Best Hand Tubing Cutter (2026): 4 Picks Compared
Four hand tubing cutters for copper, brass, aluminum and PVC compared by cutting range, feed, materials and extras in the box.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallKlein 50067 Micro Cutter9.6/10View on Amazon - 2
Best Close QuartersRIDGID 118 Close Quarters9.6/10View on Amazon - 3
Best Ratcheting SetGDFHBNG Ratcheting Cutter9.6/10View on Amazon - 4
Best for PVCImgjsx Ratcheting Cutter9.5/10View on Amazon
A copper line under a sink leaves no room for a full swing, and the best hand tubing cutter is the one that turns in close quarters and leaves a clean, square edge. We compared four hand cutters on cutting range, materials, feed and what comes in the box, using only what each listing states. Two of them ratchet, one feeds itself, and one keeps it simple with a T-handle, so match the cutter to the tube and the space around it.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Klein 50067 Micro Cutter: 1/8 to 7/8 inch range, T-handle, tool-free blade change, tank key Check price on Amazon
- Best Close Quarters RIDGID 118 Close Quarters: 1/4 to 1-1/8 inch range with AUTOFEED for tight spots Check price on Amazon
- Best Ratcheting Set GDFHBNG Ratcheting Cutter: Ratcheting head, deburring tool, 4 replacement heads, case Check price on Amazon
- Best for PVC Imgjsx Ratcheting Cutter: Cuts copper, PVC and soft metal, 1/4 to 7/8 inch, spare blade Check price on Amazon
The machines

Klein Tools 50067 Micro Tubing Cutter
A compact micro cutter for copper and aluminum tubing from 1/8 to 7/8 inch, with a sliding T-handle and tool-free blade changes.
Pros
- Cuts copper and aluminum tubing from 1/8 to 7/8 inch
- Sliding T-handle gives leverage and control in tight spaces
- Tool-free blade replacement with a simple push-pin mechanism
- Integrated tank key on the bottom for loosening and tightening tanks
Cons
- No warranty term is stated
- Tops out at 7/8 inch, so larger tube needs another cutter
- No replacement blade is stated in the box
- No deburring tool is stated

RIDGID 32573 Model 118 2-in-1 Close Quarters
A 2-in-1 close-quarters cutter with AUTOFEED for copper, brass and aluminum tubing from 1/4 to 1-1/8 inches.
Pros
- Cuts copper, brass and aluminum from 1/4 to 1-1/8 inches
- AUTOFEED advances the blade automatically
- 2-in-1 close-quarters design for tight spaces
- Manufactured in the United States
Cons
- No warranty term is stated
- No deburring tool is stated
- No replacement blade is stated in the box
- No PVC cutting is stated, so plastic tube needs another cutter

Ratcheting Tubing Cutter, Copper Pipe Cutter
A ratcheting cutter with a 360-degree rotating head, a deburring tool, 4 replacement heads and a storage case.
Pros
- Ratcheting action advances the blade with each squeeze
- 360-degree rotating head swivels for tight spaces
- Deburring tool with 4 high speed steel blades included
- 4 replacement cutter heads and a reusable storage case
Cons
- Metal pipe cutting is stated for thin-wall pipe
- Thin, soft plastic tubing will not cut
- Suits copper, brass and aluminum, with no stainless steel stated
- Red color only

Ratcheting Tubing Cutter
A ratcheting cutter for copper, PVC and soft metal pipe from 1/4 to 7/8 inch, with a spare blade in the handle.
Pros
- Cuts copper, PVC and soft metal pipe from 1/4 to 7/8 inch
- Ratcheting action with a longer handle for less effort
- Durable steel blade, replaceable, with a spare in the handle
- 2-in-1 design works alone or with additional ratchet handles
Cons
- No deburring tool is stated
- No replacement heads beyond the one spare blade are stated
- The 1/4 to 7/8 inch range tops out below the 1-1/8 inch cutters here
- Red color only
Spec sheet comparison
| Cutter | Gear Score | Cutting range | Materials | Feed | Extras |
|---|---|---|---|---|---|
| Klein 50067 Micro Cutter | 9.6/10 | 1/8 to 7/8 in | Copper, aluminum | Easy-adjust knob | Tank key |
| RIDGID 118 Close Quarters | 9.6/10 | 1/4 to 1-1/8 in | Copper, brass, aluminum | AUTOFEED | Not stated |
| GDFHBNG Ratcheting Cutter | 9.6/10 | 5/16 to 1-1/8 in | Copper, brass, aluminum, metal | Ratcheting | Deburring tool, 4 heads |
| Imgjsx Ratcheting Cutter | 9.5/10 | 1/4 to 7/8 in | Copper, PVC, soft metal | Ratcheting | Spare blade in handle |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 November 2026.
Buying guide: how to choose the best hand tubing cutter
Cutting range
Ranges here run from 1/8 to 7/8 inch on the Klein micro cutter to 1/4 to 1-1/8 inches on the RIDGID 118. The GDFHBNG cutter gives two ranges, 5/16 to 1 1/8 inches and 1/4 to 7/8 inches, so check before ordering. The Imgjsx cutter covers 1/4 to 7/8 inch, or 6 to 23 mm. Measure the largest tube on the job first, then pick a cutter whose top end clears it.
Wheel cutters and ratcheting cutters
The Klein and RIDGID cutters are wheel type cutters: a knob feeds the wheel as you turn the tool around the tube. The GDFHBNG and Imgjsx cutters ratchet: each squeeze advances the blade, and the longer handle on the Imgjsx needs less effort to rotate. Ratcheting cutters suit conduit near a wall or other piping where a standard cutter cannot fully rotate. Wheel cutters suit open runs where you can swing the tool freely.
Materials
The Klein cutter states copper and aluminum. The RIDGID cutter states copper, brass and aluminum. The GDFHBNG cutter states soft and hard copper, brass, aluminum and thin-wall metal pipe. The Imgjsx cutter states copper, PVC and soft metal pipe. Match the cutter to the tube on the job, and note that thin, soft plastic tubing will not cut on the GDFHBNG cutter.
What comes in the box
The GDFHBNG boxed set includes 4 replacement cutter heads, a deburring tool with a red handle and 4 high speed steel blades, and a reusable storage case. The Imgjsx cutter comes with a spare blade in the handle. The Klein cutter changes blades tool-free with a push-pin mechanism, and the RIDGID cutter lists no spare blade or deburring tool. A deburring tool matters because a cut tube edge needs cleaning before it fits a fitting.
Close quarters work
Three of these cutters are built for tight spaces: the RIDGID 118 is a 2-in-1 close-quarters cutter, the GDFHBNG head rotates 360 degrees, and the Imgjsx cutter is made for conduit near a wall. The Klein micro cutter measures 5.4 x 3.7 x 0.9 inches, with a sliding T-handle for leverage in tight spaces. If the tube sits against a wall, a ratcheting cutter or a close-quarters wheel cutter earns its keep.
Use as directed. Clamp the tube before you cut, keep fingers clear of the wheel and the ratchet, and wear eye protection when you cut and deburr. Deburr the cut edge before fitting, and check the blade for nicks before each cut. See the OSHA welding overview and our Safety Disclaimer.
Before You Strike an Arc
- Check the cutter wheel for nicks and confirm the spare blade sits in the handle on the Imgjsx cutter.
- Match the cutter range to the tube before the first cut.
- Clamp the tube so it cannot roll while you cut.
- Deburr the cut edge with the GDFHBNG deburring tool before fitting.
- Keep the storage case closed so the replacement heads stay together.
FAQ for welders
What is a tubing cutter?
A tubing cutter is a hand tool that scores and cuts tube with a wheel or a ratcheting blade instead of a saw. The cutters here cut copper, aluminum, brass, PVC and thin-wall metal pipe, depending on the model. A wheel cutter turns around the tube while a knob feeds the wheel, and a ratcheting cutter advances the blade with each squeeze.
What size tubing cutter do I need?
Measure the largest tube on the job. The Klein cutter covers 1/8 to 7/8 inch, the RIDGID cutter covers 1/4 to 1-1/8 inches, and the Imgjsx cutter covers 1/4 to 7/8 inch. The GDFHBNG cutter gives two ranges, 5/16 to 1 1/8 inches and 1/4 to 7/8 inches, so check before ordering.
Can a tubing cutter cut PVC?
The Imgjsx cutter states copper, PVC and soft metal pipe. The GDFHBNG cutter cuts rigid PVC tubing, while thin, soft plastic tubing will not cut. The Klein and RIDGID cutters state metal tube only.
Do these cutters come with a deburring tool?
One does: the GDFHBNG boxed set includes a deburring tool with a red handle and 4 high speed steel blades. The other three cutters state no deburring tool. Deburr the cut edge before fitting the tube.
Which tubing cutter is best for tight spaces?
The RIDGID 118 is a 2-in-1 close-quarters cutter with AUTOFEED. The GDFHBNG cutter has a 360-degree rotating head, and the Imgjsx cutter suits conduit near a wall. The Klein micro cutter uses a sliding T-handle for leverage in tight spaces.
Related: sheet metal and tubing hub, tube tools, best tube bender for copper pipe, best copper deburring tool, best tubing notcher. Also see our best cut off wheel for square tubing. Also see our best jigsaw blade for steel tubing. Also see our best tube bender for aluminum tubing.
Scoring, line by line
Each cutter is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Hand tubing cutters carry no electrical safety listing to state, so every cutter here scores zero on that criterion; the ranking comes from the other four. None of the four states a warranty term, so every cutter here also scores zero on warranty.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Klein 50067 Micro Cutter | 9.6 | 30 | 21 | 21 | n/a | 0 |
| RIDGID 118 Close Quarters | 9.6 | 30 | 21 | 20 | n/a | 0 |
| GDFHBNG Ratcheting Cutter | 9.6 | 28 | 20 | 21 | n/a | 0 |
| Imgjsx Ratcheting Cutter | 9.5 | 27 | 19 | 20 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




