Best Metal Scribe (2026): 5 Shop Picks for Layout
Five metal scribes for layout work, compared by tip material, magnet, pack size, replacement tips and the warranty each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMalco A409.6/10View on Amazon - 2
Best 2-PackGlieskir 2-Pack9.6/10View on Amazon - 3
Best SingleGeneral Tools 88CM9.6/10View on Amazon - 4
Best 4-PackNEPAK 4-Pack9.6/10View on Amazon
Layout is the quiet part of metal work. Before the first cut or tack, you need a line on the steel that will not rub off, and a pencil will not do it on mill scale. A metal scribe scratches a fine, permanent line into the surface so the cut lands where you marked it. A marker line wipes off with a thumb; a scribed line survives oil, handling and the trip across the shop. This guide covers the best metal scribe options: five scribes compared by tip material, magnet, pack size and what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Malco A40: Five teeth, 10 scribing depths, hang hole, magnet and a limited lifetime warranty. Check price on Amazon
- Best 2-Pack Glieskir 2-Pack: Two scribers with 10 replacement tips, end magnets and a 1-year warranty. Check price on Amazon
- Best Single General Tools 88CM: Tungsten carbide tip with magnet, pocket clip and a reversing chuck. Check price on Amazon
- Best 4-Pack NEPAK 4-Pack: Four scribers with 24 replacement tips and magnets for the bench. Check price on Amazon
The machines

Malco A40 USA Made Sheet Metal Scriber
A USA-made sheet metal scriber with five steel teeth that produce 10 scribing depths, a hang hole, a magnet and a reusable pouch, backed by a limited lifetime warranty.
Pros
- Five teeth produce 10 scribing depths
- Limited lifetime warranty stated
- Hang hole and magnet keep it handy on the job
- Reusable vinyl pouch included for storage
Cons
- No tungsten carbide tip
- No replacement tip is listed
- 1.6 ounce weight with a 0.25 in diameter

Glieskir 2-Pack Tungsten Carbide Scriber Set
A 2-pack of tungsten carbide scribers with 10 replacement tips, end magnets, knurled aluminum handles and a 1-year warranty.
Pros
- 2 scribers plus 10 replacement carbide tips
- Magnet at the end of each pen
- Knurled aluminum handle with pocket clip
- 1-year warranty stated
Cons
- No safety listing is stated
- Line size 0.3mm suits fine marks only
- Unit count reads 4 count for a 2-pack
- Hardness stated on the Rockwell A scale, an unusual choice

General Tools 88CM Tungsten Carbide Scribe
A tungsten carbide scribe with a magnetic end, knurled aluminum handle, pocket clip and a replaceable tip with a reversing chuck.
Pros
- Tungsten carbide tip marks hardened steel, stainless, ceramics and glass
- Magnetic end picks up small parts and steel chips
- Replaceable tip with a chuck for reversing the point
- Knurled aluminum handle with pocket clip
Cons
- Warranty field reads Warranty with no term, so it scores zero
- Item weight listed as 0.27 g, a likely unit error
- No replacement tip count is stated
- Single scribe only

NEPAK 4 Pack Metal Scribe Tool,Tungsten Carbide
A 4-pack of tungsten carbide scriber pens with magnets, pocket clips and 24 replacement tips, with a 0.3mm line size.
Pros
- 4 scribers plus 24 replacement tips
- Permanent magnets on every pen
- Knurled aluminum handle with pocket clip
- 0.3mm line size for fine marks
Cons
- No warranty term is stated
- No safety listing is stated
- Style field reads disposable

Tungsten Carbide Scriber, Knurled Aluminum Handle
A 4-pack of tungsten carbide scribers with magnets, 24 replacement nibs and a 6-inch stainless steel ruler.
Pros
- 4 scribers with magnets and pocket clips
- 24 replacement nibs with protective cases
- 6-inch stainless steel ruler included
- Knurled aluminum handle, tip cap included
Cons
- Unit count reads 3 count for a 4-pack
- No warranty term is stated
- No safety listing is stated
Spec sheet comparison
| Model | Gear Score | Tip | Pack | Magnet | Extras | Warranty |
|---|---|---|---|---|---|---|
| Malco A40 | 9.6/10 | 5 teeth, 10 depths | 1 | Yes | Reusable pouch, hang hole | Limited lifetime |
| Glieskir 2-Pack | 9.6/10 | Tungsten carbide | 2 + 10 tips | Yes | Tip sleeves | 1 year |
| General Tools 88CM | 9.6/10 | Tungsten carbide | 1, replaceable | Yes | Pocket clip, chuck | Not stated |
| NEPAK 4-Pack | 9.6/10 | Tungsten carbide | 4 + 24 tips | Yes | Pocket clip | Not stated |
| PSMYP 4-Pack | 9.5/10 | Tungsten carbide | 4 + 24 nibs + ruler | Yes | Pocket clip, tip cap | Not stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 22 October 2026.
How we picked the best metal scribe
Five scribes went head to head on the things that make a mark: tip material, magnet, replacement tips and carry. Four of the five use tungsten carbide tips; the Malco takes a different path with a five-tooth steel head that makes 10 scribing depths. All five list a magnet, and pack sizes run from a single scribe to 4-packs with 24 replacement tips. The Glieskir splits the difference with a 2-pack and 10 tips.
The listings also disagree with themselves, and that costs them. The NEPAK bullets say 4 additional tips while its title and spec table say 24; the PSMYP title says 4-pack while its unit count reads 3 count; the General Tools spec table lists the item weight as 0.27 g. Every figure in this guide comes straight from the listings, and the tables keep the gaps visible.
Buying guide: metal scribes
Tip material
Tungsten carbide is the standard here: four listings state it, and the General Tools listing says it marks hardened steel, stainless steel, ceramics and glass. The Malco takes a different path with five steel teeth that produce 10 scribing depths. Carbide stays sharp longer; teeth give preset depths.
Magnet or no magnet
All five listings state a magnet. The uses the listings give: picking up small parts, retrieving steel chips and filings from hard-to-reach places, and keeping the tool handy on the machine. The Glieskir and PSMYP magnets sit at the end of the pen; the General Tools 88CM has a magnetic end plus a pocket clip.
Pack size and replacement tips
Scribes are easy to lose and tips wear. Pack counts here: single (General Tools, Malco), 2-pack (Glieskir) and 4-pack (NEPAK, PSMYP). Replacement tips: 24 on the NEPAK, 24 nibs on the PSMYP, 10 on the Glieskir, and a replaceable tip with a reversing chuck on the General Tools. The Malco lists no replacement tip.
Pocket carry
A scribe lives in the pocket. The General Tools, NEPAK, Glieskir and PSMYP list a pocket clip; the Malco stores in a pocket, pouch or tool box and ships in a reusable vinyl pouch. The Glieskir and PSMYP add protective tip sleeves or caps so the point does not find your finger.
Line visibility
A scribe line has to show. Layout fluid turns the steel blue so the scratch stands out; the General Tools listing even says to apply layout fluid and scribe away. On stainless or polished stock the line shows without it. Deepen the line with a second pass when the cut has to follow it exactly.
Storing the scribe
A scribe earns its keep only if it is at hand. Pocket clips come on four of the five picks; the Malco ships in a reusable vinyl pouch for the pocket or tool box. Tip sleeves and caps on the Glieskir and PSMYP keep the point sharp and your pocket safe. The magnet on each one also parks the tool on the machine, which beats digging through the toolbox.
When the listing is thin
Thin listings cost their products here. The NEPAK bullets say 4 additional tips against 24 in the title; the PSMYP unit count reads 3 count against a 4-pack title; the General Tools weight reads 0.27 g. This guide reports every figure as stated and scores the contradictions down, so the tables never hide them.
Use as directed. A scribe point is sharp enough to cut skin: keep the protective cap or sleeve on in the pocket, and never point it toward your hand when marking. Brush steel chips away from the mark instead of blowing them. Check the point before each layout session; a chipped tip tears the line. Keep the tool off the weld table while the stinger is live.
Before You Strike an Arc
- Check the tip on arrival: carbide should sit centered and tight, and the chuck or cap should thread smoothly.
- Confirm the magnet holds the tool to the machine before trusting it there.
- Count the replacement tips against the listing: 24, 24, 10 or a single replaceable tip per the listings here.
- No listing here states a safety standard, so inspect the handle and tip seating on day one.
FAQ for welders
What is a metal scribe?
A metal scribe is a hardened point, usually tungsten carbide, used to scratch layout lines into metal. The line survives handling, oil and layout fluid where a marker rubs off. Four of the five picks here use tungsten carbide tips.
Why is it hard to use a scribe on metal?
It is not hard, but it takes a steady hand: the tip must stay upright and the pressure even, or the line wanders. A knurled handle helps, and four listings here state one. Practice on scrap first, and use layout fluid so the line shows.
How do I use a scribe for sheet metal layout?
Mark the measurement, set the scribe point on it and pull the tool along a straightedge with steady pressure. The Malco A40 five teeth make 10 preset depths for repeated marks. One pass is usually enough; a second pass deepens the line.
Do I need the magnet?
Not for marking, but it earns its keep: every pick here has one for picking up small parts and retrieving steel chips from tight spots. It also parks the tool on the machine so it does not roll away.
How long does a carbide tip last?
The listings give no lifespan, which is why replacement tips matter: the NEPAK and PSMYP include 24, the Glieskir 10, and the General Tools tip is replaceable with a reversing chuck. The Malco lists no replacement tip.
Can a scribe mark hardened steel?
The General Tools listing says its tungsten carbide tip marks hardened steel, stainless steel, ceramics and glass. The other carbide listings name hardened steel and tile. For the hardest stock, a fresh carbide point and steady pressure work best.
Related: the best angle grinder for cutting metal, the best hacksaw for cutting steel, the bench vise vs welding vise comparison, the angle clamps for welding and the metal fab tools hub.
Scoring, line by line
Each scribe is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. Scribes state no electrical safety listing, so every scribe here scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Malco A40 | 9.6 | 29 | 20 | 20 | n/a | 4 |
| Glieskir 2-Pack | 9.6 | 27 | 19 | 21 | n/a | 3 |
| General Tools 88CM | 9.6 | 28 | 20 | 20 | n/a | 0 |
| NEPAK 4-Pack | 9.6 | 28 | 19 | 21 | n/a | 0 |
| PSMYP 4-Pack | 9.5 | 27 | 19 | 21 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.





