7018 vs 8018 Welding Rod: Which One Should You Buy?
7018 vs 8018 welding rod: the compared listings are all E7018 low-hydrogen rods, so this guide ranks the 7018 side on stated specs and marks the 8018 side as not covered.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Hobart 7018 Stick Welding Electrode 3/32 in9.5/10View on Amazon - 2
Victory Welding Alloys 6010 Welding Rod 5/32" E6010 5/32" 59.6/10View on Amazon - 3
ATLASWELDER 7018 Welding Rod 3/32" 10LB9.5/10View on Amazon - 4
ARCCAPTAIN E7018 Welding Rod 3/32" 10LB Low Hydrogen CarbonView on Amazon - 5
ATLASWELDER 7018 Welding Rod 1/8" 10LBView on Amazon - 6
PGN E7018 Welding Rod 3/32" 10LBView on Amazon - 7
Victory Welding Alloys 7018 Welding Rod 1/8" E7018 1/8" 5View on Amazon
A cracked frame bracket on the bench calls for a low-hydrogen stick rod, and the designation on the box is the first check for whether the rod matches the job. This guide answers 7018 vs 8018 welding rod from the listings compared here: the rods compared are all E7018 low-hydrogen rods, so the 7018 side is covered in detail and the 8018 side has no listing among them to score. If the job calls for an 8018 rod, none of the rods below is one, so check the designation printed on the box before buying.
Other welders and gear to compare
ARCCAPTAIN E7018 Welding Rod 3/32" 10LB Low Hydrogen CarbonCheck price on Amazon
ATLASWELDER 7018 Welding Rod 3/32" 10LBCheck price on Amazon
ATLASWELDER 7018 Welding Rod 1/8" 10LBCheck price on Amazon
PGN E7018 Welding Rod 3/32" 10LBCheck price on Amazon
Victory Welding Alloys 7018 Welding Rod 1/8" E7018 1/8" 5Check price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The difference in one paragraph
The listings draw the 7018 side clearly: low-hydrogen electrodes for stick welding, stated for all positions, with stable arcs and low spatter as the makers claim. Iron powder is stated for the ARCCAPTAIN and LIIJII listings, not for every listing here. The 8018 side has no listing here, so no diameter, length, pack weight or polarity can be stated for it from this comparison. That gap is the main finding: buy a 7018 rod from the listings below only when the job calls for a 7018 rod, and treat any 8018 claim without a listing behind it as unverified.
Side by side
| Rod | Diameter | Length | Pack weight | Polarity |
|---|---|---|---|---|
| ARCCAPTAIN E7018 | 3/32 inch | 14 inches | 10 lb | AC or DC reverse polarity |
| LIIJII E7018 | 1/8 inch | 14 inches | 2 lb | AC and DC reverse polarity (DCEP) |
| ATLASWELDER 7018 | 3/32 inch | 14 inches | 10 lb | Not stated |
| Buelkmag E7018 | 3/32 inch | 14 inches | 3 pounds | Not stated |
Pack weights and diameters are taken from each listing’s title and bullets; where a listing names variants, the table uses the title size.
7018 vs 8018 welding rod: the rods, ranked
Ranked by how completely each listing states its specs, the rods line up as follows.
| Rod | Diameter | Length | Pack weight | Polarity stated |
|---|---|---|---|---|
| ARCCAPTAIN E7018 | 3/32 inch | 14 inches | 10 lb | AC or DC reverse polarity |
| LIIJII E7018 | 1/8 inch | 14 inches | 2 lb | AC and DC reverse polarity (DCEP) |
| ATLASWELDER 7018 | 3/32 inch | 14 inches | 10 lb | Not stated |
| Buelkmag E7018 | 3/32 inch | 14 inches | 3 pounds | Not stated |
ARCCAPTAIN E7018 leads the ranking because its listing states the full set: 3/32 inch diameter, 14 inches length, 10 lb pack, iron powder low-hydrogen electrode, any position on AC or DC reverse polarity, with high-quality X-ray welds as the maker claim. Its stated uses run from steel structures and frames to high-pressure pipelines, oil pipelines, ship hulls and steel bridges.
LIIJII E7018 follows with the clearest compliance claim: AWS A5.1 E7018 standards, low-hydrogen potassium iron powder flux, 1/8 inch diameter by 14 inches length in a 2 lb sealed plastic box, AC and DC reverse polarity (DCEP), all positions, and X-ray quality deposits with slag that peels off easily.
ATLASWELDER 7018 states 3/32 inch and 10 lb in its title and spec table, with all positions from flat to overhead, smooth beads, minimal spatter, slag release and impact resistance. Its listing is less clean: the bullets also name a 1/8 inch diameter and 5 LB and 10 LB packs as available, and the model name adds E6013 beside E7018, so confirm the exact rod before ordering.
Buelkmag E7018 states 3/32 inch diameter, 14 inches length and 3 pounds, with all-position welding, moderate deep penetration and ultra-low spatter for load-bearing structures, thick steel plates, equipment bases and frame fabrication. It states no polarity and no AWS compliance, which puts it last on stated specs.
Polarity and positions
Polarity is stated on the ARCCAPTAIN and LIIJII listings: ARCCAPTAIN states AC or DC reverse polarity, and LIIJII states AC and DC reverse polarity (DCEP). ATLASWELDER and Buelkmag state no polarity. All listings state all-position welding, with ATLASWELDER naming flat, horizontal, vertical and overhead positions.
Listing gaps to check
The gaps to check before ordering:
- ATLASWELDER: the bullets name a 1/8 inch diameter and 5 LB and 10 LB packs as available, against a 3/32 inch and 10 lb title, and the model name adds E6013 beside E7018.
- No warranty: none of the listings states a warranty term, so no warranty claim is made for any rod here.
- No polarity: ATLASWELDER and Buelkmag state no polarity, so check the listing if the machine runs one polarity only.
- No 8018 listing: none of the listings states an 8018 designation, so the 8018 side cannot be scored from this comparison.
Stick welding safety. Stick welding throws spatter and fumes: weld with ventilation, wear a helmet and gloves, and clear flammables from the area.
FAQ for welders
Can a 7018 rod handle structural work?
The listings say yes for their rods: ARCCAPTAIN names steel structures, frames, high-pressure pipelines, ship hulls and steel bridges, and ATLASWELDER names bridges, pressure vessels and structural fabrication. Match the rod to the job and follow the welding procedure for the joint.
What diameters of 7018 rod are listed here?
The listings state 3/32 inch and 1/8 inch diameters. ARCCAPTAIN, Buelkmag and ATLASWELDER state 3/32 inch in their titles, while LIIJII states 1/8 inch.
Do these rods run on AC and DC?
ARCCAPTAIN states AC or DC reverse polarity, and LIIJII states AC and DC reverse polarity (DCEP). ATLASWELDER and Buelkmag state no polarity, so check the listing before buying for a machine that runs one polarity only.
Is there an 8018 rod among these listings?
No. Every listing here states an E7018 designation, and none states an 8018 designation. A buyer who needs an 8018 rod needs a listing that states it.
What pack weights are listed?
ARCCAPTAIN and ATLASWELDER state 10 lb in their titles, Buelkmag states 3 pounds, and LIIJII states 2 lb. ATLASWELDER bullets also name a 5 LB pack as available.
Related: best all-around stick welding rod, best stick welder for farm use, and the stick welders hub. Also see the welding consumables hub.




