Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best 120V Plasma Cutter (2026): 4 Picks for Home Shops

Four 120V plasma cutters for home shops, compared on amps, cut thickness, duty cycle, air needs and warranty, plus who should skip each.

Best 120V Plasma Cutter (2026): 4 Picks for Home Shops
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARCCAPTAIN CUT55Best OverallARCCAPTAIN CUT559.6/10View on Amazon
  2. 2Hobart AirForce 12ciBest with Built-In AirHobart AirForce 12ci9.3/10View on Amazon
  3. 3Reboot RBC6000DBest ValueReboot RBC6000D9.5/10View on Amazon
  4. 4GNI CUT-60PROBest 2-in-1GNI CUT-60PRO9.4/10View on Amazon

A bracket cracked on the trailer, a patch panel rusted through, a bracket to cut from plate: a plasma cutter turns a household outlet into a cutting torch for steel, stainless and aluminum. The best 120v plasma cutter in this guide is a machine that runs on a standard 120V outlet and cuts sheet and plate without a gas bottle or an oxy-fuel rig.

Three of the four cutters here run on dual voltage, 120V and 240V, and one runs on 120V only. One has a built-in air compressor, one adds a stick welder, and one is controlled from an app. The scores follow what each listing states and what it leaves out.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall ARCCAPTAIN CUT55: 55A, app control, air pressure detection, a 7/8 inch max cut at 240V and a 3-year warranty. Check price on Amazon
  • Best with Built-In Air Hobart AirForce 12ci: 120V only with a built-in air compressor, no external air needed, and a 5-3-1 warranty. Check price on Amazon
  • Best Value Reboot RBC6000D: 60A dual voltage, a 5/8 inch severance cut, a 50% duty cycle and a 14.92 lb body. Check price on Amazon
  • Best 2-in-1 GNI CUT-60PRO: 60A plasma cutter plus stick welder, non-touch pilot arc, pre-installed regulator and 2T/4T. Check price on Amazon

The machines

ARCCAPTAIN iControl CUT55 Prolux Plasma Cutter

ARCCAPTAIN iControl CUT55 Prolux Plasma Cutter

ARCCAPTAIN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55A dual-voltage plasma cutter with app control, air pressure detection and a 7/8 inch max cut, with a 3-year warranty.

Pros

  • 55A with a 7/8 inch max cut at 240V
  • App control up to 10 meters
  • Air pressure detection with a 0.3 to 0.55 MPa range
  • 3-year warranty stated

Cons

  • No duty cycle stated
  • 120V cut is 9 to 12 mm, thinner than the 240V range
  • Expanded metal and rust removal need a mode switch first
  • No consumable model stated
Reboot Plasma Cutter, 60 Amps Plasma Cutter

Reboot Plasma Cutter, 60 Amps Plasma Cutter

Reboot9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60A dual-voltage plasma cutter with a 5/8 inch severance cut, a 1/2 inch clean cut and a 50% duty cycle.

Pros

  • 60A with a 5/8 inch severance cut and a 1/2 inch clean cut
  • Dual voltage with auto-detection, 10 to 35A at 120V
  • 50% duty cycle stated
  • PSI guidance of 70 to 75 PSI in the listing

Cons

  • No warranty stated
  • Touch arc starting, the torch must touch the plate
  • Requires 90 PSI and 60 L/min or above
  • No 120V cut thickness stated
GNI 60Amp Portable Plasma Cutter/Stick Welder 2

GNI 60Amp Portable Plasma Cutter/Stick Welder 2

GNI9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60A plasma cutter and stick welder in one, with a non-touch pilot arc, a pre-installed regulator and 2T/4T control.

Pros

  • 60A plasma cutter plus 140A stick welder in one machine
  • Non-touch pilot arc
  • Pre-installed air regulator with a 1/4 inch NPT quick-connect
  • 2T/4T with PA and PT adjustable from 2 to 15 seconds

Cons

  • Model reads CUT-50PRO in one place and CUT-60PRO in another
  • No warranty stated
  • Compressor sold separately
Hobart AirForce 12ci Plasma Cutter 120V

Hobart AirForce 12ci Plasma Cutter 120V

Hobart9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 120V plasma cutter with a built-in air compressor, so no external air is needed, with a 5-3-1 warranty.

Pros

  • Built-in air compressor, no external air needed
  • 120V only, runs on household power
  • 5-3-1 warranty stated
  • Made in the United States

Cons

  • No amps stated
  • No cut thickness stated
  • No duty cycle stated
  • 29 lb, the heaviest here

Other welders and gear to compare

Best 120v plasma cutter compared

Model Gear Score Amps 120V cut Max cut Air Weight Warranty
ARCCAPTAIN CUT55 9.6/10 55A 9-12 mm 7/8 in (22 mm) at 240V 0.3-0.55 MPa (57.5 PSI) 19.84 lb 3 years
Reboot RBC6000D 9.5/10 60A Not stated 5/8 in severance, 1/2 in clean 90 PSI, 60 L/min 14.92 lb Not stated
GNI CUT-60PRO 9.4/10 60A 2/5 in (10 mm) clean 4/5 in (20 mm) 90 PSI, 2.1 CFM 11 lb (bullets), 20.7 lb (table) Not stated
Hobart AirForce 12ci 9.3/10 Not stated Not stated Not stated Built-in compressor 29 lb 5-3-1

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 10 October 2026.

Buying guide: what matters in a 120V plasma cutter

Amps and cut thickness

Stated amps run from 55A to 60A, and the Hobart listing states no amps. Cut thickness is stated with its voltage: the ARCCAPTAIN cuts 9 to 12 mm at 120V and up to 7/8 inch at 240V, the GNI cuts 2/5 inch clean at 120V and 35A, and the Reboot states a 1/2 inch clean cut at 240V and 60A. The Hobart listing states no cut thickness.

Duty cycle

Only the Reboot listing states a duty cycle, 50%. The other three listings state no duty cycle, so there is nothing to compare on sustained cutting.

Air supply

A plasma cutter needs clean, dry air at the right pressure. The Hobart has a built-in compressor and needs no external air. The Reboot needs 90 PSI and 60 L/min or above, and the GNI needs 90 PSI and 2.1 CFM, with a pre-installed regulator. The ARCCAPTAIN states an air pressure detection range of 0.3 to 0.55 MPa. See what size air compressor do I need for a plasma cutter for sizing.

Pilot arc or touch arc

The GNI and ARCCAPTAIN listings state a non-touch pilot arc, which strikes without touching the plate. The Reboot uses a touch arc start, so the torch head must touch the metal plate. The Hobart listing states no arc start type.

Breakers and household power

The Reboot listing states a 50A breaker for 120V and a 30A breaker for 240V. The other listings state no breaker size. A 120V cutter still needs a circuit that can carry its draw, so check the breaker before ordering.

Use as directed. Plasma cutting throws sparks, hot slag and fumes, so wear a welding helmet, gloves and flame-resistant clothing, keep flammables clear of the cut, and cut in ventilated air. Never cut galvanized steel without ventilation and a respirator rated for the fumes.

Before You Strike an Arc

  • Power: the Hobart runs on 120V only; the other three run on 120V and 240V, with auto-detection stated for the Reboot and GNI.
  • Air: the Hobart needs no external air; the Reboot needs 90 PSI and 60 L/min or above, and the GNI needs 90 PSI and 2.1 CFM.
  • Consumables: the Reboot listing names PT31 consumables; the other listings name no consumable model.
  • Breaker: the Reboot listing states a 50A breaker for 120V; the other listings state no breaker size.
  • On arrival: check the GNI weight and model number against the listing, since the bullets and the spec table disagree.

FAQ for welders

Can a plasma cutter run on a standard household outlet?

The Hobart AirForce 12ci runs on 120V only. The other three run on 120V and 240V. The Reboot listing states a 50A breaker for 120V, so check the circuit the cutter will run on.

Do I need an air compressor for a plasma cutter?

Three of the four need one: the Reboot needs 90 PSI and 60 L/min or above, and the GNI needs 90 PSI and 2.1 CFM. The Hobart has a built-in compressor and needs no external air. The ARCCAPTAIN listing states an air pressure detection range but no compressor requirement.

What thickness can a 120V plasma cutter cut?

It depends on the machine and the voltage: the ARCCAPTAIN states 9 to 12 mm at 120V, and the GNI states a 2/5 inch clean cut at 120V and 35A. The Reboot states its clean cut at 240V, not 120V, and the Hobart states no thickness.

What is the difference between a pilot arc and a touch arc start?

A non-touch pilot arc strikes without touching the plate, per the ARCCAPTAIN and GNI listings. A touch arc start needs the torch head to touch the metal plate, per the Reboot listing. The Hobart listing states no arc start type.

Can a plasma cutter also weld?

One here can: the GNI is a 2-in-1 plasma cutter and stick welder, with stick mode from 15 to 140A for 1/16 to 1/8 inch rods. The other three listings state cutting only.

Related: the plasma cutters hub, 120v vs 240v plasma cutter, dual voltage vs 110v plasma cutter and pilot arc vs high frequency plasma cutter. Also see our best inverter plasma cutter and best consumables for plasma cutter.

Scoring, line by line

Each cutter is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. No listing here states a UL, ETL or CSA listing, so every cutter here scores zero on safety; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
ARCCAPTAIN CUT55 9.6 32 21 20 0 3
Reboot RBC6000D 9.5 30 20 21 0 0
GNI CUT-60PRO 9.4 30 20 19 0 0
Hobart AirForce 12ci 9.3 22 20 18 0 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.

More buying guides