Best Sheet Metal Brake for Gutters (2026)
3 manual sheet metal brakes for gutters compared by width, capacity, bending angle and weight.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallKASTFORCE KF50029.7/10View on Amazon - 2
Best PortableKAKA W-18189.6/10View on Amazon - 3
Best 3-in-1VEVOR 3-in-19.6/10View on Amazon
A gutter run starts as a flat sheet, and the brake turns it into a channel with straight, even bends. The wrong brake leaves wavy edges and bends that drift off the line; the right one holds the sheet flat and the angle steady. This guide compares the best sheet metal brake for gutters: three manual brakes by width, capacity, bending angle and weight, using only what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall KASTFORCE KF5002: 28 inch width, 18 Ga steel and 16 Ga aluminum capacity, and a 0 to 135 degree range. Check price on Amazon
- Best Portable KAKA W-1818: 18 inch brake at 10 lb with pre-drilled mounting holes, though a C-clamp is required. Check price on Amazon
- Best 3-in-1 VEVOR 3-in-1: Bends, shears and rolls in one unit, with 5 segmented blades and a 90 degree max angle. Check price on Amazon
The machines
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | KF5002 Sheet Metal Brake Steel Bending Brake Sheet | 9.7/10 | Buy on Amazon |
| 2 | KAKA INDUSTRIAL Sheet Metal Brake | 9.6/10 | Buy on Amazon |
| 3 | VEVOR Sheet Metal Brake, 12-inch | 9.6/10 | Buy on Amazon |

KF5002 Sheet Metal Brake Steel Bending Brake Sheet
A manual steel bending brake, 28 inches wide, that handles 1.2 mm (18 Ga) mild steel and 1.5 mm (16 Ga) aluminum, with a bending angle from 0 to 135 degrees.
Pros
- 28 inch width, the widest bending width here
- Handles 1.2 mm (18 Ga) mild steel and 1.5 mm (16 Ga) aluminum
- Bending angle from 0 to 135 degrees, the widest range here
- Heavy-duty steel frame for shop and DIY work
Cons
- No warranty term is stated
- 44 lb, heavier than the 10 lb KAKA brake
- No clamping method is named in the listing
- No shear or roll function is stated

KAKA INDUSTRIAL Sheet Metal Brake
An 18 inch portable bending brake with an 18 Ga mild steel capacity and a 0 to 90 degree bending angle, at 10 lb with pre-drilled mounting holes.
Pros
- 10 lb, which weighs less than the other two brakes
- Simple construction, easy to move and work with
- Pre-drilled mounting holes make bending easy
- 18 Ga mild steel capacity matches the KASTFORCE on steel
Cons
- No clamping system is included; a C-clamp is required
- No warranty term is stated
- 0 to 90 degree angle range is narrower than the KASTFORCE range
- No aluminum capacity is stated in the listing

VEVOR Sheet Metal Brake, 12-inch
A 12 inch 3-in-1 combination machine that bends, shears and rolls sheet metal up to 20 Ga (1 mm) thick, with a 90 degree max bending angle and 5 segmented blades.
Pros
- Three functions in one unit: bending, shearing and rolling
- 5 segmented blades in 1, 2 x 2, 3, and 4 inch sizes
- HT200 casting with a T10 shearing blade
- Processes low-carbon steel, aluminum, brass, copper, lead, plastic and zinc
Cons
- No warranty term is stated
- 12 inch width is the narrowest here
- 20 Ga capacity is the thinnest here
- 90 lb, the heaviest unit here
Other welders and gear to compare
VEVOR Box and Pan BrakeCheck price on Amazon
Baileigh 48-Inch Magnetic Sheet Metal BrakeCheck price on Amazon
DURATECH 90 Degree Tubing BenderCheck price on Amazon
KAKA INDUSTRIAL Metal BrakeCheck price on Amazon
KF5017 Press Brake Attachment for 12-20 Ton Hydraulic PressesCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Width | Capacity | Bending angle | Weight |
|---|---|---|---|---|---|
| KASTFORCE KF5002 | 9.7/10 | 28 in | 18 Ga steel, 16 Ga aluminum | 0 to 135 degrees | 44 lb |
| KAKA W-1818 | 9.6/10 | 18 in | 18 Ga mild steel | 0 to 90 degrees | 10 lb |
| VEVOR 3-in-1 | 9.6/10 | 12 in | 20 Ga | 90 degrees max | 90 lb |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 20 October 2026. None of the listings states a warranty term with a length, and none names a safety standard, so all 3 score zero for safety and all 3 score zero for warranty.
How the brakes were scored
Each brake is scored on performance, build, value, safety and warranty, using only what the listing publishes. The How We Pick page explains the weights.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| KASTFORCE KF5002 | 9.7 | 32 | 22 | 21 | n/a | 0 |
| KAKA W-1818 | 9.6 | 29 | 20 | 20 | n/a | 0 |
| VEVOR 3-in-1 | 9.6 | 28 | 21 | 19 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.
What the listings tell you
All 3 listings state a bending width, a thickness capacity and a bending angle. The KASTFORCE states the widest width at 28 inches and the widest angle range at 0 to 135 degrees, plus a separate aluminum capacity. The KAKA states the lowest weight at 10 lb and names its missing clamping system plainly. The VEVOR states the narrowest width at 12 inches and the thinnest capacity at 20 Ga, and it is the only one of the 3 that shears and rolls as well as bends.
Buying guide: choosing the best sheet metal brake for gutters
Width and capacity
Width decides how long a piece the brake can bend in one pass. The KASTFORCE takes material up to 28 inches wide, the KAKA takes 18 inches, and the VEVOR takes 12 inches. Capacity decides how thick the sheet can be: the KASTFORCE handles 1.2 mm (18 Ga) mild steel and 1.5 mm (16 Ga) aluminum, the KAKA handles 18 Ga mild steel, and the VEVOR handles 20 Ga (1 mm) sheet. Match both figures to the gutter stock before ordering, since a brake that is too narrow or too light in capacity cannot take the sheet.
Bending angle
The KASTFORCE bends from 0 to 135 degrees, the widest range here. The KAKA bends from 0 to 90 degrees, and the VEVOR bends to a 90 degree max angle. A wider range covers more bend shapes, while a 90 degree max suits right-angle bends. Check the angle range against the bends the job calls for, since the range is fixed by the brake.
Clamping and holding
A brake needs to hold the sheet still while it bends. The KAKA listing states plainly that there is no clamping system to hold metal in place, so a C-clamp is required. The KASTFORCE and VEVOR listings name no clamping system either, so check how the sheet is held before the first bend. Pre-drilled mounting holes, as on the KAKA, let the brake be fixed to the bench, which keeps the work steady while the sheet moves.
Weight and moving it
Weight decides whether the brake moves between jobs or stays on one bench. The KAKA weighs 10 lb and is built to move, the KASTFORCE weighs 44 lb, and the VEVOR weighs 90 lb. A light brake suits work that moves around the shop; a heavy brake stays put once it is set down. Check the bench before ordering, since the VEVOR needs a bench that holds 90 lb.
Shear and roll extras
Only the VEVOR shears and rolls as well as bends: one unit holds a bending machine, a shearing machine and a rolling machine. The shearing blade is T10 material, and the bending blade and roller are 45# material. The 5 segmented blades come in 1, 2 x 2, 3, and 4 inch sizes for different jobs, and the blade clearance is less than 0.0027 in. The KASTFORCE and KAKA listings state bending only, so a separate shear is needed for cutting with those two.
Before You Strike an Arc
- Check the bending width against the gutter stock: the brakes here take 28, 18 and 12 inches.
- Have a C-clamp ready for the KAKA brake, since its listing states no clamping system is included.
- Check the 5 segmented blades on the VEVOR against the job: 1, 2 x 2, 3, and 4 inch sizes.
- Read the user manual included with the VEVOR before the first bend.
- All 3 brakes are manual, so no power supply is needed; set the brake on a flat, steady bench.
FAQ for welders
What width sheet metal brake fits gutter work?
Match the brake width to the gutter stock. The KASTFORCE takes material up to 28 inches wide, the KAKA takes 18 inches, and the VEVOR takes 12 inches. A wider brake bends longer pieces in one pass, so measure the stock before ordering.
What thickness can these brakes bend?
The KASTFORCE handles 1.2 mm (18 Ga) mild steel and 1.5 mm (16 Ga) aluminum. The KAKA handles 18 Ga mild steel. The VEVOR handles 20 Ga (1 mm) sheet, including low-carbon steel, aluminum, brass, copper, lead, plastic and zinc.
Do any of these brakes shear and roll too?
Only the VEVOR does: it is a 3-in-1 combination machine with bending, shearing and rolling functions. Its shearing blade is T10 material, and its bending blade and roller are 45# material. The KASTFORCE and KAKA listings state bending only.
Does the KAKA brake hold the sheet by itself?
No. The KAKA listing states there is no clamping system to hold metal in place for the brake, so a C-clamp is required. The KAKA does have pre-drilled mounting holes, which make the bending process easy.
What angle can these brakes bend?
The KASTFORCE bends from 0 to 135 degrees. The KAKA bends from 0 to 90 degrees. The VEVOR bends to a 90 degree max angle. Check the angle range against the bends the job calls for.
More welding guides
See the metal fab tools hub, the best hand seamer for gutters, the press brake vs sheet metal brake guide, the sheet metal brake vs hand seamer guide, the best sheet metal gauge thickness tool and the best tin snips for sheet metal.




