Best Bench Vise for Farm Shop (2026): 5 Vises Scored for the Shop
Five bench vises scored for farm shop work: the Wilton WS5 takes best overall with pinch point guards and a lifetime warranty, followed by the Wilton 675U utility pick.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallWilton WS5 Vise9.6/10View on Amazon - 2
Utility PickWilton 675U Vise9.6/10View on Amazon - 3
Big JawVEVOR 6.5 in Vise9.6/10View on Amazon - 4
Rotating HeadForward DT150B Vise9.6/10View on Amazon
A farm shop vise lives a hard life: breaking rusted bolts loose, holding pipe for cutting, and taking hammer work on the anvil. This guide to the best bench vise for farm shop work scores five bench vises on Performance, Build, Value, Safety and Warranty, then matches each one to the farm shop work it fits best.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Wilton WS5 Vise: 5 in vise with pinch point guards and a lifetime warranty. Check price on Amazon
- Utility Pick Wilton 675U Vise: 5-1/2 in vise with dual lock-downs and lifetime warranty. Check price on Amazon
- Big Jaw VEVOR 6.5 in Vise: 6.5 in jaws with 9.3 in reverse opening and mounting kit included. Check price on Amazon
- Rotating Head Forward DT150B Vise: 6 in vise with 360-degree rotating head and 6,500 lbs of force. Check price on Amazon
The machines

Wilton Shop Bench Vise, 5" Jaw Width
Wilton's WS5 is a 5 in shop bench vise in 60,000 PSI ductile iron with a 360-degree swivel base, rubber pinch point safety guards and a lifetime warranty.
Pros
- 60,000 PSI ductile iron body built for rugged use
- Rubber pinch point safety guards stated
- 360-degree swivel base with double lockdowns
- Lifetime warranty description stated
Cons
- 5 in jaw is smaller than the 6 in plus options here
- 28.2 lb weight needs a stout bench
- No clamping force figure stated
- Replaceable jaws add a future parts cost

Wilton Utility Bench Vise, 5-1/2" Jaw Width
Wilton's 675U utility vise pairs a 5-1/2 in jaw with dual lock-downs, a 360-degree swivel base and a lifetime warranty for general shop and farm use.
Pros
- 5-1/2 in jaw width for wider workpieces
- Dual lock-downs on a 360-degree swivel base
- Replaceable hardened steel jaws with serrated pattern
- Lifetime warranty against manufacturing defects
Cons
- No clamping force figure stated
- 25.5 lb weight still needs solid mounting
- Powder coat will chip at high-wear points

VEVOR Bench Vise 6.5" Jaw Width Multipurpose
VEVOR's 6.5 in bench vise brings the widest jaws here, a 9.3 in reverse opening, 4496 lbs of clamping force and a mounting kit with magnetic jaw pads.
Pros
- 6.5 in jaw width, the widest of the five
- 9.3 in reverse opening for long workpieces
- 4496 lbs of clamping force stated
- Mounting bolts, nuts and magnetic jaw pads included
Cons
- Listing states no warranty term
- 27 lb weight with a wide footprint
- Powder coat finish can scratch on rough handling
- Magnetic pads are an extra part to keep track of

Forward DT150B 6 Inch Heavy Duty Bench Vise
Forward's DT150B is a 6 in bench vise with a 360-degree rotating head, 6,500 lbs of clamping force and 3 sets of jaws for flat stock, pipe and V work.
Pros
- 360-degree rotating head plus swivel base for any angle
- 6,500 lbs of clamping force stated
- 3 jaw sets: microgroove top jaws, pipe jaws, V-jaws
- Large reinforced anvil for grinding and tapping
Cons
- Listing states no warranty term
- 42 lb weight is the heaviest here
- 2 5/8 in throat is shallower than the others
- Three jaw sets mean more parts to store

Forward CR50A 5.5 Inch Bench Vise Heavy Duty
Forward's CR50A is a 5.5 in heavy-duty bench vise with 7,700 lbs of clamping force, a 210-degree swivel base and pipe jaws for 1/2 in to 3 1/2 in pipe.
Pros
- 7,700 lbs of clamping force, the highest stated here
- 5.5 in jaw with 6 in max opening
- Built-in pipe jaws for 1/2 in to 3 1/2 in pipe
- Large reinforced anvil for grinding and tapping
Cons
- Listing states no warranty term
- 210-degree swivel is less than full rotation
- No weight stated for bench planning
- Two jaw sets only, no V-jaws
Other welders and gear to compare
VEVOR Bench ViseCheck price on Amazon
AV Steel 4-1/2" Bench Vise with 240° Flexible Swivel LockingCheck price on Amazon
Wilton Utility Bench ViseCheck price on Amazon
Wilton shop bench viseCheck price on Amazon
MYTEC 2-In-1 Bench Vise Heavy Duty for WorkbenchCheck price on Amazon
How to choose the best bench vise for farm shop work
Start with jaw width and opening. For farm shop work the picks here run from a 5 in jaw to a 6.5 in jaw, and wider jaws grip big stock without tipping the work. Check the clamping force figure too: the listings here state from 4496 lbs up to 7,700 lbs, and higher force means the vise holds when you lean into a breaker bar.
Look at the swivel base next. A 360-degree swivel base with lockdowns lets you position long or awkward workpieces without unbolting the vise, while a 210-degree base still covers most angles. Pipe jaws matter on the farm: built-in pipe jaws that handle 1/2 in to 3 1/2 in pipe save you from improvising with the flat jaws.
Safety in this category is about guards and lockdowns: rubber pinch point safety guards protect your hands, and solid lockdowns keep the workpiece from shifting under load. Finally, check the warranty: two of these listings state a lifetime term, the others state none, and a vise is a buy-it-once tool.
What the five picks cover
The Wilton WS5 is the best overall pick, with 60,000 PSI ductile iron, pinch point guards and a lifetime warranty. The Wilton 675U is the utility value pick with a 5-1/2 in jaw and the same lifetime backing. The VEVOR 6.5 in vise brings the widest jaws and a 9.3 in reverse opening, the Forward DT150B adds a 360-degree rotating head with three jaw sets, and the Forward CR50A leads on clamping force at 7,700 lbs.
Spec sheet comparison
| Model | Gear Score | Jaw | Opening | Swivel | Clamping | Weight | Warranty |
|---|---|---|---|---|---|---|---|
| Wilton WS5 Vise | 9.6/10 | 5 in | 5 in | 360-degree | Not stated | 28.2 lb | Lifetime |
| Wilton 675U Vise | 9.6/10 | 5-1/2 in | 5 in | 360-degree | Not stated | 25.5 lb | Lifetime |
| VEVOR 6.5 in Vise | 9.6/10 | 6.5 in | 6.5 in / 9.3 in reverse | 360-degree | 4496 lbs | 27 lb | Not stated |
| Forward DT150B Vise | 9.6/10 | 6 in | 5 in | 360-degree head + base | 6,500 lbs | 42 lb | Not stated |
| Forward CR50A Vise | 9.6/10 | 5.5 in | 6 in | 210-degree | 7,700 lbs | Not stated | Not stated |
21 October 2026
Scoring, line by line
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Wilton WS5 Vise | 9.6 | 28 | 22 | 20 | 5 | 5 |
| Wilton 675U Vise | 9.6 | 28 | 21 | 20 | 4 | 5 |
| VEVOR 6.5 in Vise | 9.6 | 32 | 21 | 22 | 4 | 0 |
| Forward DT150B Vise | 9.6 | 30 | 21 | 21 | 3 | 0 |
| Forward CR50A Vise | 9.6 | 30 | 21 | 21 | 3 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.
Which vise fits your farm shop
If you want the vise that lasts, the Wilton WS5 is the pick: 60,000 PSI ductile iron, rubber pinch point safety guards and a lifetime warranty. If you want the same Wilton backing with a wider jaw, the 675U gives you 5-1/2 in of jaw and dual lock-downs, though its spec table disagrees with the title on the exact width.
If you need the biggest jaws, the VEVOR 6.5 in vise opens to 9.3 in in reverse and ships with its mounting kit. If you work at odd angles, the Forward DT150B’s rotating head and three jaw sets cover flat stock, pipe and V work. And if raw grip is the job, the Forward CR50A’s 7,700 lbs of clamping force is the highest figure here.
For related shop comparisons, see [bench vise vs welding vise](/bench-vise-vs-welding-vise/) and our [best bench vise for metal work](/best-bench-vise-for-metal-work/) roundup.
[wgl_safety kind=”tool”]
FAQ
What size bench vise does a farm shop need?
The picks here run from 5 in to 6.5 in. Match the jaw to the biggest stock you hold regularly, and check the max opening too: the VEVOR opens to 9.3 in in reverse.
How much clamping force is enough?
The listings here state from 4496 lbs to 7,700 lbs. More force holds the work when you lean into it with a breaker bar or a long wrench, which is everyday farm shop reality.
Do I need pipe jaws on a bench vise?
If you cut or thread pipe, yes. The Forward CR50A lists built-in pipe jaws for 1/2 in to 3 1/2 in pipe, the VEVOR covers 0.6 in to 2.8 in, and both Wiltons list built-in pipe jaws. Flat jaws alone will mar or slip on round stock.
What does a swivel base do?
It rotates the vise so you can position the workpiece at the working angle without unbolting anything. Four of these list a 360-degree swivel base with lockdowns; the Forward CR50A lists 210 degrees.
Which vises state a lifetime warranty?
The Wilton WS5 and the Wilton 675U both state a lifetime warranty term. The Forward and VEVOR listings state no warranty term.
More welding guides
– [Bench Vise vs Welding Vise](/bench-vise-vs-welding-vise/)
– [Best Bench Vise for Metal Work](/best-bench-vise-for-metal-work/)





