1/8 vs 3/16 Welding Rod: Which One Should You Buy?
1/8 vs 3/16 welding rod: a direct diameter answer plus four 1/8 in rod listings compared by rod type, position and pack size.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Victory Welding Alloys 6010 Welding Rod 5/32" E6010 5/32" 59.6/10View on Amazon - 2
50 lb Steel Can E6010 5/32" Stick electrodes welding rod9.6/10View on Amazon - 3
Forney 31105 E6011 Welding Rod9.6/10View on Amazon - 4
TOOLIOM E6011 Welding Rod Carbon Steel Stick ElectrodesView on Amazon - 5
TOOLIOM E7018 Welding Rod Low-Hydrogen Stick ElectrodesView on Amazon - 6
Victory Welding Alloys 6010 Welding Rod 1/8" E6010 1/8" 5View on Amazon - 7
Victory Welding Alloys 6011 Welding Rod 1/8" E6011 1/82" 5View on Amazon - 8
ATLASWELDER 6013 Welding Rod 1/8" 10LBView on Amazon - 9
ATLASWELDER 6013 Welding Rod 1/8" 5LBView on Amazon
1/8 vs 3/16 welding rod: pick 1/8 in for thinner stock, lower amperage machines and all-position work; pick 3/16 in for thicker stock where the extra metal deposit matters. The four listings here are all 1/8 in examples: E6011 and E7018 and 6010 rods in 5 and 10 lb packs. This guide answers the diameter question directly, then shows what the 1/8 in listings tell you.
Other welders and gear to compare
TOOLIOM E6011 Welding Rod Carbon Steel Stick ElectrodesCheck price on Amazon
TOOLIOM E7018 Welding Rod Low-Hydrogen Stick ElectrodesCheck price on Amazon
Victory Welding Alloys 6010 Welding Rod 1/8" E6010 1/8" 5Check price on Amazon
Victory Welding Alloys 6011 Welding Rod 1/8" E6011 1/82" 5Check price on Amazon
ATLASWELDER 6013 Welding Rod 1/8" 10LBCheck price on Amazon
ATLASWELDER 6013 Welding Rod 1/8" 5LBCheck price on Amazon
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
1/8 vs 3/16 welding rod: the diameter answer
Rod diameter sets the deposition rate and the amperage window. A 1/8 in rod runs at lower amperage and suits thinner material and all-position work; a 3/16 in rod deposits more metal per pass and suits thicker material at higher amperage. Match the rod to the material thickness and to what your machine can drive: a small inverter that tops out low will not drive 3/16 in rods, and 3/16 in on thin sheet will burn through.
The 1/8 in examples
| Rod | Type | Diameter | Pack | Positions |
|---|---|---|---|---|
| TOOLIOM E6011 | E6011 | 1/8 in | 5 lb | All |
| TOOLIOM E7018 | E7018 | 1/8 in | 10 lb | All |
| ARCCAPTAIN E7018 | E7018 | 1/8 in | 5 lb, 14 in | All |
| Victory 6010 | 6010 | 1/8 in | 5 lb | All |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 20 October 2026. “Not stated” means the listing does not give the figure. No 3/16 in example is listed here; the comparison below covers the four 1/8 in rods.
Rod types in the listings
The TOOLIOM E6011 is the AC-focused pick: an all-position mild steel electrode designed primarily for AC power sources, with excellent arc power and fast solidification of the weld metal, stated to weld poorly grooved, rusted or oily steels. The Victory 6010 is the penetration pick: a strong forceful arc creating deeply penetrating welds, with fast-freeze characteristics for any position including vertical-up, vertical-down, overhead, flat and horizontal, producing x-ray quality deposits with easily removable slag. The two E7018 listings are the low-hydrogen picks: the TOOLIOM 10 lb pack and the ARCCAPTAIN 5 lb pack, both 1/8 in, for AC and DC all-position welding of carbon, mild and low-alloy steels, with high tensile strength and good crack resistance for structural work like I-beams and angle iron.
When 1/8 in is the answer
Pick 1/8 in when the stock is thin to medium, when the machine is a smaller inverter, and when the welds are out of position. All four listings state all-position capability. The 5 lb packs (TOOLIOM E6011, ARCCAPTAIN E7018, Victory 6010) suit occasional work; the TOOLIOM E7018 10 lb pack suits the shop that burns rods steadily. The TOOLIOM E6011, TOOLIOM E7018 and ARCCAPTAIN listings all state 14 in length; the Victory 6010 states no length.
When 3/16 in is the answer
Pick 3/16 in for thicker stock and higher amperage machines, where fewer passes and more deposit per pass save time. No 3/16 in listing is covered here, so check the diameter your machine and material demand before buying. The same rod-type logic applies at 3/16 in: the 6010 listing is the penetration pick here, the E6011 listing states it welds rusted or oily steels, and the E7018 listings are the low-hydrogen structural pick.
Amperage and machines
Diameter and amperage move together: the larger the rod, the more amperage it wants. A 1/8 in rod suits a mid-range inverter; a 3/16 in rod wants a machine with the amperage headroom to drive it. The TOOLIOM listings state recommended amperages: 75 to 125 A for the E6011 and 115 to 165 A for the E7018. The ARCCAPTAIN and Victory listings state no range, so check the rod pack and the machine manual together. Running a rod below its range gives a sputtering arc; running it above gives spatter and undercut.
Passes and deposition
The real cost of the wrong diameter is passes. A 3/16 in rod deposits more metal per pass, so thick joints need fewer passes; a 1/8 in rod on thick stock means more passes and more interpass cleaning. The listings state no deposition figures, so this is the general trade-off the diameter names: 1/8 in for control and position, 3/16 in for volume.
Storage and moisture
The E7018 listings are low-hydrogen rods, and low-hydrogen means moisture-sensitive: the TOOLIOM and ARCCAPTAIN both state low-hydrogen flux formulations for crack-resistant structural welds. The listings state no storage instructions, but the rod type names the rule: keep low-hydrogen rods dry, and consider a rod oven for critical welds. The cellulosic 6010 and E6011 listings are less fussy about moisture, which is part of why the TOOLIOM E6011 states it welds rusted or oily steels.
Pack sizes and buying in bulk
The listings come in 5 and 10 lb packs: the TOOLIOM E6011, ARCCAPTAIN E7018 and Victory 6010 are 5 lb, and the TOOLIOM E7018 is 10 lb. Three of the four state 14 in length; the Victory 6010 states no length. For the occasional repair, 5 lb is enough rod for a long time; for the shop that burns rods steadily, the 10 lb pack is the larger pack.
The cellulosic vs low-hydrogen choice
The four listings split into two families. The E6011 and 6010 are the cellulosic family: forceful arcs, deep penetration, fast-freeze characteristics for all positions, and tolerance for rusted or oily steel. The two E7018 listings are the low-hydrogen family: iron powder flux, high tensile strength, crack resistance and x-ray quality deposits for structural and fabricating steels. The diameter question sits on top of this one: pick the family by the weld, then the diameter by the stock. A 1/8 in 7018 and a 3/16 in 7018 are both low-hydrogen rods; the family choice does not change with diameter.
Warranty and certifications
No listing here states a warranty term. No listing states an AWS certification in the text given; compare on rod type, diameter and pack size.
FAQ for welders
Which diameter for a beginner?
1/8 in: it runs at lower amperage, suits thinner stock and all four listings here state all-position use.
Which rod for rusty or oily steel?
The E6011 or 6010 listings: the TOOLIOM E6011 states it welds rusted or oily steels, and the Victory 6010 states deep penetration.
Which rod for structural welds?
The E7018 listings: low hydrogen, high tensile strength, stated for structural and fabricating steels.
How long are the rods?
The TOOLIOM E6011, TOOLIOM E7018 and ARCCAPTAIN listings all state 14 in. The Victory 6010 states no length.
Do any state a warranty?
None of the four listings states a warranty term.
Related: the best 7018 welding rod, the 6011 vs 7018 welding rod and the best small inverter stick welders.




