Mig vs Stick for Structural Steel: Which One Should You Buy?
ER70S-6 MIG wire against E7018 stick rods for structural steel, compared on certifications, gas needs and listing contradictions, with a verdict for each side.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
2-Pack INEFIL ER70S-6 MIG Welding Wire .035"9.6/10View on Amazon - 2
2-Pack INEFIL ER70S-6 MIG Welding Wire .030"9.6/10View on Amazon - 3
E7018 Welding Rods 1/8'' 6LB Low Hydrogen Carbon9.5/10View on Amazon
Verdict. Pick MIG with the INEFIL ER70S-6 wire if you have a gas setup and want certified, all-position wire for structural frames; the .035 in 2-pack is the heavier-fab pick. Pick stick with the E7018 rods if you weld outdoors, but confirm the diameter and weight with the seller first, since the Buelkmag listing contradicts itself on both.
Structural steel asks a direct question: mig vs stick for structural steel. This comparison puts ER70S-6 MIG wire against E7018 stick rods on what each listing states, using two INEFIL wire listings and one Buelkmag rod listing as the examples. For mig vs stick for structural steel, the listings draw the line clearly.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The three picks

2-Pack INEFIL ER70S-6 MIG Welding Wire .035"
A 10 lb spool 2-pack of .035 in ER70S-6 MIG wire, AWS A5.18 classified, made in Italy.
Pros
- AWS A5.18 classified with third-party certifications
- All-position welding, single and multi-pass
- Rated for steels up to 510 MPa tensile
- Low spatter with manganese and silicon deoxidizers
Cons
- Requires shielding gas, C25 or CO2
- No warranty term is stated
- 2-pack of 10 lb spools is a lot of wire for small jobs

2-Pack INEFIL ER70S-6 MIG Welding Wire .030"
A 10 lb spool 2-pack of .030 in ER70S-6 MIG wire, AWS A5.18 classified, made in Italy.
Pros
- AWS A5.18 classified with third-party certifications
- All-position welding, single and multi-pass
- Low spatter, smoother bead appearance
- Feeds Miller, Lincoln, Hobart, ESAB and most MIG setups
Cons
- Requires shielding gas, C25 or CO2
- No warranty term is stated
- 2-pack of 10 lb spools is a lot of wire for small jobs

E7018 Welding Rods 1/8'' 6LB Low Hydrogen Carbon
E7018 low-hydrogen stick rods for load-bearing structures and heavy-duty structural repairs.
Pros
- Low-hydrogen E7018 for structural work
- All-position welding stated
- For load-bearing structures and thick steel plates
- AC/DC power source stated
Cons
- Title says 1/8 in, bullets say 3/32 in diameter
- Title says 6 lb, bullets say 3 pounds
- No warranty term is stated
- No certifications are stated
Other welders and gear to compare
Solid MIG Welding Wire ER70S-6 0.35 Inch 2LB SpoolCheck price on Amazon
ER308L .030" Stainless Steel MIG Welding Wire 10 lb SpoolCheck price on Amazon
Stainless Steel 316L MIG Welding Wire 2 Ibs .035" 1 RollCheck price on Amazon
ER70S-6 .023 In MIG Welding Wire 11 LBS Mild Steel MIG WireCheck price on Amazon
INEFIL ER70S-6 MIG Welding Wire .035"Check price on Amazon
1/8" Welding Rods E6013 Carbon Steel Stick ElectrodesCheck price on Amazon
Side by side
| INEFIL ER70S-6 .030 | INEFIL ER70S-6 .035 | Buelkmag E7018 1/8 | |
|---|---|---|---|
| Process | MIG | MIG | Stick |
| Diameter | .030 in (title) | .035 in (title) | 1/8 in (title), 3/32 in (bullets) |
| Pack | 10 lb spool, 2-pack | 10 lb spool, 2-pack | 6 lb (title), 3 lb (bullets) |
| Classification | AWS A5.18 | AWS A5.18 | E7018 |
| Shielding gas | C25 or CO2 | C25 or CO2 | Not stated |
| Position | All positions | All positions | All positions |
| Warranty | Not stated | Not stated | Not stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 23 October 2026. None of the three listings states a warranty term.
Mig vs stick for structural steel: certifications
Both INEFIL listings are AWS A5.18 classified and name third-party certifications: ABS, TUV, RINA, DNV-GL, Lloyd’s Register, CWB and CE. The Buelkmag E7018 listing states no certifications. For structural work where an inspector asks for paperwork, that gap matters. See also MIG vs stick for thick steel.
Shielding gas and setup
The INEFIL wires need shielding gas, C25 or CO2, and run DC+. The Buelkmag rods run AC or DC with no gas stated. MIG with gas is sensitive to wind; the stick listing states no gas at all. If the work is outside, that can tip the choice toward stick.
Diameter contradictions
Both INEFIL titles state the wire diameter (.030 in and .035 in) while both spec tables say 0.023 in; we trust the titles. The Buelkmag title says 1/8 in and 6 lb while its bullets say 3/32 in and 3 pounds; the title and bullets disagree, so the listing leaves both unclear. Confirm before you buy.
Choose MIG if
- You have a gas setup and weld structural frames, trailers or tanks.
- You want AWS A5.18 wire with named third-party certifications.
- You weld in a shop, out of the wind.
- All-position, multi-pass work is the job.
Choose stick if
- You weld outdoors where gas would blow away.
- You have an AC/DC machine and no gas bottle.
- You want low-hydrogen E7018 rods for load-bearing repairs.
- You can confirm the rod diameter and weight with the seller first.
FAQ for welders
Is MIG or stick better for structural steel?
It depends on the job. The INEFIL listings offer certified, all-position ER70S-6 wire for structural frames, while the E7018 rods suit outdoor and heavy repair work. Pick the process that fits the site and the machine you own.
What does AWS A5.18 mean on the INEFIL wire?
It is the classification the listing states for the wire, with third-party certifications including ABS, TUV, RINA, DNV-GL, Lloyd’s Register, CWB and CE. The Buelkmag listing states no certifications.
Do I need gas for the INEFIL wire?
Yes. Both listings state shielding gas is required: C25 or CO2, with DC+ polarity.
What diameter are the Buelkmag rods?
The listing leaves it unclear: the title says 1/8 in and the bullets say 3/32 in. The weight is also unclear: 6 lb in the title against 3 pounds in the bullets. Confirm with the seller before you buy.
Can the INEFIL wire weld overhead?
Both listings state all-position welding: flat, horizontal, vertical and overhead.
Related: best MIG wire for thick steel, 030 vs 035 MIG wire, MIG vs stick for auto body, and the welding consumables hub.
Scoring, line by line
All three are scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| INEFIL ER70S-6 .035 | 9.6 | 32 | 21 | 20 | n/a | 0 |
| INEFIL ER70S-6 .030 | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Buelkmag E7018 1/8 | 9.5 | 27 | 19 | 19 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.
Before you strike an arc. Wear a helmet with the right shade, safety glasses underneath, leather gloves and flame resistant clothing. Weld with good ventilation, clear anything flammable from the area, and keep an extinguisher close. See the OSHA welding overview and our Safety Disclaimer.




