Siphon vs Pressure Sandblaster: Which One Should You Buy?
The LE LEMATEC and NANPU siphon kits state their air needs at 4 CFM at 90 PSI and 7 SCFM, while the pressure-side bundle pairs its gun kit with an oil water separator and a digital regulator.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
LE LEMATEC Sand Blaster Gun Kit for Air Compressor9.7/10View on Amazon - 2
NANPU Light-Duty Air Sandblaster Gun Kit9.6/10View on Amazon - 3
LE LEMATEC Premium Sand Blaster Gun Kit9.4/10View on Amazon
Verdict. Pick the siphon side when your compressor holds the stated air: the LE LEMATEC kit needs 4 CFM at 90 PSI and the NANPU needs 7 SCFM. Pick the pressure-side bundle only for its separator and digital regulator, since its listing states no CFM, PSI, nozzle or media figures for the gun.
Rust blooms on a trailer frame, paint lifts off a gate, and the bench holds a part that needs bare metal before paint. The question is siphon vs pressure sandblaster: a siphon gun pulls media up a hose with airflow, while a pressure blaster pushes media from a pressurized tank. The two siphon kits here state their air needs plainly, and the pressure-side bundle states a separator and a regulator but no air figures for the gun, so the choice turns on what your compressor can hold and what the listing actually states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The kits
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | LE LEMATEC Sand Blaster Gun Kit for Air Compressor | 9.7/10 | Buy on Amazon |
| 2 | NANPU Light-Duty Air Sandblaster Gun Kit | 9.6/10 | Buy on Amazon |
| 3 | LE LEMATEC Premium Sand Blaster Gun Kit | 9.4/10 | Buy on Amazon |

LE LEMATEC Sand Blaster Gun Kit for Air Compressor
A siphon and gravity feed gun kit that needs 4 CFM at 90 PSI, with a ceramic nozzle, a 7-foot siphon hose and a 46-220 grit media range.
Pros
- Needs 4 CFM at 90 PSI, with a 150 PSI maximum stated
- Gravity feed for detail work and siphon feed for larger flat surfaces
- Hardened ceramic nozzle, fully serviceable design
- 7-foot siphon hose included
Cons
- Not for pancake compressors under 6 gallons
- Siphon mode needs maximum airflow to generate vacuum lift
- Needs an inline filter and water trap, which are not in the box
- No warranty term is stated

NANPU Light-Duty Air Sandblaster Gun Kit
A siphon and gravity feed gun kit that runs at 90 to 150 PSI on 7 SCFM, with a ceramic nozzle and a stocked box of accessories.
Pros
- Runs at 90 to 150 PSI on 7 SCFM
- Siphon feed for heavy-duty work and gravity feed for detail work
- Ceramic nozzle with an alloy body
- Box holds gloves, goggles, 3 nozzles, 2 guards, a quick connector and 5 thread seal tape
Cons
- No warranty term is stated
- 6-foot hose is shorter than the LE LEMATEC 7-foot hose
- Heaviest here at 3.4 lb
- Siphon feed needs a compressor that can hold 7 SCFM

LE LEMATEC Premium Sand Blaster Gun Kit
A gun kit bundled with an oil water separator and a digital air pressure regulator, with gravity and siphon feed functions.
Pros
- Bundles a ZN312 oil water separator with a reusable one micron element
- DAR01B digital regulator gives an easy to read display
- Two control regulators for larger projects
- Gravity and siphon feed functions in one kit
Cons
- No air requirement is given, so compressor sizing is guesswork
- Needs a male-to-male adaptor that is not included
- No pressure-feed mode is described for a buyer who wants a pressure blaster
- The separator element needs cleaning and the drain valve needs pressing to eject moisture
Side by side
| LE LEMATEC AS118-2C | NANPU NP-ASBX2-G | LE LEMATEC Premium Bundle | |
|---|---|---|---|
| Gear Score | 61 | 60 | 50 |
| Side | Siphon | Siphon | Pressure |
| Feed | Gravity and siphon | Siphon and gravity | Gravity and siphon |
| Min air | 4 CFM at 90 PSI | 7 SCFM | Not stated |
| Max pressure | 150 PSI | 90 to 150 PSI | Not stated |
| Nozzle | Ceramic | Ceramic | Not stated |
| Media | Aluminum oxide, glass beads, silicon carbide, 46-220 grit | Aluminum oxide, sand, walnut shells, soda | Not stated |
| Hose | 7-foot siphon hose | 6-foot air hose and tube | Not stated |
| Weight | 2.18 lb | 3.4 lb | 2.0 lb |
| Warranty | Not stated | Not stated | Not stated |
| In the box | Gun, 7-foot siphon hose | Gun, 6-foot hose, gloves, goggles, 3 nozzles, 2 guards, quick connector, 5 thread seal tape | Gun kit, oil water separator, digital air pressure regulator |
Ratings in this table are the makers’ own claims taken from each product page (4 November 2026). No listing here states a CSA, UL or ETL listing or a warranty term.
Siphon vs pressure sandblaster: how the feed works
A siphon gun uses airflow to pull media up a hose and into the airstream, and the LE LEMATEC kit says siphon mode needs maximum airflow to generate vacuum lift. Both siphon kits here also offer gravity feed for smaller detail work: the LE LEMATEC kit calls gravity feed right for small, quick detail work, and the NANPU kit calls it right for smaller, detailed tasks. The LE LEMATEC Premium bundle adds a separator and a digital regulator to the gun kit, but its listing describes the gun kit with gravity and siphon feed functions and gives no pressure-feed figure, so the pressure side of this comparison rests on the bundle rather than on a stated pressure feed.
Air supply: CFM and PSI
The LE LEMATEC kit needs a minimum of 4 CFM at 90 PSI for continuous operation, with a maximum pressure of 150 PSI, and it warns that pancake compressors under 6 gallons will not do, and that small 1 to 3-gallon compressors will sputter with low performance. See our pancake vs vertical air compressor guide for the tank sizes. The NANPU kit runs at 90 to 150 PSI and consumes 7 SCFM. The pressure-side bundle states no CFM or PSI figure for the gun, so the two sides cannot be compared on air needs: the siphon listings state theirs, and the bundle leaves its air needs unclear.
Media, nozzles and hose
The LE LEMATEC kit takes clean, dry media between 46-220 grit, including aluminum oxide, glass beads and silicon carbide, and it uses a hardened ceramic nozzle with a 7-foot siphon hose. The NANPU kit takes aluminum oxide, sand, walnut shells and soda, and it uses a ceramic nozzle with a 6-foot air hose and tube. See our blasting media types and sandblasting nozzle types guides. The bundle states no media, nozzle or hose figures, so media choice and nozzle wear cannot be compared across the sides. The LE LEMATEC kit warns that wet air clumps media and says to use an inline filter and water trap to keep air dry.
What is in the box
The NANPU box holds a gun kit, a 6-foot hose and tube, gloves, goggles, 3 ceramic nozzles, 2 nozzle guards, a quick connector and 5 pieces of thread seal tape. The LE LEMATEC kit includes the gun and a 7-foot siphon hose. The bundle includes the gun kit, the ZN312 oil water separator and the DAR01B digital regulator, but connecting the 3 parts needs a male-to-male adaptor that is not included. See our best air regulator and filter for air compressor guide for the separator and regulator.
Choose the siphon side if
- Your compressor holds 4 CFM at 90 PSI or 7 SCFM, as the two kits state.
- You want gravity feed for detail work and siphon feed for larger flat surfaces.
- You want a stated grit range and a ceramic nozzle.
- You want spare nozzles, gloves and goggles in the box.
Choose the pressure side if
- You want an oil water separator and a digital regulator in the same bundle.
- You want the gun kit, separator and regulator from one maker.
- You already have a male-to-male adaptor for the connections.
- You value the separator and regulator more than stated air figures.
FAQ for welders
What air supply does a siphon sandblaster need?
The LE LEMATEC kit needs a minimum of 4 CFM at 90 PSI, and the NANPU kit runs at 90 to 150 PSI on 7 SCFM. Pancake compressors under 6 gallons will not run the LE LEMATEC kit, and small 1 to 3-gallon compressors will sputter. The pressure-side bundle states no air figure.
Does a siphon sandblaster work for glass etching?
Yes. The LE LEMATEC kit is made for glass etching as well as rust removal and surface preparation, and the NANPU kit etches intricate designs on glass. Use clean, dry media in the stated grit range for the LE LEMATEC kit.
What media works in these sandblasters?
The LE LEMATEC kit takes aluminum oxide, glass beads and silicon carbide between 46-220 grit, and the NANPU kit takes aluminum oxide, sand, walnut shells and soda. For the LE LEMATEC kit, use only clean, dry media, and fit an inline filter and water trap to keep air dry.
Does the pressure-side bundle include a regulator?
Yes. The bundle includes the DAR01B digital air pressure regulator with an easy to read display, and the ZN312 oil water separator with a reusable one micron element. Connecting the 3 parts needs a male-to-male adaptor that is not included.
Is a water trap needed for sandblasting?
Yes, for the LE LEMATEC kit: wet air clumps media, so the maker says to use an inline air line filter and water trap to keep air dry. The bundle includes an oil water separator that filters moisture out of the air line.
Related: soda blaster vs sandblaster, sandblasting vs wire wheel for rust removal, blasting media types and the sandblasting hub.
Scoring, line by line
All 3 kits are scored on performance, build, value, safety listing and warranty. No listing here states a safety certification or a warranty term, so safety and warranty score zero across the board.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| LE LEMATEC AS118-2C | 9.7 | 30 | 22 | 21 | n/a | 0 |
| NANPU NP-ASBX2-G | 9.6 | 29 | 21 | 22 | n/a | 0 |
| LE LEMATEC Premium Bundle | 9.4 | 23 | 19 | 19 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.
Before you strike an arc. Wear a supplied-air or rated respirator for sandblasting and use no silica sand, and keep the media clean and dry with an inline filter and water trap. Clamp the work, wear eye protection, and check the hose and fittings before each session. See the OSHA silica rule.




