing publishes. A spec the listing does not publish scores nothing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Aleric 3-Pc Step Bit Set | 9.4 | 29 | 19 | 20 | 0 | 0 |
| NEIKO 10185A Step Bit | 9.4 | 29 | 20 | 18 | 0 | 0 |
| IRONANT 3-Pc Step Bit Set | 9.4 | 28 | 19 | 19 | 0 | 0 |
| MACXCOIP Step Bit 1-3/8 | 9.4 | 29 | 18 | 18 | 0 | 0 |
| Shallho 4-22mm Step Bit | 9.3 | 27 | 19 | 18 | 0 | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.




