Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best All Around Stick Welding Rod Under $25 (2026)

4 stick welding rods under 25, compared by rod type, diameter, length, pack size and stated strength.

Best All Around Stick Welding Rod Under $25 (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Metal Marlin E7018 H4RBest OverallMetal Marlin E7018 H4R9.5/10View on Amazon
  2. 2Metal Marlin E6011Best for Farm RepairsMetal Marlin E60119.5/10View on Amazon
  3. 3Buelkmag E6013Best for Thin SheetBuelkmag E60139.5/10View on Amazon
  4. 4Fox Alloy ENiFe-CI Ni55Best for Cast IronFox Alloy ENiFe-CI Ni559.3/10View on Amazon

A cracked bracket on the trailer, a rusty gate hinge, a thin duct panel that burns through if the arc lingers: stick welding earns its keep on exactly these jobs, and the rod in the stinger decides how the bead turns out. The best all around stick welding rod under 25 is the rod that handles mild steel, thin sheet and rusty metal without fuss, and still leaves room for a cast iron repair. This guide compares rods on the figures their listings state: rod type, diameter, length, pack size and stated strength.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Metal Marlin E7018 H4R: Low-hydrogen rod with 70,000 to 84,000 psi tensile strength, vacuum-packed, for structural steel and fabrication. Check price on Amazon
  • Best for Farm Repairs Metal Marlin E6011: Deep penetration on rusty, painted or oily metal, AC and DC, for farm equipment and field repairs. Check price on Amazon
  • Best for Thin Sheet Buelkmag E6013: 3/32 in rod with shallow penetration for thin metal sheets, ducts and fences, in a 6 lb pack. Check price on Amazon
  • Best for Cast Iron Fox Alloy ENiFe-CI Ni55: 55-percent nickel rod for gray cast iron and nodular cast iron, and for joining cast iron to steel. Check price on Amazon

The machines

Metal Marlin E7018 H4R Welding Rod 1/8”

Metal Marlin E7018 H4R Welding Rod 1/8”

METAL MARLIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A low-hydrogen 1/8 in rod in a 5 lb pack, with a stated tensile strength of 70,000 to 84,000 psi. The rods ship vacuum-packed to keep moisture out.

Pros

  • 70,000 to 84,000 psi tensile strength as stated
  • Low-hydrogen rod conforms to AWS A5.1 and ASME SFA-5.1
  • Vacuum-packed to keep moisture out, no pre-baking needed
  • All-position rod runs on AC and DC

Cons

  • No warranty term is stated on the listing
  • No safety listing is stated
  • 5 lb pack is smaller than the 6 lb E6013 pack
Metal Marlin E6011 Welding Rod 1/8″, 5 lb Pack

Metal Marlin E6011 Welding Rod 1/8″, 5 lb Pack

METAL MARLIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1/8 in E6011 rod in a 5 lb pack with deep penetration and a fast-freezing arc. The listing states AC and DC use, including small AC buzz box welders.

Pros

  • Deep penetration on rusty, painted or oily metal
  • Fast-freezing arc for all-position welding
  • Runs on AC and DC, including small AC buzz box welders
  • Vacuum-sealed packaging

Cons

  • No tensile strength figure is stated
  • No warranty term is stated on the listing
  • No safety listing is stated
  • 5 lb pack is smaller than the 6 lb E6013 pack
6013 welding rod 3/32 6LB Carbon Steel Sticks

6013 welding rod 3/32 6LB Carbon Steel Sticks

Buelkmag9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/32 in E6013 rod in a 6 lb pack for thin metal work. The listing states all-position welding with shallow penetration and minimal spatter.

Pros

  • 3/32 in diameter suits thin metal sheets
  • Shallow penetration avoids burning through thin metal
  • Minimal spatter with slag that peels off after cooling
  • 6 lb pack is the largest pack here

Cons

  • Shallow penetration limits the rod on thicker metal
  • No tensile strength figure is stated
  • No warranty term is stated on the listing
  • No safety listing is stated
ENiFe-CI 5pcs 55-Percent Nickel Cast Iron Welding

ENiFe-CI 5pcs 55-Percent Nickel Cast Iron Welding

Fox Alloy9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55-percent nickel cast iron rod, 1/8 in by 14 in, in a pack of 5. The listing states conformance to AWS A5.15 for repairing gray cast iron and nodular cast iron.

Pros

  • 55-percent nickel rod for cast iron repair
  • Joins cast iron to steel
  • Conforms to AWS A5.15 ENiFe-CI
  • Weld metal resists solidification cracking

Cons

  • Pack of 5 rods is the smallest pack here
  • A specialist rod for cast iron, not an all-around mild steel rod
  • No warranty term is stated on the listing
  • No safety listing is stated

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Rod type Diameter Length Pack Positions Stated standard
Metal Marlin E7018 H4R 9.5/10 E7018 low hydrogen 1/8 in 14 in 5 lb All positions AWS A5.1, ASME SFA-5.1
Metal Marlin E6011 9.5/10 E6011 1/8 in 14 in 5 lb All positions Not stated
Buelkmag E6013 9.5/10 E6013 3/32 in 14 in 6 lb All positions Not stated
Fox Alloy ENiFe-CI Ni55 9.3/10 ENiFe-CI Ni55 1/8 in 14 in 5 pcs Not stated AWS A5.15

Ratings in this table are the makers’ own claims taken from each product page (4 November 2026). Where a listing states a figure differently in the title and the spec table, the table shows the stated figures.

How to pick the best all around stick welding rod under 25

Rod type: 6013, 6011, 7018 and Ni55

Rod type sets the bead character. E6013 runs smooth on thin sheet with shallow penetration. E6011 digs deep on rusty, painted or oily metal with a fast-freezing arc. E7018 is the low-hydrogen rod for structural joints, with a stated tensile strength of 70,000 to 84,000 psi. ENiFe-CI Ni55 is the 55-percent nickel rod for cast iron. For all-around mild steel work, the choice sits between E6011 and E7018; E6013 suits thin work and Ni55 suits cast iron.

Diameter and length

Diameter sets the heat the rod carries. The E6013 rod here is 3/32 in, while the E6011, E7018 and Ni55 rods are 1/8 in. A 3/32 in rod suits thin sheet and small repairs; a 1/8 in rod suits general fabrication and thicker joints. All 4 rods here are 14 in long, so length does not separate them.

AC or DC, and the machine on the bench

A rod that runs on AC and DC fits any machine on the bench. The E6011 and E7018 listings state AC and DC use, and the E6011 listing names small AC buzz box welders. The E6013 listing states general purpose use on most household portable welding machines. The Ni55 listing states no power source, so check the machine before ordering.

Thin metal, rusty metal and cast iron

Match the rod to the metal in front of the welder. Thin sheet wants the E6013 rod: shallow penetration and minimal spatter keep the bead from burning through. Rusty, painted or oily metal wants the E6011 rod: deep penetration and a fast-freezing arc cut through the grime. Cast iron wants the Ni55 rod: a 55-percent nickel electrode made for gray cast iron and nodular cast iron. Structural joints want the E7018 rod: low hydrogen and a stated tensile strength of 70,000 to 84,000 psi.

Packaging and storage

Rod packaging decides whether the rods arrive dry. The E6011 listing states vacuum-sealed packaging, and the E7018 listing states vacuum packing that keeps moisture out with no pre-baking. The E6013 and Ni55 listings state no packaging detail. Pack size matters too: the E6013 pack is 6 lb, the E6011 and E7018 packs are 5 lb, and the Ni55 pack holds 5 pcs. Keep rods dry in the shop, and keep low-hydrogen rods sealed until use.

Before You Strike an Arc

  • Check the rod diameter against the machine: 3/32 in for the E6013 rod, 1/8 in for the E6011, E7018 and Ni55 rods.
  • Check the pack on arrival: 6 lb of E6013, 5 lb of E6011, 5 lb of E7018, and 5 pcs of Ni55.
  • Keep low-hydrogen rods dry: the E7018 rods ship vacuum-packed to keep moisture out.
  • Match the rod to the metal: Ni55 for cast iron, E6013 for thin sheet, E6011 for rusty metal, E7018 for structural joints.
  • Wear a helmet and gloves, ventilate the shop, and keep the work area clear of flammable material before striking an arc.

FAQ for welders

What is the best all around stick welding rod?

For mild steel work in the home shop, the choice sits between E6011 and E7018. E6011 digs deep on rusty metal and runs on AC and DC, while E7018 is the low-hydrogen rod for structural joints with a stated tensile strength of 70,000 to 84,000 psi. E6013 suits thin sheet, and Ni55 suits cast iron.

What is the difference between 6013, 6011 and 7018 rods?

E6013 is the smooth rod for thin sheet, with shallow penetration and minimal spatter. E6011 is the deep penetration rod for rusty, painted or oily metal, with a fast-freezing arc. E7018 is the low-hydrogen rod for structural joints, with a stated tensile strength of 70,000 to 84,000 psi.

Can I weld cast iron with a mild steel rod?

Cast iron wants a nickel rod, not a mild steel rod. The Ni55 listing states a 55-percent nickel electrode for repairing gray cast iron and nodular cast iron, and for joining cast iron to steel. Its weld metal resists solidification cracking, which is the reason to reach for the nickel rod on cast iron.

What diameter rod should I use?

Use 3/32 in for thin sheet and small repairs, and 1/8 in for general fabrication and thicker joints. The E6013 rod here is 3/32 in, while the E6011, E7018 and Ni55 rods are 1/8 in. Match the diameter to the metal thickness and the machine.

Do stick welding rods go bad?

Rods go bad when moisture gets into the flux, which is why packaging matters. The E7018 listing states vacuum packing that keeps moisture out with no pre-baking, and the E6011 listing states vacuum-sealed packaging. Keep rods dry in the shop and keep low-hydrogen rods sealed until use.

Related: the mig vs stick for rusty metal, the welding rods vs mig wire, the tig vs stick for farm repairs and our welding consumables hub. Also see our best welding rod bag and our mig vs stick for structural steel.

Scoring, line by line

Each rod earns points for performance, build, value, safety and warranty. How we pick explains the weights. None of the listings here states a safety listing, so safety earns no points across the picks. No listing here states a warranty term, so warranty earns no points either.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Metal Marlin E7018 H4R 9.5 32 22 21 0 0
Metal Marlin E6011 9.5 30 21 21 0 0
Buelkmag E6013 9.5 28 20 22 0 0
Fox Alloy ENiFe-CI Ni55 9.3 26 21 16 0 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides