Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Prep for Powder Coating: Step-by-Step

How to prep for powder coating starts with a clean, dry, masked part hung so powder can reach every surface.

How to Prep for Powder Coating: Step-by-Step
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Yalikop 186Pcs Powder Coating Plugs and TapeYalikop 186Pcs Powder Coating Plugs and Tape9.6/10View on Amazon
  2. 2Swpeet 104Pcs 36 Yards 4 Sizes 1/4",1/2", 7/10"Swpeet 104Pcs 36 Yards 4 Sizes 1/4",1/2", 7/10"9.5/10View on Amazon
  3. 3125PCS Powder Coating Hook Kit125PCS Powder Coating Hook Kit9.5/10View on Amazon

A part comes back from the oven with powder peeling off in sheets, and the fault was set before the gun ever fired. How to prep for powder coating is the answer: clean the metal, strip loose rust and old coat, dry the part, mask the areas that must stay bare, and hang it so powder can reach every surface. Prep is where a durable coat is made, and a part that is dirty, oily or damp will shed powder no matter how good the gun is.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Yalikop 186Pcs Powder Coating Plugs and Tape

Yalikop 186Pcs Powder Coating Plugs and Tape

Yalikop9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 186-piece masking kit with plugs, caps, hooks and tape for holes from 1/16 inch to 3/4 inch, rated to 600°F for 20+ minutes.

Pros

  • 80 rubber plugs in 8 sizes, 10pc each
  • 80 silicone caps in 8 sizes, 10pc each
  • 25 C hooks and 1 roll of high temp tape in the box
  • Heat resistance up to 600°F/315°C for 20+ minutes

Cons

  • No warranty term is stated
  • Tape is 0.39 x 12.99 inches, a short roll for large parts
  • C-hooks measure 4.02 x 1.1 inches, so large parts need a larger hook
  • Plugs and caps cover only the stated size ranges
Swpeet 104Pcs 36 Yards 4 Sizes 1/4",1/2", 7/10"

Swpeet 104Pcs 36 Yards 4 Sizes 1/4",1/2", 7/10"

Swpeet9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 104-piece kit with 36 yards of masking tape in 4 sizes and silicone plugs for holes from 1/16 inch to 3/4 inch.

Pros

  • 4 rolls of tape, 36 yards, in 1/4, 1/2, 7/10 and 1 inch sizes
  • 8 sizes of silicone plugs for holes from 1/16 inch to 3/4 inch
  • Tape rated to 428°F (220°C)
  • Color coded plugs, so the right size is easy to grab

Cons

  • No warranty term is stated
  • Heat rating of 428°F is lower than the 600°F rating on the Yalikop kit
  • No hooks in the box, so hanging needs a separate hook
  • Tape sizes stop at 1 inch, so wide areas need overlapping strips
125PCS Powder Coating Hook Kit

125PCS Powder Coating Hook Kit

Mitoltpoci9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 125-piece set of steel hooks in 4-inch, 5-inch, 6-inch and 7-inch sizes, with wire diameter of .120 inch / 3mm and hooks that hold up to 30 lbs.

Pros

  • 125 hooks in 4 sizes: 4-inch, 5-inch, 6-inch and 7-inch
  • Wire diameter of .120 inch / 3mm in 65MN spring steel
  • Hooks hold up to 30 lbs
  • Hooks snap into place with no tools or assembly

Cons

  • Hooks only, no tape, plugs or caps in the box
  • Hooks hold up to 30 lbs, so a heavier part needs a stronger hook
  • A hook leaves a bare spot where it grips the part
  • Hooks fit standard bracket systems, so a part with no hole or edge to hang from needs another setup

How to prep for powder coating, step by step

Prep follows a plain order, and each step sets up the next. Clean and strip the part, dry it, mask threads, holes and mating surfaces, hang it on a hook that holds its weight, and check the ground path before spraying. The gear in this guide handles the hanging and masking steps: hooks hold the part, tape covers flat areas, and plugs and caps cover holes and studs.

  • Clean. Remove oil, grease and shop dirt from the metal, then wipe the part dry.
  • Strip. Remove loose rust, scale and flaking coat so powder bonds to sound metal.
  • Dry. Let the part dry fully, since damp metal sheds powder.
  • Mask. Cover threads, holes and mating faces with tape, plugs or caps.
  • Hang. Hang the part on a hook that fits its weight and leaves the coated faces open.
  • Check. Check that the hook, the rack and the ground lead all make clean metal contact.

Side by side

Product Kit contents Sizes covered Heat resistance Item weight
Yalikop 186-Piece Masking Kit 80 plugs, 80 caps, 25 C hooks, 1 roll of tape Plugs 1/16 to 3/4 inch; caps to 3/4 inch Up to 600°F/315°C for 20+ minutes Not stated
Swpeet 104-Piece Masking Kit 4 rolls of tape, silicone plugs Tape 1/4, 1/2, 7/10 and 1 inch; plugs 1/16 to 3/4 inch Up to 428°F (220°C) 0.01 pounds
Mitoltpoci 125-Piece Hook Kit 125 steel hooks in 4 sizes 4-inch, 5-inch, 6-inch and 7-inch hooks Not stated 1.0 pounds

The table above compares the kits in this guide. The sections below explain each prep step in more detail, with the figures that maker listings state.

Clean, strip and dry

Powder bonds to clean metal, not to oil or loose rust. Wash the part, then strip rust and scale with a wire wheel, abrasive pad or blaster until the surface is sound. The sandblasting vs wire wheel for rust removal guide compares sandblasting with a wire wheel for stripping a part, and the best wire brush for rust removal guide covers brushes for the job. After stripping, wipe the part and let it dry fully before masking, since a damp part traps moisture under the coat. Wear gloves after cleaning, so skin oil does not land back on the metal.

Mask what stays bare

Threads, holes, bearing seats and mating faces must stay bare, or the part will not fit together after baking. High temp tape covers flat areas and edges, silicone plugs fill holes, and silicone caps cover studs and bolts. The Swpeet kit (on Amazon) in this guide states tape in 1/4, 1/2, 7/10 and 1 inch sizes with heat resistance up to 428°F (220°C), and plugs in 8 sizes for holes from 1/16 inch to 3/4 inch. The Yalikop kit (on Amazon) states plugs for holes from 1/16 inch to 3/4 inch, caps for diameters up to 3/4 inch, and heat resistance up to 600°F/315°C for 20+ minutes. Press tape down flat at the edges, and seat each plug or cap fully, so powder does not creep under a loose edge.

Hang the part and check the ground

A part that lies on a bench gets no powder on the face that touches the bench, so hang it. Pick a hook that fits the part weight and the hole or edge it hangs from: the Mitoltpoci kit (on Amazon) in this guide states hooks in 4-inch, 5-inch, 6-inch and 7-inch sizes, with wire diameter of .120 inch / 3mm in 65MN spring steel, and hooks that hold up to 30 lbs. Hang the part so the faces that matter face the gun, and keep the hook contact on a spot that can stay bare. Check the ground path from the rack to the part, since powder needs grounded metal to attract it. For the gun itself, see the powder coating gun for beginners guide, and for the full home setup, see how to powder coating at home.

Gear for hanging and masking

The kits below handle the hanging and masking steps in the prep order above: hooks hang the part, and tape, plugs and caps mask the areas that must stay bare.

FAQ for welders

Can powder coating go over rust?

No, powder needs sound metal to bond to. Strip loose rust and scale, then clean and dry the part. A coat over loose rust peels with the rust under it.

What should be masked before powder coating?

Mask threads, holes, bearing seats and mating faces that must stay bare for the part to fit. Use high temp tape on flat areas, plugs in holes, and caps on studs and bolts.

How hot can masking tape and plugs get in the oven?

Check the rating on the kit in hand. The Swpeet kit states tape rated up to 428°F (220°C), and the Yalikop kit states heat resistance up to 600°F/315°C for 20+ minutes. A kit rated below the bake setting risks melting or leaving residue.

Can a part be powder coated while it lies on a bench?

No, the face on the bench gets no powder. Hang the part on a hook so powder can reach every face, and keep the hook on a spot that can stay bare.

Why does powder fall off a part before baking?

A weak ground can cause it. The hook and the rack must make clean metal contact with the part, and the ground lead must be intact. Clean the contact points and hang the part again.

What hook size does a part need?

Match the hook to the part weight and to the hole or edge it hangs from. The Mitoltpoci kit states hooks in 4-inch, 5-inch, 6-inch and 7-inch sizes, with hooks that hold up to 30 lbs. A hook loaded past 30 lbs can bend, and a hook that is too large will not fit the hole.

Related: powder coating oven parts, how to remove powder coating from metal, how hot does a powder coating oven need to be, and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

Powder Coating Gun Parts Explained

Powder coating gun parts work as a set, with the gun, powder supply, nozzle, ground lead, control unit and air supply each shaping how…