Sandblasting vs Bead Blasting: Which One Should You Buy?
Sandblasting strips with abrasive media and a pressure washer kit, while bead blasting cleans and finishes with glass beads in a cabinet or gun; here is how the four listings compare.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Selkie Pressure Washer Sandblasting Kits9.6/10View on Amazon - 2
12" x 24" Sandblasting Cabinet Tempered Glass Lens9.5/10View on Amazon - 3
#10 Glass Beads - 8 lb or 3.6 kg9.4/10View on Amazon - 4
#13 Glass Beads - 8 lb or 3.6 kg9.4/10View on Amazon
Verdict. Pick sandblasting when the job is stripping rust, paint and scale with a pressure washer kit, and pick bead blasting when the job is cleaning and finishing parts with glass bead media in a cabinet or gun. The Selkie kit and the Tellegloww lens sit on the sandblasting side, and the two INTERACTIVIA glass bead bags sit on the bead blasting side.
A rusted gate hinge, a painted trailer panel and a scaled engine bracket all need the old surface off before new paint or a weld goes on. That is the job behind sandblasting vs bead blasting: two ways to clean metal with a stream of media, one built for stripping and one built for finishing. This comparison puts the four listings side by side on what each one states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The two sides

Selkie Pressure Washer Sandblasting Kits
A wet abrasive sandblasting kit for a pressure washer, rated at 5000 PSI and 8 GPM, with a 10 ft hose, 16 inch wand, 17 inch sand wand, replacement ceramic nozzle kits and a goggle.
Pros
- Works with pressure washers rated 3000 PSI at 4 GPM or greater, up to 5000 PSI and 8 GPM
- Wet abrasive action; the maker says it makes no dust like a traditional sandblaster
- 10 ft hose with a 16 inch pressure washer wand and a 17 inch sand wand
- Two replacement ceramic nozzle kits and a goggle included
Cons
- Needs a pressure washer rated 3000 PSI at 4 GPM or greater; no washer is included
- Blasting media is a separate purchase; the kit includes no sand
- No warranty term is stated
- Wet blasting leaves the work wet, so the surface needs drying after the job

12" x 24" Sandblasting Cabinet Tempered Glass Lens
A 12 x 24 inch tempered glass cabinet lens with four 11 x 23 inch polyester film covers, the glass 3/16 inch thick and the film 5/64 inch thick.
Pros
- Tempered glass 3/16 inch thick with a replaceable film layer
- Four film covers included, so the window stays clear through long use
- Film is 5/64 inch thick, so the window seal is not compromised
- Double sided adhesive pre applied around the film for easy fitting
Cons
- Lens and film only; no cabinet, gun or media is included
- Fits cabinets with a 12 x 24 inch window; other sizes need a different lens
- No warranty term is stated
- The film is a wear item and needs replacing as it scratches

#10 Glass Beads - 8 lb or 3.6 kg
An 8 lb bag of #10 glass beads, extra fine at 100-170 mesh, for blast cabinets or sand blasting guns.
Pros
- 100-170 mesh, extra fine, for cleaning and finishing
- 8 lb bag, 3.6 kg, sized for cabinets or guns
- Spec No 10, a named grade, so reordering the same media is simple
- Small beads for cleaning and finishing work
Cons
- Media only; no cabinet, gun or nozzle is included
- An 8 lb bag suits small work; bigger jobs need more bags
- Made for cleaning and finishing, not for stripping heavy rust or thick paint
- No scoop or storage container is included

#13 Glass Beads - 8 lb or 3.6 kg
An 8 lb bag of #13 glass beads, fine at 220-240 mesh, for blast cabinets or sand blasting guns.
Pros
- 220-240 mesh, fine, for cleaning and finishing
- 8 lb bag, 3.6 kg, sized for cabinets or guns
- Spec No 13, a named grade, so reordering the same media is simple
- Small beads for cleaning and finishing work
Cons
- Media only; no cabinet, gun or nozzle is included
- An 8 lb bag suits small work; bigger jobs need more bags
- Made for cleaning and finishing, not for stripping heavy rust or thick paint
- No scoop or storage container is included
Other welders and gear to compare
Glass Bead Media for SandblastingCheck price on Amazon
#80 Grit Aluminum OxideCheck price on Amazon
Glass Beads Blasting Abrasive MediaCheck price on Amazon
Eastwood 50-Lb of Glass Beads Blasting Abrasive Media 140-230Check price on Amazon
15 LB Garnet 20/40 Mesh Sandblasting AbrasiveCheck price on Amazon
Side by side
| Selkie Pressure Washer Sandblasting Kit | Tellegloww 12 x 24 Sandblasting Cabinet Lens | INTERACTIVIA #10 Glass Beads | INTERACTIVIA #13 Glass Beads | |
|---|---|---|---|---|
| Gear Score | 60 | 53 | 51 | 50 |
| Side | Sandblasting | Sandblasting | Bead blasting | Bead blasting |
| Type | Wet abrasive kit for a pressure washer | Cabinet lens and film covers | Glass bead media | Glass bead media |
| Max pressure | 5000 PSI | Not stated | Not stated | Not stated |
| Mesh | 50-60 mesh sand recommended | Not stated | 100-170 mesh | 220-240 mesh |
| Size or weight | Not stated | 12 x 24 inch glass | 8 lb | 8 lb |
| Warranty | Not stated | Not stated | Not stated | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 20 November 2026. No listing here states a warranty term or a safety certification.
Sandblasting vs bead blasting: media and method
Sandblasting throws abrasive media at the surface to strip it. The Selkie kit is a wet abrasive setup for a pressure washer, and the maker recommends 50-60 mesh carborundum and garnet sand. The maker says the wet kit makes no dust like a traditional sandblaster.
Bead blasting throws glass beads at the surface to clean and finish it. The two bead listings are 8 lb bags of glass bead media for blast cabinets or sand blasting guns: #10 at 100-170 mesh, described as extra fine, and #13 at 220-240 mesh, described as fine. Both are sold as small beads for cleaning and finishing, not as stripping media. The grade names run the other way from the mesh: the #10 beads are sold as extra fine and the #13 beads as fine, but 220-240 mesh is finer than 100-170 mesh, so judge fineness by the mesh, not by the name.
The Tellegloww set belongs to the sandblasting side in a different way: it is the viewing window for a cabinet, one tempered glass lens with four film covers, so the operator can see the work while the media flies.
Pressure, flow and what comes with each listing
The Selkie kit is the only listing here with pressure and flow figures. The maker rates it at 5000 PSI and 8 GPM, with a minimum washer rating of 3000 PSI at 4 GPM or greater. The kit lists a 10 ft hose, a 16 inch pressure washer wand and a 17 inch sand wand, with a 1/4 inch NPT inlet and four hose clamps, plus a goggle and two extra replacement ceramic nozzle kits.
The Tellegloww set lists no pressure or flow figures, because it is a window, not a blaster. Its figures are size and thickness: a 12 x 24 inch glass lens at 3/16 inch thick, with four film covers at 11 x 23 inches and 5/64 inch thick. Double sided adhesive is pre applied around the film, and each pane ships protected.
The bead bags list weight, mesh and grade: each bag is 8 lb, or 3.6 kg. The #10 beads run 100-170 mesh and the #13 beads run 220-240 mesh. Neither bag lists a pressure, a flow or a nozzle size.
What each side is for
The sandblasting side is for removal. The Selkie maker lists rust, paint, stains and scale on machinery, engine compartments, driveways and barn doors. That is stripping work, and the wet setup keeps the dust down.
The bead blasting side is for cleaning and finishing. The bead listings describe small beads for cleaning and finishing in blast cabinets or sand blasting guns, which suits parts that need a clean surface without heavy material removal.
Choose sandblasting if
- You need rust, paint or scale off a part before paint or a weld.
- You already own a pressure washer rated 3000 PSI at 4 GPM or greater.
- You want the dust kept down with a wet abrasive setup.
- Your cabinet needs a new 12 x 24 inch window with spare films.
Choose bead blasting if
- You clean and finish parts rather than strip them bare.
- You already own a blast cabinet or a sand blasting gun.
- You want a fine glass bead, 100-170 mesh or 220-240 mesh, for finishing work.
- You buy media by the bag and keep a named grade, Spec No 10 or Spec No 13, on the shelf.
Before You Strike an Arc
Blasting throws media at speed, so set up for it before the first pass.
- Wear a supplied-air or rated respirator and eye protection, and never blast with silica sand: the OSHA silica rule covers it.
- Check the Selkie kit 1/4 inch inlet and hose clamps against your washer fittings before you start.
- Check the Tellegloww glass and film against your cabinet window, 12 x 24 inches for the glass and 11 x 23 inches for the film, before fitting.
- Match the media to the job: 50-60 mesh sand for the wet kit, 100-170 mesh #10 beads or 220-240 mesh #13 beads for finishing.
- Clamp the work down and keep the blast stream off skin and off anything you do not mean to strip.
FAQ for welders
What is the difference between sandblasting and bead blasting?
Sandblasting uses abrasive media to strip a surface, while bead blasting uses glass beads to clean and finish it. Here, the sandblasting side is the Selkie wet abrasive kit with 50-60 mesh carborundum and garnet sand, and the bead blasting side is the INTERACTIVIA glass beads at 100-170 mesh and 220-240 mesh. Pick the side that matches the job: stripping or finishing.
What media should I use for sandblasting?
Use the media the maker of your kit recommends. The Selkie kit recommends 50-60 mesh carborundum and garnet sand, and the glass bead listings are 100-170 mesh and 220-240 mesh media for blast cabinets or sand blasting guns. Match the mesh to the job and to the gun or cabinet you own.
Can you use regular sand for sandblasting?
No. Regular sand is silica sand, and the OSHA silica rule covers blasting with it, so use a rated blasting media instead. The listings here name 50-60 mesh carborundum and garnet sand for the wet kit and glass beads for cabinets and guns.
Is sandblasting safe?
Blasting throws media at speed, so wear a supplied-air or rated respirator and eye protection, and never blast with silica sand. The Selkie kit includes a goggle. Work with ventilation and keep the stream off skin.
Where can I buy sandblasting sand?
Blasting media is sold by the bag for cabinets and guns. Buy the grade and mesh your kit or cabinet calls for, such as 50-60 mesh carborundum and garnet sand for the Selkie kit, or Spec No 10 and Spec No 13 glass beads for finishing.
Related: best pressure washer sandblasting kit, best sandblasting media for aluminum, siphon vs pressure sandblaster, and the metal finishing hub. Also see the best sandblasting gun guide.
Scoring, line by line
Each pick is scored on performance, build, value, safety listing and warranty, using the same weights for every pick. The Selkie kit leads on stated capability, with the highest pressure and flow figures and the fullest box.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Selkie Pressure Washer Sandblasting Kit | 9.6 | 30 | 21 | 21 | n/a | 0 |
| Tellegloww 12 x 24 Sandblasting Cabinet Lens | 9.5 | 26 | 20 | 19 | n/a | 0 |
| INTERACTIVIA #10 Glass Beads | 9.4 | 24 | 19 | 19 | n/a | 0 |
| INTERACTIVIA #13 Glass Beads | 9.4 | 23 | 19 | 19 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.




