Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Yost LV-4 Review: Pros, Cons & Who It’s For

A Yost LV-4 review from the listing: a 4.5-inch homeowner bench vise with swivel base, pipe jaws and 30,000 PSI iron, plus spec gaps and who it fits.

Yost LV-4 Review: Pros, Cons & Who It’s For
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Yost LV-4 Homeowner's Vise, 4.5 Inch Jaw WidthYost LV-4 Homeowner's Vise, 4.5 Inch Jaw Width9.6/10View on Amazon
  2. 2Yost Vises COV-3 Clamp-On ViseYost Vises COV-3 Clamp-On ViseView on Amazon
  3. 3Yost Vises ADI-6 Heavy Duty ViseYost Vises ADI-6 Heavy Duty ViseView on Amazon
  4. 4Yost Vises LDPV-6 Drill Press ViseYost Vises LDPV-6 Drill Press ViseView on Amazon

When you are clamping angle iron for a fit-up, holding square tube for a bevel cut, or securing round bar on the welding bench, a sturdy bench vise is essential. This yost lv-4 review looks at whether Yost’s 4.5-inch homeowner vise can handle those shop holding tasks. Yost lists a 4.5-inch jaw width, a 3-inch jaw opening, a 240-degree swivel base, and a 30,000 PSI gray iron casting on a 9-pound body. We have not used this vise ourselves; this review is based on Yost’s Amazon listing for the LV-4 and the specs published there.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The vise

Yost LV-4 Homeowner's Vise, 4.5 Inch Jaw Width

Yost LV-4 Homeowner's Vise, 4.5 Inch Jaw Width

Yost Tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4.5-inch homeowner bench vise with a listed 30,000 PSI gray iron casting, featuring a 3-inch jaw opening, built-in pipe jaws, a 240-degree swivel base, and an anvil work surface.

Pros

  • Listing claims 30,000 PSI gray iron casting with serrated jaws
  • Swivel base rotates 240 degrees for angled workbench positioning
  • Built-in pipe jaws handle round stock from 0.6 to 1.85 inches in diameter
  • Includes a 3.5 by 2.7 inch anvil work surface for light shaping

Cons

  • Mounting hardware is not included in the box
  • Lightweight 9-pound body is not intended for heavy hammering or severe plate bending

Other welders and gear to compare

Yost LV-4 review: the short verdict

The LV-4 is a light-duty homeowner bench vise designed for home workshops and garage workbenches. The listing describes it as a home vise built from 30,000 PSI gray iron castings, fitted with a 240-degree swivel base, serrated jaws, pipe jaws, and a small anvil work surface. The model number on the listing is LV-4.

Three stated features support the case for light shop tasks. First, the 4.5-inch jaw width and 3-inch jaw opening provide adequate clamping room for small brackets, flat bar, and light tubing. Second, the built-in pipe jaws handle round stock from 0.6 inches to 1.85 inches in diameter, which keeps pipe from rolling during cuts or cleanup. Third, the swivel base rotates 240 degrees, allowing you to swing longer metal stock away from bench walls and tool racks.

The weak points lie in listing contradictions and omitted hardware. The bullet points claim 30,000 PSI gray iron, while the specification table lists tensile strength at 500 psi. Throat depth is listed as 2.6 inches in the bullets but 2.375 inches in the table. Mounting hardware is not included, and the maker cautions against overtightening to avoid damage. At 9 pounds, it is sized for light clamping and filing, not heavy sledgehammer bending.

Key specs

Model Jaw Width Jaw Opening Swivel Base
Yost LV-4 4.5 in 3 in 240°

All specs here repeat what the maker rates and the listing prints, copied down 14 October 2026. Jaw width is the width of the jaw face, jaw opening measures maximum opening distance, and throat depth measures clearance from the top of the jaws to the main screw body.

What the Yost LV-4 does well

Swivel base for angled fit-up

A swivel base allows you to adjust workpiece angle without unclamping the metal. The listing specifies that the LV-4 head rotates 240 degrees on its base and locks down with a swivel base lock. When you are filing bevels on square tube or preparing pipe for a tack weld, turning the vise head keeps long pieces clear of wall studs and adjacent tools. When arranging your workspace, positioning the vise near a sturdy bench corner gives you clearance to rotate workpieces freely.

Built-in pipe jaws for round tubing

Clamping round pipe in flat vise jaws often results in slippage or marred metal surfaces. The LV-4 incorporates cast-in pipe jaws beneath the primary clamping jaws. Yost lists a minimum pipe capacity of 0.6 inches diameter and a maximum of 1.85 inches diameter. That range covers small conduit, round tubing, and small pipe, holding them securely while you deburr cut edges or fit joints. For joint prep tips, our how to bevel metal for welding guide covers angle and edge shaping.

Compact dimensions for small workbenches

With listed item dimensions of 11 by 7.5 by 11 inches and a weight of 9 pounds, the LV-4 fits onto smaller garage benches and portable stands where a massive industrial cast vise would overcrowd the surface. The 4.5-inch jaw width and 3-inch jaw opening cover routine shop tasks like clamping flat bar, holding brackets for wire brushing, and securing small weldments. Serrated jaws provide positive bite on mill scale and raw bar stock, preventing workpieces from twisting during light work.

Anvil work surface for light tapping

The listing highlights an integrated anvil work surface measuring 3.5 inches by 2.7 inches, or 8.9 centimeters by 6.9 centimeters. This flat surface provides a convenient spot on the back of the vise body for light tapping, driving pins, flattening small tabs, or chipping weld slag off small brackets. Because it is part of a 9-pound gray iron casting, it is meant for light shop work rather than heavy blacksmithing with a cross-peen hammer.

Limitations

  • Mounting hardware is omitted: the listing notes that mounting hardware is not included, and it does not state bolt diameters or hole spacing, so measure the base before heading to the hardware store.
  • Listing contradictions on strength and depth: the bullet points claim 30,000 PSI gray iron while the spec table lists 500 psi tensile strength. Throat depth is also contradictory, listed as 2.6 inches in bullets and 2.375 inches in the table.
  • Lightweight 9-pound casting: at 9 pounds, the LV-4 is built for homeowner bench tasks. It lacks the mass required for bending heavy plate or taking repeated strikes from a heavy hammer.
  • Light clamping duty: the maker explicitly cautions against overtightening to avoid damaging the workpiece or vise casting, reflecting its light homeowner design.
  • Limited 3-inch opening: a 3-inch jaw opening limits you to smaller stock. Fabricators clamping thick box tubing or wide structural channel will need larger clamping solutions.

How we scored it

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Yost LV-4 9.6 28 18 20 n/a 3

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

The Gear Score weighs performance, build, value, safety and warranty, as explained on our how we pick page. The Yost LV-4 scores reasonably on performance and value for a homeowner bench tool with swivel capability and pipe jaws. Build score is reduced due to contradictory strength and dimension specs in the listing. Safety scores zero because safety certifications apply to powered machinery and PPE rather than unpowered bench vises, and none is listed. Warranty reflects the stated lifetime tech support.

Who should buy the Yost LV-4, and who should skip it

Buy it if

  • You need a compact vise on a home bench for light assembly, cleaning welds, and holding small parts.
  • You regularly clamp round pipe or tubing between 0.6 inches and 1.85 inches in diameter.
  • You want a 240-degree swivel base to adjust workpiece angles on a crowded bench.
  • You already have mounting fasteners and a workbench top ready for drilling.

Skip it if

  • You need a heavy vise for striking cold steel or bending structural angle iron.
  • Your fabrication projects frequently exceed the 3-inch jaw opening.
  • You need an industrial bench vise designed for continuous heavy fabrication.

Alternatives

  • Heavier fabrication table vises: our best welding vise for table roundup compares heavy-duty vises engineered for demanding shop fabrication.
  • Shop clamping options: if you need to clamp assemblies directly to tabletop surfaces, explore our types of welding clamps guide for alternatives.
  • Workbench setups: pairing your vise with a stable metal surface is essential; our best welding table for home shop guide reviews durable rolling and folding options.

Before You Strike an Arc

  • Inspect the gray iron casting and screw threads upon unboxing for shipping damage, binding, or casting voids before mounting.
  • Verify your workbench top thickness and measure the mounting hole pattern, since mounting hardware is not included in the box.
  • Check that the 240-degree swivel base lock secures firmly so the vise does not slip under lateral filing pressure.
  • Clamp your welding ground lead directly to your workpiece rather than the vise body to prevent electrical arcing across the lead screw threads.

FAQ for welders

Can the Yost LV-4 hold round pipe or tubing?

Yes. The Yost LV-4 features built-in pipe jaws cast directly beneath the main serrated clamping jaws. The maker lists a pipe capacity of 0.6 inches minimum diameter to 1.85 inches maximum diameter, which accommodates common small round tubing and conduit on the bench.

Does the Yost LV-4 include mounting bolts?

No. The listing explicitly states that mounting hardware is not included in the package. Because the listing does not publish bolt diameter or hole center spacing, measure the base lugs after unboxing before buying mounting hardware for your workbench.

How far does the Yost LV-4 swivel base rotate?

The vise head rotates 240 degrees on its swivel base. A swivel base lock tightens the base into position, allowing you to angle long pieces of bar stock or tubing away from bench walls and obstacles during grinding or fit-up.

What is the jaw opening and throat depth on the Yost LV-4?

The listing states a 4.5-inch jaw width and a 3-inch jaw opening. Throat depth has contradictory numbers on the listing, given as 2.6 inches in the bullet points and 2.375 inches in the specification table.

Related: best welding vise for table, best welding table for home shop, how to bevel metal for welding, and the welding tables and carts hub.

More buying guides