Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Plasma Cutter Roller Guide: How to Use One

A plasma cutter roller guide holds the torch off the plate at a set height so long cuts stay straight, and this guide covers how it works, which torch types take PT-31 and AG-60 guides, and how the guides here differ in fit and adjustment.

Plasma Cutter Roller Guide: How to Use One
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1PT-31 Circle Guide LG40 Circinus Roller GuidePT-31 Circle Guide LG40 Circinus Roller Guide9.6/10View on Amazon
  2. 2PT-31 Roller Guide Stand-Off Spacer for CUT40PT-31 Roller Guide Stand-Off Spacer for CUT409.6/10View on Amazon
  3. 3Plasma Cutter Roller Guide Wheel for AG60 SG-55Plasma Cutter Roller Guide Wheel for AG60 SG-559.6/10View on Amazon
  4. 4AG-60 SG-55 Plasma Cutter Roller Guide WheelAG-60 SG-55 Plasma Cutter Roller Guide Wheel9.5/10View on Amazon

A long straight cut starts before the arc does: the torch has to stay at one height and travel in one line while the plate stays put. A plasma cutter roller guide is the small wheeled spacer that clips to the torch and rolls along the plate, holding the tip off the metal at a set height so the cut stays straight and the tip does not drag. This guide explains how it works, which torch types take which guide, and how the guides below differ.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

PT-31 Circle Guide LG40 Circinus Roller Guide

PT-31 Circle Guide LG40 Circinus Roller Guide

BDR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A PT-31 roller guide with a stated height range of 1.57 in to 1.81 in and positioning screws, for CUT-40, CUT-50, CUT-50D and LGK-40 machines.

Pros

  • Height range stated at both ends, 1.57 in / 40 mm to 1.81 in / 46 mm
  • Positioning screws adjust and fix the guide to different PT-31 torch types
  • Fits PT-31 and LG-40 torches on CUT-40, CUT-50, CUT-50D and LGK-40 machines
  • Dimensions stated: 2.0 x 2.0 x 0.7 inches

Cons

  • Aftermarket part, not an original part
  • No warranty term is stated
  • Fits PT-31 and LG-40 torches only, not AG-60 torches
  • No shield cup size is stated
PT-31 Roller Guide Stand-Off Spacer for CUT40

PT-31 Roller Guide Stand-Off Spacer for CUT40

WeldingStop9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A double-wheel PT-31 roller guide with positioning screws and height adjustment up to 1.81 in for CUT-40, CUT-50, CUT-50D and LGK-40 machines.

Pros

  • Double wheel design, listed for balance during cutting
  • Positioning screws adjust and fix the guide to different PT-31 torch types
  • Wheels adjust in height up to 1.81 in / 46 mm
  • Free after-sales consulting from the maker

Cons

  • Aftermarket part, not an original part
  • No warranty term is stated
  • Fits PT-31 and LG-40 torches only, not AG-60 torches
  • No dimensions are stated
Plasma Cutter Roller Guide Wheel for AG60 SG-55

Plasma Cutter Roller Guide Wheel for AG60 SG-55

TimelyDu9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An AG-60 roller guide for grooved shield cups with a 1.1 inch inner diameter and pilot arc starting for non-contact cuts.

Pros

  • Fits SG-55, AG-60 and WSD-60 torches
  • Made for shield cups with a groove, 1.1 in / 27 mm inner diameter
  • Works with pilot arc starting for smooth, non-contact cuts
  • Wheels adjust up to 1.78 in / 45 mm

Cons

  • Fits grooved shield cups only, not cups without a groove
  • Height tops out at 1.78 in, under the 1.81 in PT-31 guides
  • Fits AG-60 torch types only, not PT-31 torches
  • No dimensions are stated
AG-60 SG-55 Plasma Cutter Roller Guide Wheel

AG-60 SG-55 Plasma Cutter Roller Guide Wheel

HKBLUESWELD9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An AG-60 roller guide wheel spacer for shield cups without a groove, at 27 mm inner diameter, with pilot arc starting for SG-55, AG-60 and WSD-60 torches.

Pros

  • Fits SG-55, AG-60 and WSD-60 torches
  • Made for shield cups without a groove, 27 mm inner diameter
  • Works with pilot arc starting
  • Wheel spacer design holds the torch off the plate while cutting

Cons

  • No height adjustment figure is stated
  • Fits AG-60 torch types only, not PT-31 torches
  • Made for shield cups without a groove, so check the cup before ordering
  • One guide in the pack, no spare

What a plasma cutter roller guide does

The guide clips to the torch and its wheels ride on the plate, so the tip holds a steady stand-off instead of resting on the metal. That steady height matters most on long cuts, where a hand-held torch drifts, and on circle cuts, where a circle guide keeps the torch moving around a center point.

Side by side

Guide Torch fit Height adjustment Shield cup Pilot arc starting
BDR PT-31 Roller Guide PT-31 / LG-40 1.57 in / 40 mm to 1.81 in / 46 mm Not stated Not stated
WeldingStop PT-31 Roller Guide PT-31 / LG-40 Up to 1.81 in / 46 mm Not stated Not stated
TimelyDu AG60 Roller Guide SG-55 / AG-60 / WSD-60 Up to 1.78 in / 45 mm Grooved cup, 1.1 in / 27 mm Yes, non-contact cuts
HKBLUESWELD AG-60 Roller Guide SG-55 / AG-60 / WSD-60 Not stated Cup without a groove, 27 mm Yes, pilot arc starting

Fit decides the pick: PT-31 guides fit PT-31 and LG-40 torches, while AG-60 guides fit SG-55, AG-60 and WSD-60 torches. Check the torch model and the shield cup before ordering.

Which guide fits a PT-31 torch

Two guides here fit PT-31 and LG-40 torches: the WeldingStop guide and the BDR guide, both listed for CUT-40, CUT-50, CUT-50D and LGK-40 machines. Both use positioning screws to adjust and fix the guide to different PT-31 torch types, and both adjust in height up to 1.81 in / 46 mm. The BDR guide states the full range from 1.57 in / 40 mm.

Which guide fits an AG-60 torch

Two guides here fit SG-55, AG-60 and WSD-60 torches: the TimelyDu guide and the HKBLUESWELD guide (on Amazon). Both work with pilot arc starting; the TimelyDu guide states this gives smooth, non-contact cuts. The difference is the shield cup: the TimelyDu guide is made for shroud shield cups with a groove, 1.1 inch / 27 mm inner diameter, while the HKBLUESWELD guide works with the shroud shield cup without a groove.

How to use a plasma cutter roller guide

Mount the guide on the torch and lock it in place, the PT-31 guides lock with positioning screws, then, on a guide with height adjustment, set the wheel height for the stand-off the cut needs. Roll the wheels along the plate and let the guide carry the torch, so the tip stays off the metal through the whole cut. With pilot arc starting, the arc starts without the tip touching the plate, which suits non-contact cuts.

Roller guides for PT-31 and AG-60 torches

Each guide below handles one part of the job: fitting the torch, setting the stand-off height, or rolling a straight line.

For more options, see our plasma cutters guides.

FAQ for welders

Does a plasma cutter roller guide fit any plasma torch?

No. Fit follows the torch model: the PT-31 guides here fit PT-31 and LG-40 torches on CUT-40, CUT-50, CUT-50D and LGK-40 machines, while the AG-60 guides fit SG-55, AG-60 and WSD-60 torches. Check the torch model on the cutter before ordering.

How do I set the height on a roller guide?

Use the positioning screws on the PT-31 guides to set the wheel height, then lock the guide in place. The WeldingStop and BDR guides adjust up to 1.81 in / 46 mm, and the BDR guide states the full range from 1.57 in / 40 mm.

What is the difference between the two AG-60 guides?

The shield cup. The TimelyDu guide is made for shroud shield cups with a groove, at 1.1 inch / 27 mm inner diameter, while the HKBLUESWELD guide works with the shroud shield cup without a groove. Both work with pilot arc starting.

Are these roller guides original parts?

The WeldingStop and BDR guides state they are aftermarket parts, not original parts. The maker of the WeldingStop guide offers free after-sales consulting, and the TimelyDu guide offers free after-sales support.

Related: best plasma cutter, best outdoor plasma cutter, and how to use a CNC plasma table.

More buying guides