Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Right Hand Turning Tool (2026): 4 Picks Compared

Four right-hand turning holders compared on shank size, holder count, inserts and material, from what each listing states.

Best Right Hand Turning Tool (2026): 4 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ASZLBYM 5/8 in SetBest OverallASZLBYM 5/8 in Set9.7/10View on Amazon
  2. 2RupXinSplend SCLCL/SCLCRMost InsertsRupXinSplend SCLCL/SCLCR9.6/10View on Amazon
  3. 3Zouzmin SRACR1212Finishing PickZouzmin SRACR12129.6/10View on Amazon
  4. 4Hunricho SVJCR/L1212Detailed Insert SpecsHunricho SVJCR/L12129.6/10View on Amazon

A shaft needs a shoulder faced and a bore needs a clean pass, and the holder in the tool post decides how that cut goes. This guide compares the best right hand turning tool picks for a home lathe: four holders and sets, scored on what each listing states about shank size, holder count, inserts and material.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall ASZLBYM 5/8 in Set: Three right-hand holders at 5/8 inch shank, 3 inserts, 3 shims and 3 wrench sets, the only all-right-hand set here. Check price on Amazon
  • Most Inserts RupXinSplend SCLCL/SCLCR: Two holders, left and right hand, with 12 CCMT09T304 inserts and 2 wrenches, in 42CrMo steel. Check price on Amazon
  • Finishing Pick Zouzmin SRACR1212: A 90 degree holder with 10 round R3 carbide inserts for finishing and semi-finishing, packed in a plastic container. Check price on Amazon
  • Detailed Insert Specs Hunricho SVJCR/L1212: 35 degree VCMT inserts with stated blade length, thickness and radius, plus 2 holders and 2 wrenches. Check price on Amazon

The machines

3PCS 5/8" Metal Lathe Excircle Indexable Carbide

3PCS 5/8" Metal Lathe Excircle Indexable Carbide

ASZLBYM9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 3 right-hand holders at 5/8 inch shank with 3 carbide inserts, 3 shims and 3 wrench sets, rated HRC 48.

Pros

  • Three right-hand holders, one for each insert type
  • 5/8 inch shank, the largest shank here
  • Hardness rated HRC 48
  • 3 inserts, 3 shims and 3 wrench sets in the box

Cons

  • 3 inserts only, one per holder, so spares need a separate order
  • 5/8 inch shank needs a tool post that takes it
  • Three different insert types, so each holder takes only its own insert
  • Right hand only, so left-hand cuts need a different holder
RupXinSplend Lathe Turning Tools Threading Holder

RupXinSplend Lathe Turning Tools Threading Holder

RupXinSplend9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two indexable holders, one left hand and one right hand, at 1/2 inch shank with 12 CCMT09T304 inserts and 2 wrenches, in 42CrMo steel.

Pros

  • Two holders, left and right hand, in one set
  • 12 CCMT09T304 inserts and 2 wrenches included
  • 42CrMo steel with 1060 degrees Celsius heat treatment
  • Free exchange offered for dissatisfaction

Cons

  • Only one of the two holders is right hand
  • 1/2 inch shank, smaller than the 5/8 inch set here
  • One insert type across both holders
  • No spare wrench beyond the two included
Hunricho 2pcs 1/2" Indexable Metal Lather Turning

Hunricho 2pcs 1/2" Indexable Metal Lather Turning

Hunricho9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two 1/2 inch holders, one right hand and one left hand, with 10 VCMT110304 inserts, 2 T8 wrenches and a 40CrMnTi substrate.

Pros

  • 35 degree VCMT inserts with stated length, thickness and radius
  • Two holders, right and left hand, with 10 inserts
  • 40CrMnTi substrate with vacuum hardening
  • Stated for stainless steel, steel, cast iron and non-ferrous materials

Cons

  • No warranty term is stated
  • Only one of the two holders is right hand
  • Single-sided inserts, so each insert has one cutting edge in use
  • 1/2 inch shank, smaller than the 5/8 inch set here
Zouzmin 1/2" SRACR1212 H06+10Pc R3 Inserts Lathe

Zouzmin 1/2" SRACR1212 H06+10Pc R3 Inserts Lathe

zouzmin9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single 1/2 inch right-hand holder with 10 round R3 carbide inserts and a T8 wrench, in forged 40Cr steel, packed in a plastic container.

Pros

  • Forged 40Cr holder, strong and durable
  • 90 degree cutting angle with round R3 inserts
  • 10 coated carbide inserts included
  • Plastic container keeps holder and inserts stored safe

Cons

  • No warranty term is stated
  • One holder only
  • 10 inserts of a single round type
  • 1/2 inch shank, smaller than the 5/8 inch set here

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Shank Holders Inserts Cutting direction Material
ASZLBYM 5/8 in Set 9.7/10 5/8 in 3, right hand 3 Right hand Not stated
RupXinSplend SCLCL/SCLCR 9.6/10 1/2 in 2, left and right 12 Left and right 42CrMo steel
Hunricho SVJCR/L1212 9.6/10 1/2 in 2, left and right 10 Left and right 40CrMnTi
Zouzmin SRACR1212 9.6/10 1/2 in 1, right hand 10 Right hand 40Cr, forged

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 20 November 2026.

How the picks were scored

Each tool is scored out of 10 on performance, build, value, safety listing and warranty. Turning holders carry no electrical safety listing, so every tool here scores zero on that criterion; the ranking comes from the other four. No warranty term is stated for any holder here, so every tool also scores zero on warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
ASZLBYM 5/8 in Set 9.7 32 22 21 n/a 0
RupXinSplend SCLCL/SCLCR 9.6 30 21 21 n/a 0
Hunricho SVJCR/L1212 9.6 29 21 20 n/a 0
Zouzmin SRACR1212 9.6 28 20 20 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

Buying guide: how to choose the best right hand turning tool

Shank size

Three holders here use a 1/2 inch shank and one set uses a 5/8 inch shank. Match the shank to the tool post and the holder height, since a shank that does not fit the post cannot be set on center.

Holder count and hand

Only the ASZLBYM set gives three right-hand holders. RupXinSplend and Hunricho each give one right-hand and one left-hand holder, and Zouzmin gives a single right-hand holder. Count the right-hand holders before buying, since a left-hand holder cuts the other way.

Inserts

Insert count runs from 3 in the ASZLBYM set to 12 in the RupXinSplend set, with 10 in the Zouzmin and Hunricho sets. Round R3 inserts suit finishing and semi-finishing, while the CCMT and VCMT inserts state their own shapes and sizes. Check that spare inserts for the holder are easy to find.

Material and hardness

Zouzmin states forged 40Cr, RupXinSplend states 42CrMo steel with heat treatment at 1060 degrees Celsius, and Hunricho states a 40CrMnTi substrate with vacuum hardening. ASZLBYM states hardness rated HRC 48 and a black oxidized surface. Compare the stated material and hardness, not the finish alone.

What comes in the box

Wrenches run from 1 T8 wrench with the Zouzmin holder to 3 sets of wrenches with the ASZLBYM set, with 2 wrenches in each of the other two sets. ASZLBYM also includes 3 shims, and Zouzmin packs the holder and inserts in a plastic container. Check the box contents against the holders already on the shelf.

Use as directed. Lathe work needs eye and face protection, the work clamped tight, guards in place, and no gloves near rotating parts. Keep the chuck key out of the chuck before starting the spindle, and never exceed the stated ratings. See the OSHA machine guarding page.

FAQ for welders

Which hand do these holders cut?

ASZLBYM states cutting direction right hand for all three holders, and Zouzmin states right hand in its holder name. RupXinSplend and Hunricho each include one right-hand holder and one left-hand holder. Check the hand on each holder before ordering, since the sets mix hands.

What shank size fits a lathe tool post?

Three holders here use a 1/2 inch shank and the ASZLBYM set uses a 5/8 inch shank. Measure the tool post and the holder height before ordering, and match the shank to the post.

How many inserts come with these holders?

Zouzmin and Hunricho state 10 inserts and ASZLBYM states 3 inserts. RupXinSplend gives two insert counts, 10 and 12, so check before ordering.

What materials can these holders cut?

Zouzmin states finishing and semi-finishing of steel, stainless and cast iron. Hunricho states stainless steel, steel, cast iron and non-ferrous materials. RupXinSplend states CNC cutting of metal and non-metallic materials that are difficult to machine.

Do these sets include wrenches?

Yes. Zouzmin includes 1 T8 wrench, RupXinSplend includes 2 wrenches, ASZLBYM includes 3 sets of wrenches, and Hunricho includes 2 T8 wrenches.

Related: lathe cutting tools, types of lathe tools, the lathe cut off tool and the lathes and mills hub, plus the /Metalworking Machines/ category page.

More buying guides