Bench Vise Size: Jaw Width, Opening and Throat
Bench vise size is jaw width, opening and throat depth, shown here on a 6-1/2-inch Wilton mechanics vise and a 4-inch Wilton apprentice vise.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Wilton Mechanics Pro 6-1/2" Bench & Pipe Vise9.8/10View on Amazon - 2
Wilton 4" Apprentice Bench Vise, Pipe Jaws9.7/10View on Amazon
A vise that is too small for the work can let the work shift, and a vise that is too big takes bench space, so bench vise size is the question to settle before the vise is bolted down. Bench vise size means jaw width, jaw opening and throat depth, and those measurements decide what stock fits and how deep the vise reaches. This guide explains each measurement and shows it on the vises in this guide.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Wilton Mechanics Pro 6-1/2" Bench & Pipe Vise
A 6-1/2-inch mechanics bench and pipe vise with a 6-inch opening, a 4-3/8-inch throat and a 360-degree swivel base.
Pros
- 6-1/2 in jaw width with a 6 in opening and a 4-3/8 in throat depth
- Replaceable pipe jaws hold pipe from 1/4 in to 4 in in diameter
- 60,000 PSI ductile iron with an enclosed spindle and needle roller thrust bearing
- 360-degree swivel base with two hand-tightened lockdowns and a large anvil
Cons
- Weighs 55.6 lb, heavier than the 14.3 lb apprentice vise
- No clamping force is stated, while the apprentice vise states 6,000 lb of force
- Maker states do not use it as a press
- Stated dimensions of 11.0 x 9.4 x 19.3 in need bench space

Wilton 4" Apprentice Bench Vise, Pipe Jaws
A 4-inch apprentice bench vise with a 4-inch opening, a 2-5/8-inch throat and up to 6,000 lb of clamping force.
Pros
- 4 in jaw with a 4 in opening and a 2-5/8 in throat depth
- Clamps with up to 6,000 lb of force across 4 in jaws
- 72,000 PSI ductile iron with rubber pinch-point safety guards
- 360-degree swivel base with dual lockdowns and a large anvil
Cons
- Maker describes it as sized for light-duty bench work, and points to a larger vise for heavy fabrication
- Pipe jaws hold 1/8 to 2 in pipe, a smaller range than the 6-1/2 in vise
- Mounting hardware is not included, while a mounting template is provided
- Anvil is listed for light hammering and forming
Bench vise size in one paragraph
Bench vise size is jaw width, jaw opening and throat depth. The Wilton 865M mechanics vise (on Amazon) states a 6-1/2 in jaw width, a 6 in opening and a 4-3/8 in throat depth, while the Wilton WVA4 apprentice vise (on Amazon) states a 4 in jaw width, a 4 in opening and a 2-5/8 in throat depth. Pipe jaws add another measurement: the 865M holds pipe from 1/4 in to 4 in in diameter, and the WVA4 holds pipe from 1/8 in to 2 in. The 865M weighs 55.6 lb and the WVA4 weighs 14.3 lb, and clamping force is stated only on the smaller vise, at 6,000 lb.
Side by side
| Vise | Gear Score | Jaw width | Opening | Throat | Pipe jaws | Weight |
|---|---|---|---|---|---|---|
| Wilton 865M Mechanics Pro | 9.8/10 | 6-1/2 in | 6 in | 4-3/8 in | 1/4 to 4 in | 55.6 lb |
| Wilton WVA4 Apprentice | 9.7/10 | 4 in | 4 in | 2-5/8 in | 1/8 to 2 in | 14.3 lb |
The table lines up the two vises by measurement. Clamping force is stated only on the apprentice vise. See the bench vise parts guide for what each part of the vise does.
Jaw width, opening and throat
Jaw width is the width across the jaws: the 865M states a 6-1/2 in jaw width, and the WVA4 states a 4 in jaw width. Opening is how far the jaws move apart: the 865M states a 6 in opening, and the WVA4 states a 4 in opening. Throat depth is how deep the vise reaches, and the 865M states a 4-3/8 in throat depth that reaches deeper into brackets and fabricated parts, while the WVA4 states a 2-5/8 in throat depth. Pipe jaws hold round stock, and the 865M holds pipe from 1/4 in to 4 in in diameter, while the WVA4 holds pipe from 1/8 in to 2 in.
What else sizes a vise
Both vises state a 360-degree swivel base. The 865M base locks with two hand-tightened lockdowns and mounts with four 7/16-inch bolts on an 8-3/4-inch bolt circle. The WVA4 base locks on both sides with dual lockdowns and mounts with four bolts, with hardware not included and a mounting template provided. The 865M movable jaw and base are cast from 60,000 PSI ductile iron, with an enclosed spindle and a needle roller thrust bearing, and the WVA4 body is rated at 72,000 PSI ductile iron with rubber pinch-point safety guards. Both vises state a large anvil, and both are backed by the Wilton lifetime warranty.
Do not use the 865M as a press. The maker of the 865M states do not use it as a press, and never put a hammer, pipe extension or cheater bar on the handle. The handle is engineered to bend under excessive force to protect the vise.
The vises in this guide
Jaw width, opening and throat set the size, and the vises below show those measurements on a larger mechanics vise and a smaller apprentice vise.
FAQ for welders
What does bench vise size mean?
Bench vise size means jaw width, jaw opening and throat depth. The vises here state jaws of 6-1/2 in and 4 in, openings of 6 in and 4 in, and throats of 4-3/8 in and 2-5/8 in.
What size bench vise fits light-duty bench work?
The Wilton WVA4 is sized for light-duty bench work, with a 4 in jaw, a 4 in opening and a 2-5/8 in throat. The maker says for heavy fabrication or large stock, step up to the 6 in Apprentice or a larger Wilton vise.
How much do these vises weigh?
The Wilton 865M weighs 55.6 lb, and the Wilton WVA4 weighs 14.3 lb.
Do these vises hold pipe?
Both vises state pipe jaws. The 865M holds pipe from 1/4 in to 4 in in diameter, and the WVA4 holds pipe from 1/8 in to 2 in.
Do both vises swivel?
Both vises state a 360-degree swivel base. The 865M locks with two hand-tightened lockdowns, and the WVA4 locks on both sides with dual lockdowns.
Related: bench vise types, bench vise vs post vise, ductile iron vs cast iron bench vise, and the metal fab tools hub.




