Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Powder Coating DIY Kit: How to Set Up at Home

What a powder coating diy kit needs at home: the gun, powder, booth and oven, and the steps from bare metal to a cured finish.

Powder Coating DIY Kit: How to Set Up at Home
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Eastwood HotCoat PCS-250 Powder Coating Gun Plus BenchtopEastwood HotCoat PCS-250 Powder Coating Gun Plus Benchtop9.6/10View on Amazon
  2. 2VEVOR Powder Coating SystemVEVOR Powder Coating System9.6/10View on Amazon
  3. 3Yalikop 186Pcs Powder Coating Plugs and Tape Assortment KitYalikop 186Pcs Powder Coating Plugs and Tape Assortment Kit9.6/10View on Amazon

A bare metal bracket on the bench, fresh off the grinder, needs a finish that will not chip the first time a wrench slips. A powder coating diy kit is the home shop version of that finish: a powder gun with a power source and ground clamp, dry powder in a bottle or pouch, a booth or fan setup to catch overspray, and an oven to bake the coated part. Spray the powder onto grounded bare metal, then bake it until it melts, levels and hardens into a film.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What a powder coating diy kit includes

A home kit is built around the gun. Eastwood lists its PCS-150 as a single voltage powder coating gun with power source, ground clamp and cable, and an empty 8-oz. clear bottle, with instructions. The same maker lists the PCS-250 with a low 15,000-Volt setting and a high 25,000-Volt setting for multi-coat coverage over larger areas. Powder itself comes in bottles or pouches: Eastwood lists 8 Ounce bottles of red, white and gloss black powders with one PCS-150 kit, and ninesung lists 7 Colors at about 4 oz per color in resealable pouches. A booth and an oven complete the setup, and neither is part of the gun package Eastwood lists for the PCS-150.

The setup, part by part

Setup part What it does Stated example Figure from listings
Powder gun Charges powder and sprays it onto grounded metal Eastwood PCS-150 15,000-volt setting, 120v / 60Hz
Dual-voltage gun Low and high settings for coverage Eastwood PCS-250 15,000-Volt low, 25,000-Volt high
Booth Captures overspray around the part Eastwood BenchTop booth kit Over 99% of overspray, 20-inch box fan
Powder Dry coating material in bottles or pouches ninesung 7 Colors About 4 oz per color
Large system Tank-fed electrostatic system Generic WX-958S 45L powder tank, 90-260V

Figures above are the makers’ stated figures for the named models. Follow the powder maker’s bake schedule and the gun manual for your own parts, since bake needs vary by powder.

How the process works, step by step

Prep the metal

Powder sticks to clean bare metal, not to oil, rust or old paint. Strip the part to bare metal, degrease it, and keep bare hands off the cleaned surface. Mask threads and faces that must stay bare, and hang the part from a hook or rod so you can reach every side without touching it. Our how to prep for powder coating guide covers the prep work in detail.

Ground the part and spray the powder

Clip the ground clamp to the part or its hanger so the metal is grounded. The gun charges the powder as it leaves the nozzle, and the grounded part draws the powder in and holds it in place. Eastwood lists the PCS-150 at a 15,000-volt setting on standard 120v / 60Hz household current, with color-coded cables for setup and a clear bottle so you can see powder color and level. Spray in light passes and turn the part as you go. The finish at this stage is a dull powder layer, not the final coat.

Catch the overspray

Powder that misses the part hangs in the air and settles on everything nearby, so a booth earns its bench space. Eastwood lists its BenchTop booth kit as capturing over 99% of powder overspray, built around a standard 20-inch box fan that is not included, with rods for hanging parts and a 20x20x1 powder booth filter. The PCS-250 booth kit from the same maker is listed as capturing over 95% of powder overspray and using a standard 20 Inch box fan. Work inside the booth opening and keep the fan running while you spray.

Bake in an oven

Move the coated part, still on its hanger, into the oven without touching the powder. Heat melts the powder so it flows out, levels and then hardens into a continuous film as it bakes and cools. Use the temperature and time on your powder’s own instructions, since those figures come from the powder maker and differ by powder. Use an oven dedicated to shop work, never the oven you cook food in, and let the part cool before handling. Our how does powder coating work page explains the bake in more detail.

Gun choices in the reference listings

Home guns in these listings split by voltage control. The Eastwood PCS-150 is a single voltage gun at a 15,000-volt setting, listed at 4.4 pounds for the system with an empty 8-oz. clear bottle, and a 1-year limited warranty. The Eastwood PCS-250 adds a high 25,000-Volt setting alongside the low 15,000-Volt setting, which the maker lists for multi-coat coverage over larger areas. At the larger end, the Generic WX-958S (on Amazon) lists a 45L stainless steel powder tank, 90-260V power compatibility and knobs for powder, air, rinsing air, kV and uA. That is a tank-fed system, a different class from a handheld bottle gun. See our best powder coating gun for home use guide for the gun roundup.

Powder, booth and oven notes

  • Powder storage. ninesung lists its 7 Colors in resealable aluminum foil pouches at about 4 oz per color, made to preserve quality and reduce waste. Keep powder dry and sealed between jobs.
  • Booth size. Eastwood lists the BenchTop booth frame at 18 gauge steel with rods for hanging parts, made to coat multiple items at once in a garage or small shop.
  • Part size limit. Your oven sets the real limit. A part that does not fit in the oven with clearance around it cannot be baked at home, no matter what the gun can spray.
  • Color changes. A clear bottle, like the 8-oz. bottle Eastwood lists with the PCS-150, lets you see powder color and level before you spray, which helps when you swap colors.

Shop safety. Powder is a fine dust: wear a respirator rated for dust, eye protection and gloves while spraying, and keep the booth fan pulling air away from you. Keep powder and the oven away from open flame and grinding sparks, and let baked parts cool before handling. Follow the gun and powder makers’ instructions for grounding and cleanup, and see our Safety Disclaimer.

FAQ for welders

What do I need besides the gun?

Powder, a booth or fan setup to catch overspray, hooks or rods to hang parts, and an oven dedicated to shop work for curing. Eastwood lists the PCS-150 package as the gun with power source, ground clamp and cable, an empty 8-oz. clear bottle and instructions.

Can I powder coat in a garage?

Yes, that is the use these kits are sold for. Eastwood lists its booth kits as made for powder coating in a garage or small shop, built around a standard 20-inch box fan. The BenchTop booth kit adds a 20x20x1 powder booth filter to capture overspray.

What metals can I powder coat?

Powder coating is used on steel and other metallic products, and the ninesung powder (on Amazon) listing names metal, steel, iron and aluminum surfaces. The part must be bare, clean metal that can take oven heat for the bake.

How much powder comes in a kit?

It depends on the kit. Eastwood lists one PCS-150 kit with 8 Ounce bottles of red, white and gloss black powders, and ninesung lists 7 Colors at about 4 oz per color in resealable pouches.

Do I need a special oven?

You need an oven that fits your parts and holds the bake temperature your powder maker specifies. Keep it as a shop-only oven, separate from food cooking, and follow the powder instructions for time and temperature.

Related: how to powder coating at home, how to prep for powder coating, best powder coating gun for home use, and the metal fab tools hub.

More buying guides