Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Jigsaw Blade for Sheet Metal (2026): 5 Picks Compared

Five T-shank jigsaw blades and sets for sheet metal compared by TPI, gauge range, material, length and pack size.

Best Jigsaw Blade for Sheet Metal (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Bosch T118G BladesBest Jigsaw Blade OverallBosch T118G Blades9.7/10View on Amazon
  2. 2Bosch T321AF3 BladesBest for Thicker SheetBosch T321AF3 Blades9.6/10View on Amazon
  3. 3MRCGTCE 50-Piece SetBest Big Blade SetMRCGTCE 50-Piece Set9.6/10View on Amazon
  4. 4YOSIGHT 20-Piece SetBest Mid-Size SetYOSIGHT 20-Piece Set9.6/10View on Amazon
  5. 5Romeda 10-Piece SetBest Small SetRomeda 10-Piece Set9.5/10View on Amazon

A patch panel needs trimming, the sheet is already cut to rough size, and the grinder would take off too much at the edge. A jigsaw with the right blade follows the line without chewing the metal, which is exactly what the best jigsaw blade for sheet metal is for. This guide compares five T-shank blades and sets on tooth count, gauge range, material, length and pack size.

Every figure below comes from the manufacturer’s listing; where a listing is thin on specs, the copy says so. The two Bosch listings are the only ones that name a gauge range, so they anchor the comparison.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Jigsaw Blade Overall Bosch T118G Blades: 36 TPI for sheet metal 17-26 gauge, HSS, 3-5/8 in, 5 blades. Check price on Amazon
  • Best for Thicker Sheet Bosch T321AF3 Blades: 21 TPI bimetal for 10-16 gauge, 5-1/4 in, pipes and profiles. Check price on Amazon
  • Best Big Blade Set MRCGTCE 50-Piece Set: 50 T-shank blades, assorted types, storage case included. Check price on Amazon
  • Best Mid-Size Set YOSIGHT 20-Piece Set: 20 blades in 9 types with clear markings and a storage box. Check price on Amazon
  • Best Small Set Romeda 10-Piece Set: 10 assorted T-shank blades, SK5 steel, T118A and T118B for metal. Check price on Amazon

The machines

BOSCH T118G 5-Piece 3-5/8 In. 36 TPI Basic

BOSCH T118G 5-Piece 3-5/8 In. 36 TPI Basic

Bosch9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece set of 3-5/8 in, 36 TPI high-speed steel T-shank blades made for sheet metal 17-26 gauge and very thin metals 1/64 to 3/64 in.

Pros

  • 36 TPI for sheet metal 17-26 gauge
  • High-speed steel for maximum life in straight cuts
  • Made for 1/64 to 3/64 in ferrous and non-ferrous metals
  • Fits Bosch and other T-shank jigsaws

Cons

  • No warranty term stated on the listing
  • 5 blades, the second-smallest pack here
  • Straight cuts only, per the listing
  • 1.12 ounces per blade, light for heavy stock
Bosch T321AF3 3 pc. 5-1/4 In. 21 TPI Speed

Bosch T321AF3 3 pc. 5-1/4 In. 21 TPI Speed

Bosch9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece set of 5-1/4 in, 21 TPI bimetal T-shank blades for sheet metal 10 to 16 gauge, pipes, profiles and tube stock.

Pros

  • 21 TPI for sheet metal 10 to 16 gauge
  • Bimetal construction for durability and long life
  • Extra-long 5-1/4 in, 4-1/4 in working length
  • Covers pipes, profiles, tube stock and angle iron

Cons

  • No warranty term stated on the listing
  • 3 blades, the smallest pack here
  • Not for very thin 17-26 gauge sheet
  • 22.68 g per blade
50 Piece Contractor Jigsaw Blades Set with Storage

50 Piece Contractor Jigsaw Blades Set with Storage

MRCGTCE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 50-piece assorted T-shank jigsaw blade set in high carbon steel and high speed steel, with a storage case, covering wood, plastic and metal.

Pros

  • 50 blades, the largest set here
  • Assorted types including T118A and T118B
  • High carbon steel and high speed steel
  • Storage case included

Cons

  • No warranty term stated on the listing
  • No TPI stated for any blade
  • No gauge range stated
  • 0.27 kg for the set
20 Pcs Jigsaw Blades Set with Case 9 Types

20 Pcs Jigsaw Blades Set with Case 9 Types

YOSIGHT9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 20-piece assorted T-shank set in 9 types of high carbon steel and bi-metal, with clear markings and a transparent storage box.

Pros

  • 20 blades in 9 types, clearly marked
  • High carbon steel and bi-metal
  • T118AF and T118BF listed for metal
  • Transparent storage box

Cons

  • No warranty term stated on the listing
  • No TPI stated for any blade
  • No gauge range stated
  • No blade length stated
Jigsaw Blades, 10 Piece Jig Saw Blades

Jigsaw Blades, 10 Piece Jig Saw Blades

Romeda9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-piece assorted T-shank set in SK5 high carbon steel with T118A and T118B blades for basic metal, and 24-hour seller support.

Pros

  • SK5 high carbon steel
  • T118A and T118B listed for basic metal
  • 10 blades across wood, metal and plastic
  • Seller promises issue resolution within 24 hours

Cons

  • No warranty term stated on the listing
  • No TPI stated for any blade
  • No gauge range stated
  • 0.06 kg, the lightest set here

Other welders and gear to compare

Spec sheet comparison

Model Pieces TPI Sheet metal range Length Material
Bosch T118G Blades 5 36 17-26 gauge, 1/64 to 3/64 in 3-5/8 in High-speed steel
Bosch T321AF3 Blades 3 21 10-16 gauge, 1/16 to 1/8 in 5-1/4 in Bi-metal
MRCGTCE 50-Piece Set 50 Not stated Not stated Not stated High carbon steel, high-speed steel
YOSIGHT 20-Piece Set 20 Not stated Not stated Not stated High carbon steel, bi-metal
Romeda 10-Piece Set 10 Not stated Not stated Not stated SK5 high carbon steel

All specs here repeat what the maker rates and the listing prints, copied down 22 October 2026. Where a listing states no TPI or gauge range, the table says so.

Buying guide: the best jigsaw blade for sheet metal

TPI and tooth count

Tooth count is the number that matters most here. The Bosch T118G lists 36 TPI for sheet metal 17-26 gauge and very thin metals 1/64 in to 3/64 in thick, ferrous and non-ferrous. The Bosch T321AF3 lists 21 TPI for sheet metal 10 to 16 gauge and thin metals 1/16 in to 1/8 in thick. More teeth per inch means a finer cut in thinner stock; the assorted sets list blade type codes like T118A and T118B but state no TPI, so you are buying the code, not a stated tooth count.

Gauge range

Only the two Bosch listings name the metal they are made for. The T118G covers 17-26 gauge sheet metal and 1/64 in to 3/64 in thick stock. The T321AF3 covers 10 to 16 gauge sheet metal, 1/16 in to 1/8 in thick stock, pipes less than 2-1/2 in in diameter, tube stock and angle iron. The assorted sets list metal among their materials but name no gauge, so match them to light work or check the blade code against the maker’s chart.

Material: HSS, bimetal or carbon steel

The T118G is high-speed steel, which the listing says gives maximum life in straight cuts. The T321AF3 is bimetal, listed for durability and long life. The MRCGTCE set mixes high carbon steel and high speed steel. The Romeda set is SK5 high carbon steel. The YOSIGHT set mixes high carbon steel and bi-metal. For sheet metal, HSS and bimetal are the listings’ own recommendations; carbon steel sets trade longevity for piece count.

Length

The T118G is 3-5/8 in overall with a 2-5/8 in working length. The T321AF3 is extra-long at 5-1/4 in overall with a 4-1/4 in working length, which suits pipes and profiles as well as sheet. The assorted sets state no blade length, so check the pack if your saw needs a minimum.

Tooth design

Beyond TPI, the Bosch listings name their tooth geometry. The T118G has a wavy set and milled teeth, which the listing pairs with its 36 TPI for smooth cuts in very thin materials. The T321AF3 lists a 21 TPI tooth design for smooth, very fast cuts. The assorted sets name no tooth geometry, so their cut quality is whatever the type code delivers. For visible edges on thin sheet, the stated tooth design is worth weighing alongside the TPI.

Shank and compatibility

All five listings are T-shank. The Bosch T118G listing says it works in Bosch and other T-shank and combination T-U shank jigsaws. The MRCGTCE listing states compatibility with jigsaw power tools with T-shank blade compatibility. The Romeda listing claims compatibility with over 90% of power curve saws. The YOSIGHT and Bosch T321AF3 listings name T-shank without a compatibility claim. If your saw is an older U-shank model, the combination shank note on the T118G is the one to check.

Weight and handling

Blade weight barely matters on the saw, but the set weight tells you about the case. The MRCGTCE 50-piece set weighs 0.27 kg with its storage case, the YOSIGHT 20-piece ships in a transparent storage box, and the Romeda 10-piece weighs 0.06 kg. Per blade, the Bosch T118G is 1.12 ounces and the T321AF3 is 22.68 g. A heavier case stays put on the bench; a light set travels in the tool bag.

Seller support

The Romeda listing promises issue resolution within 24 hours, the only support promise here. The other four listings state no support terms and no warranty terms. A support promise is not a warranty, but for an assorted set bought on type codes, knowing the seller answers within a day is worth something.

Assorted sets vs dedicated blades

The dedicated Bosch blades name their TPI, gauge range and length; the assorted sets trade that detail for piece count: 50 in the MRCGTCE set, 20 in the YOSIGHT set and 10 in the Romeda set, with storage cases or boxes. If you cut sheet metal often, the dedicated blades’ stated specs are worth more than a drawer of mixed codes. If you cut a little of everything, the assorted sets cover wood, plastic and metal in one purchase.

Cut safe. Wear eye protection and secure the workpiece before the blade moves. Unplug the saw before changing blades, and use the proper lubricant when cutting metal, as both Bosch listings recommend. Let the blade do the work; forcing it overheats the teeth and the metal.

FAQ for welders

What TPI should I use for sheet metal?

The listings here give two answers: 36 TPI on the Bosch T118G for 17-26 gauge sheet, and 21 TPI on the Bosch T321AF3 for 10 to 16 gauge sheet. Thinner stock wants more teeth per inch.

Can these blades cut pipe as well as sheet?

The Bosch T321AF3 listing covers pipes less than 2-1/2 in in diameter, tube stock and angle iron alongside sheet metal 10 to 16 gauge. The T118G listing is for sheet metal and very thin metals only.

Do I need cutting lubricant?

Both Bosch listings recommend proper lubricant when cutting metal. The assorted sets do not mention lubricant, but the advice applies to any metal cut.

Will these fit my jigsaw?

All five are T-shank blades. The MRCGTCE listing states T-shank blade compatibility, the Romeda listing claims compatibility with over 90% of power curve saws, and the Bosch blades fit Bosch and other T-shank and combination T-U shank jigsaws.

How many blades do I actually need?

Pack sizes here run from 3 to 50. The dedicated Bosch packs are 5 and 3 blades for one job type; the assorted sets are 10, 20 and 50 blades across wood, plastic and metal. Buy the pack that matches how much metal you cut.

Related: the metal nibbler vs jigsaw comparison, the best hole saw for sheet metal, the best hacksaw for cutting steel, the best cutting fluid for metal and the metal fab tools hub.

Scoring, line by line

Each blade is scored on performance, build, value, safety and warranty, with the Gear Score weights this site publishes. No listing states a safety certification or a concrete warranty term, so safety and warranty are zero across the board.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Bosch T118G Blades 9.7 33 22 19 n/a 0
Bosch T321AF3 Blades 9.6 32 22 18 n/a 0
MRCGTCE 50-Piece Set 9.6 28 20 22 n/a 0
YOSIGHT 20-Piece Set 9.6 28 20 21 n/a 0
Romeda 10-Piece Set 9.5 27 19 21 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides