Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Can You MIG Weld Aluminum Without Gas?

No: aluminum MIG needs argon shielding gas, and the wires in this guide run under argon through a spool gun or push feed setup.

Can You MIG Weld Aluminum Without Gas?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SÜA - ER4043 - MIG Aluminum Welding WireSÜA - ER4043 - MIG Aluminum Welding Wire9.6/10View on Amazon
  2. 2YESWELDER Magnesium Aluminum Welding Wire, ER5356YESWELDER Magnesium Aluminum Welding Wire, ER53569.6/10View on Amazon
  3. 3TOOLIOM ER5356 .030" Aluminum MIG Welding WireTOOLIOM ER5356 .030" Aluminum MIG Welding Wire9.6/10View on Amazon

An aluminum repair waits on the bench, and the MIG welder in the corner has no gas cylinder hooked up. Can you MIG weld aluminum without gas? No. Solid aluminum wire needs shielding gas around the puddle, and there is no self shielded flux core wire that welds aluminum, so a gasless setup cannot make a sound aluminum weld. The fix is a cylinder of argon, a spool gun or push feed setup for the soft wire, and one of the aluminum wires in this guide.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

SÜA - ER4043 - MIG Aluminum Welding Wire

SÜA - ER4043 - MIG Aluminum Welding Wire

SÜA9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An ER4043 aluminum MIG wire in a 4 spool pack, 1 lb per spool, for 6061, 6063 and cast aluminum.

Pros

  • 5% silicon wire, less sensitive to weld cracking
  • Suits 6061, 6063, 5052, 3004, 3003 and cast alloys 356.0, 357.0, 413.0 and 443.0
  • Melting range 1065 to 1170 F with a bright shiny deposit
  • 4 spools in the pack, with 0.030, 0.035 and 0.045 inch diameters available

Cons

  • Gray after anodizing, not white like 5356
  • No spool material stated in the listing
  • No warranty term is stated
  • Only the 0.030 inch size is in this pack; other diameters are menu choices in the listing
YESWELDER Magnesium Aluminum Welding Wire, ER5356

YESWELDER Magnesium Aluminum Welding Wire, ER5356

YESWELDER9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An ER5356 aluminum MIG wire, 1 lb spool of .030 inch wire that also lists all-position welding.

Pros

  • 5% magnesium for corrosion resistance in salt water
  • Stays white after anodizing for a clean color match
  • All-position wire: vertical, flat, up and corner welding
  • ABS plastic spool, durable and tough in the machine

Cons

  • 1 lb spool only, with no multi-pack size stated in this listing
  • No melting range or density stated
  • No warranty term is stated
  • Suits 5000 series only; not the wire for 6061, 6063 or cast aluminum
TOOLIOM ER5356 .030" Aluminum MIG Welding Wire

TOOLIOM ER5356 .030" Aluminum MIG Welding Wire

TOOLIOM9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An ER5356 aluminum MIG wire, 1 lb spool of .030 inch wire with 5% magnesium for 5000 series aluminum.

Pros

  • 5% magnesium for corrosion resistance in salt water
  • Bright white seam after anodizing
  • Suits 5000 series base metals 5050, 5052, 5083, 5356, 5454 and 5456
  • ABS plastic spool, durable and tough in the machine

Cons

  • 1 lb spool only, with no multi-pack size stated in this listing
  • No melting range or density stated
  • No warranty term is stated
  • No welding positions stated in the listing

Can you MIG weld aluminum without gas?

Molten aluminum oxidizes the moment it meets air, and an unshielded puddle picks up contamination that leaves a porous, weak bead. Gas MIG protects the puddle with argon from a cylinder, fed through the gun around solid wire. Self shielded flux core wire is hollow and filled with flux, but no self shielded flux core wire is made for aluminum, so the gasless route that works on steel does not carry over. Our can you MIG weld without gas guide covers the steel side, where flux core works.

Aluminum wire is soft, so it also needs a different feed path. A spool gun holds a small spool at the gun and feeds the wire a short distance, while a push feed setup uses a liner and drive rolls made for soft wire. Either way, the wire still runs under argon. See our wire feeder vs spool gun comparison if the feed setup is the part you still need to choose.

Side by side

TOOLIOM ER5356 YESWELDER ER5356 SÜA ER4043 What to note
Alloy ER5356, 5% magnesium ER5356, 5% magnesium ER4043, 5% silicon 5356 suits 5000 series; 4043 suits 6061, 6063 and cast
Diameter .030 inch .030 inch 0.030 inch All list the same diameter here
Spool size 1 lb spool 1 lb spool 4 spools, 1 lb each The SÜA listing is a 4 spool pack
Spool material ABS plastic ABS plastic Not stated Both 5356 listings state an ABS spool
Base metals listed 5050, 5052, 5083, 5356, 5454, 5456 5050, 5052, 5083, 5356, 5454, 5456 6061, 6063, 5052, 3004, 3003, cast 356.0, 357.0, 413.0, 443.0 Match the wire to the base metal
After anodizing White White Gray 5356 stays white; 4043 turns gray
Positions stated Not stated Vertical, flat, up, corner Not stated Only the YESWELDER listing states positions
Shielding Gas MIG wire Gas MIG wire Gas MIG wire Solid wire: needs shielding gas

The wires here are all solid wire for gas MIG: none of them welds without argon. Match the alloy to the base metal, then the diameter to the job. Our aluminum MIG wire 5356 vs 4043 guide compares the alloys in detail.

Aluminum MIG wire for the job

With argon on the cylinder and a spool gun or push feed setup on the machine, the wire is the last choice: 5356 for 5000 series aluminum, 4043 for 6061, 6063 and cast aluminum.

Which wire for which aluminum

ER5356 is the wire for 5000 series base metal: the TOOLIOM and YESWELDER listings both name 5050, 5052, 5083, 5356, 5454 and 5456, and both state the seam stays white after anodizing. ER4043 is the wire for 6061, 6063, 5052, 3004, 3003 and cast alloys 356.0, 357.0, 413.0 and 443.0, and it turns gray after anodizing. The best aluminum MIG wire roundup scores aluminum wires for shop work.

Diameter is the same across the listings here: the 5356 spools are .030 inch and the SÜA pack is 0.030 inch, with 0.035 and 0.045 inch sizes also listed for the SÜA wire (on Amazon). Pick the diameter the machine and the joint call for, and check the wire label and the machine manual before welding.

Gas and fume safety. Welding aluminum still makes fumes, so weld with ventilation or outdoors with your head out of the plume, and wear a welding helmet, gloves and long sleeves. Chain the argon cylinder upright so it cannot fall, and clear anything flammable from the area.

For more options, see our welding consumables guides.

FAQ for welders

Can I MIG weld aluminum with flux core wire?

No. No self shielded flux core wire welds aluminum. Aluminum MIG needs solid wire under argon shielding gas, fed through a spool gun or a push feed setup.

What gas do I need for aluminum MIG?

Pure argon is the standard gas for aluminum MIG. The wires in this guide are solid aluminum wire for the MIG process, and argon shields the puddle from air while you weld. Check the wire label and the machine manual for the gas they call for.

Which aluminum wire should I use, 5356 or 4043?

Match the wire to the base metal. ER5356 suits 5000 series aluminum such as 5050, 5052, 5083, 5356, 5454 and 5456, and it stays white after anodizing. ER4043 suits 6061, 6063, 5052, 3004, 3003 and cast alloys 356.0, 357.0, 413.0 and 443.0, and it turns gray after anodizing.

Why does aluminum MIG need a spool gun?

Aluminum wire is soft, so a long feed path through a standard liner can kink and jam the wire. A spool gun holds the spool at the gun and feeds the wire a short distance, which keeps the soft wire moving. A push feed setup with the right liner and drive rolls is the other way to feed it.

Can I weld aluminum with a standard MIG welder?

Yes, if the machine runs gas MIG and feeds aluminum wire. You need argon shielding gas, a spool gun or push feed setup for the soft wire, and a wire that matches the base metal. Our how to choose a MIG welder guide covers what to check in the listing before you buy.

Related: best aluminum MIG wire, best MIG welding wire, spool gun for Lincoln MIG welder, and the aluminum MIG wire vs TIG rod comparison. Also see our can you MIG weld without gas guide.

More buying guides

TIG Welders ·

How to TIG Weld without a Foot Pedal

How to TIG weld without a foot pedal using torch switches, lift TIG start, and machine heat settings for clean welds in the shop…