Best Bench Vise Under $75 (2026): 5 Picks for the Shop
Best bench vise under $75: five vises compared on jaw width, jaw opening, throat depth, swivel base, material and warranty, from what each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAV Steel 4-1/2 Inch Bench Vise9.6/10View on Amazon - 2
Best Clamping ForceForward 4 Inch Bench Vise9.6/10View on Amazon - 3
Large Jaw PickGOEHNER 6 Inch Bench Vise9.6/10View on Amazon - 4
Small Parts PickFasmov 3 Inch Table Vise9.4/10View on Amazon
A bracket needs a square edge, a pipe needs a steady hold, and a small part needs jaws that do not let go while a drill or a file does its work. When the bench is the whole shop, a vise that holds firm and turns to the angle the job needs saves time and saves scrap. This guide covers the best bench vise under 75, compared on jaw width, jaw opening, throat depth, swivel base, material and warranty, from what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall AV Steel 4-1/2 Inch Bench Vise: 4-1/2 inch jaw, 3-3/4 inch opening, 240 degree base, lifetime warranty. Check price on Amazon
- Best Clamping Force Forward 4 Inch Bench Vise: 4,400 lbs force, ductile iron body, 4 inch jaw and opening, anvil. Check price on Amazon
- Large Jaw Pick GOEHNER 6 Inch Bench Vise: 6 inch jaw, 4.3 inch opening, pipe and flat jaws, 270 degree base. Check price on Amazon
- Small Parts Pick Fasmov 3 Inch Table Vise: 3 inch jaws, 2 inch opening, 1.9 pounds, rubber jaws for small parts. Check price on Amazon
The machines

AV Steel 4-1/2" Bench Vise with 240° Flexible
A 4-1/2 inch cast iron bench vise with a 3-3/4 inch jaw opening, a 240 degree swivel base, pipe jaws, an anvil and a lifetime warranty.
Pros
- Lifetime warranty against design, materials, and workmanship defects
- Pipe jaw range of 5/8 inch to 1-7/8 inch plus a 3-1/4 inch square anvil
- 240 degree swivel base for flexible positioning at the bench
- 2,250 lbs clamping force stated in the listing
Cons
- Throat depth of 2-11/32 inch is shallower than the Forward pick
- No safety certification is stated in the listing
- Jaw width is narrower than the 6 inch picks here

Forward 30404 4 Inch Bench Vise Heavy Duty
A 4 inch heavy duty bench vise with a ductile iron body, 4,400 lbs clamping force, a 360 degree swivel base and a large anvil.
Pros
- 4,400 lbs clamping force stated in the listing
- High-strength ductile iron body rated at 60,000 PSI
- 360 degree swivel base with dual locking nuts
- Replaceable top machinist jaws and built-in pipe jaws
Cons
- No warranty term is stated in the listing
- No safety certification is stated in the listing
- Pipe capacity is limited to 1/2 inch to 1 1/2 inch diameter
- 15.5 pounds, heavier than the AV Steel and Fasmov picks
![[Upgraded] Bench Vise 6" Table Vice](https://m.media-amazon.com/images/I/91ZdQX9i1XL._AC_SL500_.jpg)
[Upgraded] Bench Vise 6" Table Vice
A 6 inch cast iron bench vise with a 4.3 inch jaw opening, pipe and flat jaws, a 270 degree swivel base and double lockdown.
Pros
- 6 inch jaw width, the joint widest here with the sanheshun pick
- Cast iron construction rated at 60,000 PSI
- Pipe and flat jaws for round stock and flat materials
- Double lockdown for precise positioning and added security
Cons
- Title lists 3.3 inch, 4.5 inch and 6 inch jaws while the bullets state a 6 inch jaw
- Listing states 3-year factory services, not a warranty term
- No safety certification is stated in the listing

Bench Vise Heavy Duty 6-Inch
A 6 inch bench vise with a 360 degree double locking swivel base, an oversized striking anvil and cast iron and steel construction.
Pros
- 6 inch jaw width, the joint widest here with the GOEHNER pick
- 360 degree double locking swivel base for various angles
- Oversized striking anvil for knock resistant work
- Forged jaws after heat treatment for strong clamping force
Cons
- No jaw opening is stated in the listing
- No throat depth is stated in the listing
- No warranty term is stated in the listing
- No safety certification is stated in the listing

Fasmov Swivel 3" Universal Table Vise Tilts Rotate
A small 3 inch table vise with cast aluminum construction, rubber jaws, a clip mount and rotation to any angle for small parts work.
Pros
- Lightweight at 1.9 pounds for portable bench work
- Rubber jaws for no scratch and firm clamping
- Rotates to any possible angle with a clip mount
- Jaws of hardened high-carbon steel alloy, 3 inch by 3/4 inch
Cons
- Jaw opening of only 2 inch, the smallest here
- Cast aluminum body, not cast iron or ductile iron
- No anvil is stated in the listing
- No warranty term is stated in the listing
Other welders and gear to compare
Forward 1306 6 Inch Bench Vise Workbench Vise with Anvil andCheck price on Amazon
PONY 4 Inch Heavy Duty Bench ViseCheck price on Amazon
VEVOR Bench ViseCheck price on Amazon
Bench ViseCheck price on Amazon
Forward 1750B 5 Inch Bench Vise Heavy Duty with Anvil andCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Jaw width | Max jaw opening | Throat depth | Material | Swivel base | Warranty |
|---|---|---|---|---|---|---|---|
| AV Steel 4-1/2 Inch Bench Vise | 9.6/10 | 4-1/2 in | 3-3/4 in | 2-11/32 in | Cast Iron | 240° | Lifetime |
| Forward 4 Inch Bench Vise | 9.6/10 | 4 in | 4 in | 2 3/8 in | Ductile Iron | 360° | Not stated |
| GOEHNER 6 Inch Bench Vise | 9.6/10 | 6 in | 4.3 in | 2 in | Cast Iron | 270° | 3-year factory services |
| sanheshun 6 Inch Bench Vise | 9.5/10 | 6 in | Not stated | Not stated | Alloy Steel, Cast Iron | 360° | Not stated |
| Fasmov 3 Inch Table Vise | 9.4/10 | 3 in | 2 in | Not stated | Aluminum | 360° | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (25 October 2026). Where a listing states a figure two ways, the table shows both.
How to choose the best bench vise under 75
Jaw width and opening
Jaw widths among these picks run from 3 inch to 6 inch, and jaw openings run from 2 inch to 4.3 inch. Width sets how much of the work the jaws can grip at once, while opening sets the thickest work the vise can close around. Check both figures against the work on the bench, not just the headline size, since the sanheshun listing states a 6 inch size with no jaw opening at all.
Throat depth and pipe jaws
Throat depth sets how far into the jaws a piece can sit, and the stated depths here run from 2 inch to 2 3/8 inch where the listing gives one. Pipe jaws matter when round stock is part of the job: the Forward listing states pipe capacity of 1/2 inch to 1 1/2 inch diameter, and the AV Steel listing states a pipe jaw range of 5/8 inch to 1-7/8 inch. The GOEHNER listing states pipe and flat jaws without a range, so confirm the fit before buying for pipe work.
Swivel base and mounting
Swivel bases among these picks run from a 240 degree base on the AV Steel vise to 360 degree bases on the Forward, sanheshun and Fasmov vises, with a 270 degree base on the GOEHNER vise. A swivel base lets the work turn to the angle the job needs without unclamping, and a locking base holds that angle under load. Check how the vise mounts as well: the GOEHNER package includes 4 bolts, and the Fasmov vise clips to a workbench or table for portable work.
Material and anvil
Materials here run from cast aluminum on the Fasmov vise to cast iron on the GOEHNER, AV Steel and sanheshun vises, with ductile iron on the Forward vise. The Forward and GOEHNER listings both state 60,000 PSI, while the AV Steel listing states 2,250 lbs clamping force and the Forward listing states 4,400 lbs clamping force. An anvil adds a surface for tapping work at the bench, and it is stated on the Forward, AV Steel and sanheshun vises, but not on the GOEHNER or Fasmov vises.
Warranty and what is stated
Only the AV Steel listing states a lifetime warranty, and the GOEHNER listing states 3-year factory services rather than a warranty term. The Forward, sanheshun and Fasmov listings state no warranty term. When a figure is missing, the listing does not publish it: treat a missing opening, throat depth or warranty as not stated, and confirm it with the maker before buying for a job that depends on it.
Before You Strike an Arc
- Check the jaw opening against the thickest work before mounting the vise, since opening varies across these picks.
- Check that the swivel base locks at the angle the job needs before starting work.
- Confirm the mounting hardware fits the bench, and that the vise sits firm with no lateral movement.
- Use pipe jaws only where the listing states them, and use the anvil only on vises that state one.
- Check the jaws on arrival where a listing states two figures, and plan around the table figure until confirmed.
FAQ for welders
What jaw width should a bench vise under $75 have?
Jaw widths among these picks run from 3 inch to 6 inch. A 3 inch jaw suits small parts work, while a 6 inch jaw suits wider brackets and larger pieces. Match the width to the work, and check the jaw opening too, since width alone does not set how thick a piece the vise can hold.
Can these vises hold pipe?
Some can, with stated ranges. The Forward listing states pipe capacity of 1/2 inch to 1 1/2 inch diameter, and the AV Steel listing states a pipe jaw range of 5/8 inch to 1-7/8 inch. The GOEHNER listing states pipe and flat jaws without a range, and the Fasmov listing states a cross pattern for wire and rods when the rubber jaws are removed.
What does a swivel base change?
A swivel base lets the vise turn so the work faces the angle the job needs, without unclamping and re-clamping. Bases here run from a 240 degree base to 360 degree bases, and the Forward and sanheshun listings state dual locking or double locking bases. A locking base matters most when the work gets hammered or filed, since a loose base lets the angle drift.
Is a cast iron vise better than a ductile iron vise?
The listings do not settle that question, and the figures are close on paper. The Forward ductile iron listing states 60,000 PSI, and the GOEHNER cast iron listing states 60,000 PSI as well. Compare the stated jaw figures, clamping force and warranty instead of the material name alone, since those figures decide what the vise can hold.
Which pick has a stated warranty?
Only the AV Steel pick states a lifetime warranty, against design, materials, and workmanship defects. The GOEHNER listing states 3-year factory services rather than a warranty term. The Forward, sanheshun and Fasmov listings state no warranty term, so a shop that wants a written warranty should start with the AV Steel pick.
Related: Swivel vs Fixed Welding Vise, Ductile Iron vs Cast Iron Bench Vise, Best Clamp On Bench Vise, Best Heavy Duty Bench Vise, and Bench Vise vs Welding Vise.
Scoring, line by line
Each vise is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing, and a warranty scores only where the listing states a concrete term.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| AV Steel 4-1/2 Inch Bench Vise | 9.6 | 27 | 20 | 20 | n/a | 4 |
| Forward 4 Inch Bench Vise | 9.6 | 32 | 22 | 21 | n/a | 0 |
| GOEHNER 6 Inch Bench Vise | 9.6 | 30 | 21 | 20 | n/a | 0 |
| sanheshun 6 Inch Bench Vise | 9.5 | 26 | 19 | 19 | n/a | 0 |
| Fasmov 3 Inch Table Vise | 9.4 | 23 | 16 | 19 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.





