Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Lathe Cut Off Tool (2026): 5 Holders and Blades Compared

Five lathe cut off tool holders, from 8 mm mini lathe holders to a 12 mm carbide insert holder, compared on shank size, blade type, cutting depth and what comes in the box.

Best Lathe Cut Off Tool (2026): 5 Holders and Blades Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ASZLBYM MGEHR1212-2Best OverallASZLBYM MGEHR1212-29.6/10View on Amazon
  2. 2OSCARBIDE QA12R-30Deepest Stated CutOSCARBIDE QA12R-309.6/10View on Amazon
  3. 3BLUEFOX BCH-0053Best HSS BladeBLUEFOX BCH-00539.6/10View on Amazon
  4. 4TAURISH MPTH-8MM-6BBest Mini Lathe PickTAURISH MPTH-8MM-6B9.5/10View on Amazon

Parting off a finished piece is the final cut on the lathe, and it is the cut with the least room for error. The bar keeps turning, the part hangs on a thin neck of metal, and a dull or flexing blade can grab, chatter or snap the piece off rough. A good lathe cut off tool holds its edge through that cut and leaves a face that needs little cleanup. This roundup of the best lathe cut off tool picks compares holders and blades on what each listing states: shank size, blade or insert type, cutting depth, fit and what comes in the box.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall ASZLBYM MGEHR1212-2: A 12 mm shank holder in 40Cr steel with 11 MGMN200-G carbide inserts, stated insert size, and a listed range of stainless steel, iron, copper and aluminum pipe. Check price on Amazon
  • Deepest Stated Cut OSCARBIDE QA12R-30: A 3/4 inch shank, 5 inches long, with a stated 1.18 inch maximum cutting depth, a GTN-3 carbide insert and a nickel plated finish. Check price on Amazon
  • Best HSS Blade BLUEFOX BCH-0053: An M2 HSS blade, 1/8 x 3/4 x 6 inches, hardened and precisely ground, on a 12 mm shank that fits front or rear tool posts. Check price on Amazon
  • Best Mini Lathe Pick TAURISH MPTH-8MM-6B: An 8 mm shank with 6 M2 HSS blades, each 1.45 x 5 x 63 mm, and an Allen key for installation and adjustment. Check price on Amazon

The machines

ASZLBYM Lathe Grooving Tool Holder Grooving

ASZLBYM Lathe Grooving Tool Holder Grooving

ASZLBYM9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12 mm shank holder in 40Cr steel with 11 carbide grooving inserts, listed for wide and deep grooves in stainless steel, iron, copper and aluminum pipe.

Pros

  • 11 MGMN200-G carbide inserts included, so spares are on hand
  • Holder is 40Cr steel, listed with good anti-rust performance
  • Insert size is fully stated: 1.6 mm thick, 16 mm long, 3.5 mm high
  • Listed for stainless steel, iron, copper and aluminum pipe, plate and non-metallic pipe

Cons

  • 12 mm shank fits only tool posts that take that size
  • The 1.6 mm insert makes a narrow groove, so wide grooves take repeated cuts
  • No warranty term is stated
  • One fixed holder size, with no smaller shank for mini lathes
3/4"x3/4" OSCARBIDE Lathe Grooving & Parting

3/4"x3/4" OSCARBIDE Lathe Grooving & Parting

OSCARBIDE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/4 inch square shank holder, 5 inches long, with a GTN-3 carbide insert and a stated 1.18 inch maximum cutting depth.

Pros

  • States a 1.18 inch maximum cutting depth, the only depth stated here
  • GTN-3 insert stop design holds center height and depth of cut
  • Nickel plated finish and one-piece shank for a rigid setup
  • Wedge clamping holds the insert steady in close face grooving cuts

Cons

  • Only 1 insert is included
  • 3/4 inch shank fits only posts that take that size
  • Right-hand cut only, so left-hand setups need another holder
  • A 5 inch holder with a 1.18 inch cutting depth suits shallow parting; deeper cuts need another tool
Lathe Clamp Type Parting Cut Off Tool Holder 12mm

Lathe Clamp Type Parting Cut Off Tool Holder 12mm

BLUEFOX TOOLS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A clamp type parting holder with a 12 mm shank and a 1/8 x 3/4 x 6 inch M2 HSS blade, made to fit front or rear tool posts.

Pros

  • M2 HSS blade, 1/8 x 3/4 x 6 inches, hardened and precisely ground
  • Fits front or rear tool posts
  • Rigid clamping for heavy duty cuts, per the listing
  • Epoxy black finish for a long rust free life

Cons

  • Only 1 blade is included
  • 12 mm shank fits only posts that take that size
  • A 1/8 inch blade is narrow for wide parting cuts
  • Made for parting bar stock ends and bolt heads; wide grooving is outside its stated use
Mini Parting Tool Cut Off Holder 8mm with 6 Pieces

Mini Parting Tool Cut Off Holder 8mm with 6 Pieces

TAURISH9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A mini lathe parting holder with an 8 mm square shank, 6 M2 HSS blades and an Allen key for installation and adjustment.

Pros

  • 6 M2 HSS blades included, each 1.45 x 5 x 63 mm
  • Allen key included for installation and adjustment
  • 8 mm square shank suits mini lathes and compact setups
  • Shank measures 8 x 8 x 80 mm, stated in full

Cons

  • 8 mm shank suits mini lathes and compact setups only
  • Blades are 5 mm wide, so wide grooves take repeated cuts
  • Made for small metalwork, so heavy cuts on large bar stock are outside its stated use
  • No storage case is listed in the box
Mini Parting Tool Cut off Holder with 6Pcs HSS

Mini Parting Tool Cut off Holder with 6Pcs HSS

LEGLO9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A mini parting tool holder with an 8 mm shank and 6 HSS blades for mini lathes.

Pros

  • 6 HSS blades included with the holder
  • 8 mm shank suits mini lathes
  • Made for rigid clamping on mini lathes
  • Simple kit: holder plus blades, ready for small lathe work

Cons

  • 8 mm shank suits mini lathes only
  • No warranty term is stated
  • No Allen key is listed in the box
  • No storage case is listed in the box

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Shank Blade or insert Cutting depth Inserts in box Fit Warranty
ASZLBYM MGEHR1212-2 9.6/10 12 mm MGMN200-G carbide, 1.6 mm thick Not stated 11 inserts Wide and deep grooves None stated
OSCARBIDE QA12R-30 9.6/10 3/4 x 3/4 in GTN-3 carbide 1.18 in 1 insert External parting and grooving None stated
BLUEFOX BCH-0053 9.6/10 12 mm M2 HSS, 1/8 x 3/4 x 6 in Not stated 1 blade Front or rear tool posts None stated
TAURISH MPTH-8MM-6B 9.5/10 8 x 8 mm M2 HSS, 1.45 x 5 x 63 mm Not stated 6 blades Mini lathes None stated
LEGLO AAA-240 9.4/10 8 mm HSS Not stated 6 blades Mini lathes None stated

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 19 November 2026.

How to choose the best lathe cut off tool

Shank size and fit

Two holders here use a 12 mm shank, one uses a 3/4 inch square shank, and the two mini lathe holders use an 8 mm shank. Match the shank to the tool post on the lathe before ordering, since a holder that does not fit the post cannot be clamped rigid. The BLUEFOX holder fits front or rear tool posts, which helps when the parting setup sits behind the work.

Carbide inserts or HSS blades

Two picks here cut with carbide inserts and three cut with HSS blades. The ASZLBYM holder comes with 11 MGMN200-G carbide inserts, and the OSCARBIDE holder comes with a single GTN-3 carbide insert. The BLUEFOX and TAURISH blades are M2 HSS, and the LEGLO blades are HSS. A box with more inserts or blades means fewer reorders once the first edge wears out.

Cutting depth

Only one listing here states a maximum cutting depth: the OSCARBIDE, at 1.18 inches. The ASZLBYM is listed for wide and deep groove machining, but no depth figure is given. When the depth is not stated, check the insert or blade length against the work before ordering.

What comes in the box

The ASZLBYM kit holds a holder and 11 inserts in a plastic container. The TAURISH kit holds a holder, 6 M2 HSS blades and an Allen key for installation and adjustment. The LEGLO kit holds a holder and 6 HSS blades, the OSCARBIDE kit holds a holder and a single GTN-3 insert, and the BLUEFOX kit holds a holder and a single HSS blade. Count the spares before ordering, since a parting blade is a consumable that gets replaced.

Mini lathe fit

Mini lathes take smaller holders, and both mini picks here use an 8 mm shank. The TAURISH shank measures 8 x 8 x 80 mm, and its blades measure 1.45 x 5 x 63 mm. The LEGLO holder is also listed for mini lathes with an 8 mm shank. A full size holder does not belong on a mini lathe post, so check the shank size against the post before ordering.

Use as directed. Wear eye and face protection, clamp the work firmly, keep guards in place, and keep gloves away from rotating parts. Set the tool at center height and lock the holder before starting the lathe. See the OSHA machine guarding page and the Safety Disclaimer.

Before You Strike an Arc

  • Set the tool tip at center height before the first cut; the OSCARBIDE insert stop is made to hold that height.
  • Clamp the holder tight in the tool post and check the shank size matches the post.
  • Keep guards in place and wear eye and face protection; keep gloves away from rotating parts.
  • Check what arrived against the listing: holder, blades or inserts, and the Allen key where the listing includes one.
  • Confirm the blade or insert is seated and clamped before starting the lathe.

FAQ for welders

How to set up a knurling tool on a lathe?

A knurling tool mounts in the tool post like other lathe tools, with the knurl wheels set square to the work and the tool tip at center height. The picks here are parting and grooving tools, not knurling tools, so none of them lists knurl wheels. Set the tool height first, then feed the knurls into the work and keep the work clamped firmly.

How to set lathe tool height?

Set the tool tip at center height, so the cutting edge meets the center line of the work. The OSCARBIDE holder has a GTN-3 insert stop design that the maker says assures accuracy of center height. A tool set too high rubs and a tool set too low drags, so check the height before the first cut.

How to set up metal lathe tools?

Fit the shank in the tool post, clamp it rigid, and set the tip at center height. The TAURISH kit includes an Allen key for installation and adjustment, and the OSCARBIDE holder uses a one-piece shank that adapts to any machine type and turret configuration, per its listing. Check the shank size against the post: 12 mm, 3/4 inch or 8 mm here.

How to set up a metal lathe cutting tool?

Start with the shank size and the tool post: the holders here use 12 mm, 3/4 inch and 8 mm shanks. Seat the blade or insert, clamp the holder, and set the tip at center height before cutting. The BLUEFOX holder fits front or rear tool posts, which gives two mounting options for the same cut.

How to set tools on CNC lathe?

Check the turret or tool post fit first, since these holders are sized by shank: 12 mm, 3/4 inch and 8 mm here. The OSCARBIDE listing says its integral shank holder adapts to any machine type and turret configuration. Set the tool offset to center height and lock the holder before running the program.

Related: metalworking machines, lathes and mills, types of lathe tools, metal lathe for beginners, best CNC lathe tools, parts of a lathe chuck, CNC lathe setup and mini lathe vs mini mill.

Scoring, line by line

Each tool is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Lathe cut off tools have no electrical safety listing to state, so every tool here scores zero on that criterion, and no listing here states a warranty term, so warranty is zero for all five. The ranking comes from performance, build and value.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
ASZLBYM MGEHR1212-2 9.6 30 21 21 n/a 0
OSCARBIDE QA12R-30 9.6 29 21 20 n/a 0
BLUEFOX BCH-0053 9.6 28 20 20 n/a 0
TAURISH MPTH-8MM-6B 9.5 27 19 20 n/a 0
LEGLO AAA-240 9.4 24 18 19 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.

More buying guides