Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Small Bench Vise (2026): 3 Compared

Small bench vises compared on jaw size, mounting, clamping force and swivel.

Best Small Bench Vise (2026): 3 Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1MYTEC 3.3in Bench ViseQuick ReleaseMYTEC 3.3in Bench Vise9.5/10View on Amazon
  2. 2Olympia Tools 38-604Cast Iron AnvilOlympia Tools 38-6049.5/10View on Amazon
  3. 3STEINBRUECKE 3.3in ViseDual MountSTEINBRUECKE 3.3in Vise9.5/10View on Amazon

A full-size vise is overkill for small stock, and pliers are not a vise. Small work vibrates, slips and burns fingers when it is held by hand, and a drill bit walks on a part that is not clamped. A small bench vise solves that with a jaw, a screw and a base, in a footprint that leaves room on the bench for the actual work. A small bench vise holds little parts still for drilling, filing and gluing, without eating the whole bench. The best small bench vise clamps to the bench or bolts down, opens wide enough for real work, and swivels to the angle you need.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Quick picks

  • Quick Release MYTEC 3.3in Bench Vise: 1350 lbs clamping force with quick release and 360-degree swivel. Check price on Amazon
  • Cast Iron Anvil Olympia Tools 38-604: 4-inch cast iron vise with anvil, pipe jaws and 270-degree swivel. Check price on Amazon
  • Dual Mount STEINBRUECKE 3.3in Vise: 3.3-inch dual-purpose vise with 360-degree swivel and hardened jaws. Check price on Amazon

The machines

MYTEC Bench Vise or Table Vise

MYTEC Bench Vise or Table Vise

MYTEC9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3.3-inch dual-purpose vise with 1350 lbs clamping force, a quick release button, 360-degree swivel and clamp-on or screw mounting.

Pros

  • 1350 lbs clamping force stated
  • Quick release one-click position
  • 360-degree swivel base
  • Clamp-on or screw mounting

Cons

  • No warranty term stated
  • 5 pounds to move
  • 2.44 in opening limits stock
  • Black finish shows dust
Olympia Tools 38-604 Bench Vise, Workshop Series

Olympia Tools 38-604 Bench Vise, Workshop Series

Olympia Tools9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-inch bench vise with a 270-degree swivel base, polished anvil, pipe jaws and a reinforced 4-lug base, in cast iron.

Pros

  • 4-inch jaw, widest jaw here
  • Polished anvil and pipe jaws
  • 270-degree swivel with lock
  • Reinforced 4-lug base

Cons

  • No usable warranty term
  • 5.1 pounds to move
  • Gray finish, industrial look
  • 4-lug base needs bench space
Dual-Purpose Combined Universal Vise 3.3"

Dual-Purpose Combined Universal Vise 3.3"

STEINBRÜCKE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3.3-inch dual-purpose vise with 360-degree swivel, clamp-on or screw mounting and hardened jaws, in high-grade cast steel.

Pros

  • 360-degree swivel base
  • Clamp-on or screw mounting
  • Hardened hammered jaws
  • One-click quick release

Cons

  • No warranty term stated
  • 2.5 in opening limits stock
  • Black finish shows dust
  • Light work stated use

Other welders and gear to compare

Spec sheet comparison

Vise Jaw Opening Mount Swivel
MYTEC 3.3 in 2.44 in Clamp or screw 360 deg
Olympia 38-604 4-inch Not stated Bolt-down 270 deg
STEINBRUECKE 3.3 in 2.5 in Clamp or screw 360 deg

22 October 2026

Buying guide: the best small bench vise

Jaw size and opening

The Olympia Tools 38-604 has the widest jaw here at 4 inches, with an 11.02 by 5.51 by 5.91 in body. The MYTEC and STEINBRÜCKE both have a 3.3-inch jaw width, with maximum openings of 2.44 and 2.5 inches. Match the vise to the work: a 4-inch jaw for general shop tasks, a 3.3-inch jaw for smaller stock. The jaw width sets the widest part you can hold squarely; the opening sets the thickest. Note the gap between the two: the MYTEC 3.3-inch jaw opens to 2.44 inches and the STEINBRUECKE 3.3-inch jaw to 2.5 inches.

Clamp-on or bolt-down

The MYTEC and STEINBRÜCKE are dual-purpose: screw them firmly to the workbench or clamp them on, with a base clamping range to 4 inches for various bench thicknesses. The Olympia bolts to the bench with a heavy reinforced 4-lug base. A clamp-on vise moves between benches; a bolt-down vise never walks. The MYTEC and STEINBRUECKE give both options, so one vise serves the home bench and the portable work table.

Clamping force and build

The MYTEC states a 1350 lbs working maximum clamping force in high-grade cast steel with hardened, hammered jaws. The Olympia and STEINBRÜCKE state 1500 pounds tensile strength in cast iron and cast steel. The MYTEC 1350 lbs figure is a working maximum clamping force, while the Olympia and STEINBRUECKE 1500 pounds figures are tensile strength of the material: different measurements, so compare them as rough peers, not exact rivals. The MYTEC hardened and hammered jaws add grip for the same reason the Olympia jaw faces are replaceable hardened steel: jaws are the wearing part.

Swivel and extras

The MYTEC and STEINBRÜCKE rotate 360 degrees on swivel bases, and the MYTEC adds a quick release button for one-click positioning. The Olympia swivels 270 degrees with a swivel lock lever, plus a polished anvil, anvil horn and permanent pipe jaws. An anvil turns the vise into a shaping station; pipe jaws hold round stock. The Olympia permanent pipe jaws grip pipe and tube without crushing, and the anvil horn shapes curves. The MYTEC multi-functional jaws add 10 screw holes and 4 clamping posts for delicate irregular parts, with two jaw washers for protecting delicate parts.

Weight and bench space

The MYTEC is 5 pounds and the Olympia 5.1 pounds, bench fixtures rather than travelers. The MYTEC body measures 7.32 by 5.63 by 4.41 inches and the Olympia 11.02 by 5.51 by 5.91 inches, so the Olympia needs the most bench. For a dedicated metalworking bench, the bigger vises earn their footprint.

Warranty

None of the listings states a usable warranty term. The Olympia warranty field contains only an email address, which is not a term, so it scores zero like the rest.

[wgl_safety kind=”tool”]

FAQ for welders

What size bench vise do I need?

For general shop work, the 4-inch Olympia. For smaller stock, the 3.3-inch MYTEC or STEINBRUECKE, with openings of 2.44 and 2.5 inches.

Clamp-on or bolt-down vise?

Clamp-on (MYTEC, STEINBRUECKE) moves between benches and removes fast. Bolt-down (Olympia) stays put under heavy work.

How much clamping force do I need?

For light work, the 3.3-inch vises are enough. For metalwork, the MYTEC states 1350 lbs working clamping force and the Olympia and STEINBRUECKE state 1500 pounds tensile strength.

Which vise swivels 360 degrees?

The MYTEC and STEINBRÜCKE both state 360-degree rotation. The Olympia states 270 degrees.

Which small vise has an anvil?

The Olympia has a polished anvil and anvil horn.

Scoring, line by line

The Gear Score weighs performance, build, value, safety and warranty. Performance means stated clamping force and jaw opening against the size class. None of the listings states a usable warranty term, so all score zero there.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
MYTEC 3.3in Bench Vise 9.5 27 20 19 n/a 0
Olympia Tools 38-604 9.5 26 20 19 n/a 0
STEINBRUECKE 3.3in Vise 9.5 26 20 19 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

More welding guides

Also see our bench vise vs welding vise. Also see our welding vise vs welding clamp. Also see our types of welding clamps. Also see our toggle clamp vs c clamp.

More from WeldGearLab: welding tables and carts.

More buying guides

Metal Fab Tools ·

Bench Vise Types: Which One to Buy

Swivel-base, fixed-base and clamp-on bench vises compared, with jaw widths, clamping force and mounting explained.