Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Measuring Gauges for Metalworking (2026)

Four gauges for metalworking, compared on radius range, angle markings, taper scales and weld inspection, from what each listing states.

Best Measuring Gauges for Metalworking (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Hicarer 3 Piece Welding Gauge SetBest OverallHicarer 3 Piece Welding Gauge Set9.5/10View on Amazon
  2. 2Bonbo 26 Piece Radius Gauge SetWidest Radius RangeBonbo 26 Piece Radius Gauge Set9.5/10View on Amazon
  3. 3Viliqiou Taper Gauge 1-15mmBest Dual ScaleViliqiou Taper Gauge 1-15mm9.4/10View on Amazon
  4. 4HARFINGTON Drill Bit Angle GaugesBest for Drill AnglesHARFINGTON Drill Bit Angle Gauges9.3/10View on Amazon

A fillet weld can look smooth and still leave a gap at the root, and a drilled hole can look round while the bit angle drifts off centre. The difference between a part that fits and a part that gets cut apart and redone is often a gauge that reads true. This roundup covers the best measuring gauges for metalworking for a home or small shop, comparing gauges on range, markings, material and what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Hicarer 3 Piece Welding Gauge Set: Three stainless steel weld inspection tools in one set, with fillet sizes from 1/8 inch to 1 inch. Check price on Amazon
  • Widest Radius Range Bonbo 26 Piece Radius Gauge Set: 26 individually marked gauges from 0.010 inch to 0.500 inch in satin chrome steel. Check price on Amazon
  • Best Dual Scale Viliqiou Taper Gauge 1-15mm: One taper gauge reads 1 to 15 mm and 1/64 inch to 5/8 inch, with laser engraved markings. Check price on Amazon
  • Best for Drill Angles HARFINGTON Drill Bit Angle Gauges: Marked angles from 60 to 160 degrees in 2CR13 stainless steel. Check price on Amazon

The machines

Hicarer 3 Piece Welding Gauge Set Weld Inspection

Hicarer 3 Piece Welding Gauge Set Weld Inspection

Hicarer9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A three piece stainless steel set for weld inspection, with a single fillet gauge, a seven piece fillet gauge set and a bridge cam gauge, covering fillet legs, throats, undercuts and preparation angles.

Pros

  • Three tools in one set: single fillet gauge, seven piece fillet set and bridge cam gauge
  • Checks fillet leg and throat dimensions, undercuts, porosity, dimples and pitting
  • Inch fillet sizes from 1/8 inch to 1 inch, with metric sizes from 3.2 to 25.4 mm
  • Stainless steel with a brushed surface and laser inscriptions for clear reading

Cons

  • No warranty term is stated
  • The single fillet gauge is thin at 0.04 inch, so it needs a gentle hand in the shop
  • The bridge cam gauge measures 3.94 by 2.76 inches, which limits its reach on large work
  • Suits weld inspection only; it does not measure radiuses or drill bit angles
26-PCS Radius Gauge Set 3602-5025

26-PCS Radius Gauge Set 3602-5025

Bonbo9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 26 piece set of individually marked radius gauges in satin chrome steel, covering radiuses from 0.010 inch to 0.500 inch for checking concave and convex fillets on metal parts.

Pros

  • 26 gauges cover radiuses from 0.010 inch to 0.500 inch in small steps
  • Each gauge is individually marked with precision etched numbers for quick reading
  • Satin chrome steel with high hardness and wear and corrosion resistance
  • A protective sleeve keeps each gauge in order and guards against dings and scratches

Cons

  • No warranty term is stated
  • Radius gauges only; the set does not check angles, tapers or weld size
  • The smallest gauges start at 0.010 inch, so very small fillets need a different tool
  • A 26 piece set takes more bench space than a single gauge
Stainless Steel Double Sided Taper Gauge 1-15mm

Stainless Steel Double Sided Taper Gauge 1-15mm

Viliqiou9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A double sided stainless steel taper gauge with laser engraved markings, reading metric sizes from 1 to 15 mm and imperial sizes from 1/64 inch to 5/8 inch for apertures and inner diameters.

Pros

  • Dual scales read metric from 1 to 15 mm and imperial from 1/64 inch to 5/8 inch
  • Laser engraved markings stay clear and easy to read
  • Stainless steel resists rust and corrosion in the shop
  • Small size suits carrying to the work instead of bringing the work to the bench

Cons

  • Suits apertures and inner diameters only; it does not check radius, angle or weld size
  • One gauge means one taper at a time, with no second gauge for a quick comparison
  • The thin end of a taper gauge can bend if it is forced into a tight gap
  • Small size makes the markings harder to read at arm's length in poor light
HARFINGTON Drill Bit Angle Gauges 60°-160° Drill

HARFINGTON Drill Bit Angle Gauges 60°-160° Drill

HARFINGTON9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A stainless steel angle gauge marked in degrees from 60 to 160 for checking drill bit angles, in a compact size of about 80 by 80 by 2 mm for the bench or the tool roll.

Pros

  • Marked with 60, 82, 90, 118, 120, 135, 150 and 160 degrees
  • 2CR13 stainless steel resists rust and suits long service in the shop
  • Marked degrees give easy to read and accurate values
  • Compact size of about 80 by 80 by 2 mm fits the bench or a tool roll

Cons

  • Angle checking only; it does not measure radius, taper or weld size
  • One gauge, one set of angles; a bit outside 60 to 160 degrees needs another gauge
  • The 2 mm thickness is thin, so the gauge needs care to stay flat
  • The gauge reads angles only, so it cannot confirm a drill bit diameter on its own

Spec sheet comparison

Model Gear Score Type Range Pieces Material Warranty
Hicarer 3 Piece Welding Gauge Set 9.5/10 Weld inspection set 1/8 to 1 in fillet 3 tools Stainless steel Not stated
Bonbo 26 Piece Radius Gauge Set 9.5/10 Radius gauge set 0.010 to 0.500 in 26 Satin chrome steel Not stated
Viliqiou Taper Gauge 1-15mm 9.4/10 Taper gauge 1 to 15 mm 1 Stainless steel Not stated
HARFINGTON Drill Bit Angle Gauges 9.3/10 Angle gauge 60 to 160 degrees Not stated 2CR13 stainless steel Not stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 November 2026.

How to choose the best measuring gauges for metalworking

Radius range

Radius gauges earn their keep when a fillet has to match a drawing or a mating part. The Bonbo set covers radiuses from 0.010 inch to 0.500 inch, with steps of 0.005 inch at the small end, 0.010 inch through the middle, 0.020 inch higher up and 0.050 inch at the large end. That spread suits a shop that checks both small fillets on brackets and larger radiuses on plate work. A single gauge cannot cover that spread, so the set suits a bench that sees varied radius work.

Angle and taper

Angle gauges and taper gauges answer different questions. The HARFINGTON gauge is marked with 60, 82, 90, 118, 120, 135, 150 and 160 degrees, which suits checking drill bit angles before a bit goes back into service. The Viliqiou taper gauge reads metric sizes from 1 to 15 mm and imperial sizes from 1/64 inch to 5/8 inch, which suits apertures and inner diameters where a gap needs a quick check. Pick the angle gauge for drill work and the taper gauge for gaps and bores.

Weld inspection

Weld inspection gauges check the joint itself, not just the part around it. The Hicarer set includes a single fillet weld depth gauge, a seven piece fillet weld gauge set and a bridge cam welding gauge, all in stainless steel. The inch fillet size runs from 1/8 inch to 1 inch and the metric size runs from 3.2 to 25.4 mm, and the set checks fillet leg dimensions, fillet throat dimensions, undercuts, porosity, dimples and pitting. The bridge cam gauge also measures preparation angles, fillet weld lengths, rebar depths, undercuts and pitting, and it can be fixed in any position by tightening the screws.

Material and markings

All four gauges here are steel, and the markings decide how fast a reading comes. The Bonbo gauges use precision etched numbers on satin chrome steel, the Viliqiou gauge uses laser engraved markings, and the Hicarer set uses laser inscriptions. Etched and engraved markings stay readable after handling, which matters when a gauge lives in a tool roll or a shop drawer. The HARFINGTON gauge is made of 2CR13 stainless steel, and the maker lists anti rust construction for long service life.

Reading the scale

A gauge only helps if the reading is taken the same way each time. Hold the gauge flat against the work, match the curve or angle by eye, and read the marking that fits without forcing the gauge into the gap. Check the fit in good light, and wipe the gauge clean before putting it away so grit does not wear the markings. If two gauges both seem to fit, take the reading again with the gauge seated flat, and trust the one that sits flush without a gap at the edge.

Before You Strike an Arc

  • Check each gauge against a known edge or angle before trusting it on a part.
  • Wipe the gauge clean and dry before putting it back in its holder or sleeve.
  • Keep the gauge flat against the work and read the marking at eye level.
  • Set the work down and clamp it before measuring a fillet or a gap.
  • Check that the bridge cam screws hold their position before taking a reading.

FAQ for welders

What gauge measures a fillet radius?

A radius gauge set measures a fillet radius. The Bonbo set here covers radiuses from 0.010 inch to 0.500 inch, with each gauge individually marked. Hold the gauge against the concave or convex fillet and read the size that fits flush.

How do I check a drill bit angle?

Use an angle gauge marked in degrees. The HARFINGTON gauge here is marked with 60, 82, 90, 118, 120, 135, 150 and 160 degrees. Match the bit point to the marked angle and read the value that lines up with the cutting edge.

What does a taper gauge measure?

A taper gauge measures apertures and inner diameters. The Viliqiou gauge here reads metric sizes from 1 to 15 mm and imperial sizes from 1/64 inch to 5/8 inch. Slide the taper into the gap or bore and read the scale where it stops.

What can a bridge cam gauge check?

A bridge cam gauge checks weld preparation and weld quality. The Hicarer bridge cam gauge here measures preparation angles, fillet weld lengths, rebar depths, undercuts and pitting. It can be fixed in any position by tightening the screws, which helps when reading a joint that is already tacked up.

Related: measuring gauge tool, weld size gauge, best bore gauge, types of feeler gauge, feeler gauge size chart, best sheet metal gauge thickness tool.

Scoring, line by line

Each gauge is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Gauges have no electrical safety listing to state, so every gauge here scores zero on that criterion, and the ranking comes from the other criteria. No listing here states a warranty term, so every gauge here scores zero on warranty as well.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Hicarer 3 Piece Welding Gauge Set 9.5 30 21 21 0 0
Bonbo 26 Piece Radius Gauge Set 9.5 29 21 20 0 0
Viliqiou Taper Gauge 1-15mm 9.4 28 20 20 0 0
HARFINGTON Drill Bit Angle Gauges 9.3 26 19 19 0 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.

More buying guides