Countersink Bit Sizes: Chart and Guide
Countersink bit sizes run two ways: screw-size sets from #4 to #12 and diameter sets from 1/4 to 3/4 inch, all at an 82-degree angle.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
5PC Countersink Bits for Steel9.7/10View on Amazon - 2
Countersink Drill Bit Set9.6/10View on Amazon - 3
5 Pcs Countersink Drill Bit Set9.5/10View on Amazon
A flat-head screw driven straight into wood sits proud of the surface, catching fingers and looking unfinished. A countersink bit cuts the cone-shaped seat the screw head drops into, so the head sits flush. This guide explains countersink bit sizes: the screw-size sets, the diameter sets, the angle they share, and how to match a bit to the screw in hand.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Countersink bit sizes: the short answer
Countersink bit sizes come in two systems. Screw-size sets are marked by the screw they fit, and diameter sets are marked by the width of the bit. The screw-size sets in the listings run from the smallest to the largest screw size they cover, and the diameter sets run across a spread of bit widths. Every listing here states the same countersink angle, and most sets share the same shank size, so the choice comes down to matching the bit to the screw and to the material.
Side by side
| Screw or bit | Straight sets | Tapered sets | Diameter sets | Notes |
|---|---|---|---|---|
| #4 screw | 5/64 in pilot | 7/64 in pilot | Not a screw size | Smallest screw size in the sets |
| #6 screw | 3/32 in pilot | 9/64 in pilot | Not a screw size | Pilot size differs by set type |
| #8 screw | 7/64 in pilot | 11/64 in pilot | Not a screw size | Pilot size differs by set type |
| #10 screw | 1/8 in pilot | 3/16 in pilot | Not a screw size | Check the set type before drilling |
| #12 screw | 9/64 in pilot | 7/32 in pilot | Not a screw size | Largest screw size in the sets |
| Countersink angle | 82 degrees | 82 degrees | 82 degrees | Same angle in every listing |
| Shank | 1/4 in hex | 1/4 in hex | 1/4 in shank | Fits hand, bench and electric drills |
| Plug cutters | 3/8 and 1/2 in | 3/8 and 1/2 in | Not stated | Cut plugs to cover the screw head |
Read the table by set type first. Straight sets and tapered sets give different pilot sizes for the same screw, so a pilot size is only right for the set type that states it. Diameter sets use a different system entirely: the size is the width of the bit, not the screw it fits.
Screw-size sets: #4 to #12
Screw-size sets mark each bit by the screw it fits, and the listings here cover screws from the smallest to the largest size in the sets. EZARC straight sets list the pilot sizes for screws from #4 through #12, with the pilot growing as the screw grows. The tapered sets in the chart, from EZARC and FTG, list the same screw sizes with wider pilots, because a tapered bit cuts a wider hole at the top than a straight bit. Check the chart that comes with the set: a pilot size from a straight set does not fit a tapered set, and the other way round.
Diameter sets: 1/4 to 3/4 inch
Diameter sets skip the screw size and mark each bit by its width. The DEWALT set lists bits across a spread of diameters, and the msljtaim set lists the same spread, both with the same precise angle for wood, plastic and soft metal. Pick the diameter by the head of the screw: the cone the bit cuts must be wide enough for the head to sit flush, and narrow enough to leave wood around it. A diameter set suits a shop that already knows the screw head it drills for, rather than a shop matching bits to screw sizes.
The 82-degree angle
Every listing here states the same countersink angle. That angle matches the flat-head screws the sets are made for, so the head seats flat against the cone the bit cuts. The WildBossy listing states the same angle for screws made to the imperial standard, and the EZARC, DEWALT, FTG, Seuphubs and msljtaim listings all state it too. If a bit states a different angle, its cone will not match the screw head, and the head will sit proud or rock in the seat.
Wood, plastic and metal: what each set states
Most sets here are made for wood. The EZARC sets state softwood and hardwood, with a note against extended use on hardwood, and the FTG and Seuphubs sets state woodworking and furniture work. The WildBossy set states natural wood, engineered wood, MDF, particle boards, plywood, aluminum, non-ferrous metals and decorative materials. The DEWALT set states metal, wood, soft metals, plastic, PVC and fiberglass, but not stainless steel, and the msljtaim set states wood, plastic and soft metal, and not stainless steel or iron plates. Match the set to the material its listing states.
Depth stops, plug cutters and shanks
Several sets add depth stop rings that set how deep the bit cuts, so each hole comes out the same. The Seuphubs set states a drilling depth and a countersink depth, and its ball bearing collar stops the cut when it touches the wood. Plug cutters in the EZARC sets cut wood plugs to cover the screw head, in the sizes their listings state. Most sets here use a 1/4-inch hex shank that fits hand drills, bench drills and electric drills. The DEWALT set states a 1/4-inch shank, and some sets add a magnetic extension holder for extra reach. The WildBossy listing adds a usage tip of its own: operate the countersinks at a slow speed, which keeps the edges clean.
What size countersink bit for a #10 screw
A #10 screw takes a different pilot in each set type. In the straight sets the pilot for a #10 screw is the size the EZARC listings state, and in the tapered sets in the chart it is the wider size the EZARC and FTG listings state. Read the chart on the set you hold: the screw size alone does not fix the pilot, the set type does. When the pilot matches, the screw drives straight and the head seats flush in the cone.
FAQ for welders
What size countersink bit do I need for a #10 screw?
It depends on the set type. The straight sets list one pilot size for a #10 screw and the tapered sets list a wider one, so check the chart on the set you hold. The table above shows both sizes side by side.
What is the standard countersink angle?
The listings here all state the same angle, and it matches the flat-head screws these sets are made for. A bit with a different angle will not seat the head flat, so check the angle before buying.
Do countersink bits work on metal?
Some do. The DEWALT set states use on metal, wood, soft metals, plastic, PVC and fiberglass, and the msljtaim set states wood, plastic and soft metal. The EZARC wood sets state softwood and hardwood, and extended use on hardwood is not recommended.
What are plug cutters for?
Plug cutters cut short wood plugs from a board, and the plug covers the screw head after the screw is driven home. The EZARC sets include plug cutters in the sizes their listings state, so the plug fits the counterbore the bit cuts.
Can I use a countersink bit on stainless steel?
Not with the sets here. The DEWALT listing states its set is not recommended for stainless steel, and the msljtaim listing states not to use its set for stainless steel or iron plates. For stainless, look for a bit whose listing states it.
Related: best twist drill bit set, best countersink bit cobalt, standard drill bit size, center drill bit sizes and drill press speed chart. Also see our metal fab tools hub.




