Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Try Square vs Combination Square: Which One Should You Buy?

A try square holds a fixed right angle, while a combination square slides, turns and swaps heads; here is how two of each compare on size, graduations, angles, build and warranty.

Try Square vs Combination Square: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Johnson Level & Tool 1910-0800 Inch/MetricJohnson Level & Tool 1910-0800 Inch/Metric9.5/10View on Amazon
  2. 212" 4 Combination Square Ruler Set Protractor12" 4 Combination Square Ruler Set Protractor9.5/10View on Amazon
  3. 3POWERTEC L Square 3pc, Try SquarePOWERTEC L Square 3pc, Try Square9.5/10View on Amazon
  4. 4DUEBEL Combination SquareDUEBEL Combination Square9.5/10View on Amazon

Verdict. Pick a try square for marking and checking right angles. Pick a combination square when the work also needs angles, height and depth checks, or a center head.

A square that reads true saves more time than any other layout tool on the bench. The question in try square vs combination square is how much the tool has to do: hold a fixed right angle, or slide, turn and swap heads. This comparison puts them side by side from the listings.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The four squares

Johnson Level & Tool 1910-0800 Inch/Metric

Johnson Level & Tool 1910-0800 Inch/Metric

Johnson9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-inch try and mitre square with a Structo-Cast handle, a stainless steel blade and etched graduations, with a 1 year warranty.

Pros

  • Stainless steel blade with a Structo-Cast handle
  • Checks right angles and 45 degree angles
  • Graduations in 1/8 inch, mm and cm
  • 1 Year Warranty stated in the listing

Cons

  • One size only, 8 inches
  • No bubble level is stated
  • Cannot check height or depth like a sliding head
  • Finest graduation stated is 1 mm, not 64ths
12" 4 Combination Square Ruler Set Protractor

12" 4 Combination Square Ruler Set Protractor

NTSUMI9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-inch, 4-piece combination square set with a protractor head and a center head, in satin chrome steel with 4R graduations.

Pros

  • Four pieces: ruler, square head, protractor head, center head
  • 12-inch blade for layout, height, depth and angle checks
  • 4R graduations on a satin chrome blade
  • Square head with horizontal and scoring points

Cons

  • No warranty term is stated
  • One blade length, 12 inches
  • No accuracy figure is stated for the protractor head
  • No case or storage is stated
POWERTEC L Square 3pc, Try Square

POWERTEC L Square 3pc, Try Square

POWERTEC9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece set of L-shaped try squares in aluminum with bubble levels, in three lengths for marking and checking right angles.

Pros

  • Three lengths: 6-1/4, 10-3/16 and 16-1/8 inches
  • Fluorescent green bubble levels on each square
  • Standard and metric graduations, anodized aluminum body
  • Hanging holes for storage and a lightweight build

Cons

  • No warranty term is stated
  • Fixed 90 degrees only, with no protractor head
  • Three separate squares to store and keep track of
  • No 45 degree angle is stated
DUEBEL Combination Square

DUEBEL Combination Square

DUEBEL9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-inch combination square with a hardened stainless steel blade, a 0 to 180 degree range and 4R graduations etched by laser.

Pros

  • 0 to 180 degree range, accuracy 5' / 0.08 degrees
  • 4R graduations: 8ths, 16ths, 32nds and 64ths
  • Hardened and tempered stainless steel blade, satin chrome
  • Horizontal bubble, marking needle, fine adjustments

Cons

  • No warranty term is stated
  • One blade length, 12 inches
  • Single head only, with no spare heads in the box
  • Zinc alloy head, not steel

Side by side

Johnson Structo-Cast Try Square NTSUMI Combination Square Set POWERTEC L Square 3pc DUEBEL Combination Square
Gear Score 65 61 60 59
Side Try square Combination square Try square Combination square
Size 8 in 12 in 6-1/4, 10-3/16 and 16-1/8 in 12 in
Graduations 1/8 in, mm and cm 4R Standard and metric 4R, 8ths to 64ths
Angle range Right angles and 45 degrees Protractor head included 90 degrees 0 to 180 degrees
Level Not stated Horizontal on square head Bubble levels Horizontal bubble
Pieces 1 square 4 pieces 3 pieces 1 square, head separates
Material Stainless blade, Structo-Cast handle High quality steel Aluminum, anodized Hardened stainless blade, zinc alloy head
Warranty 1 Year Not stated Not stated Not stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 November 2026. Only the Johnson states a warranty term.

Try Square vs Combination Square: What Separates Them

A try square holds a fixed blade at a right angle. A combination square lets the head slide along the blade and swap for a protractor head or a center head, so the same tool checks angles, height, depth and centers. The try squares state 90 degrees and, in the Johnson, 45 degrees; the combination squares state a 0 to 180 degree range or a protractor head.

Size and reach

The POWERTEC set spans three lengths, 6-1/4, 10-3/16 and 16-1/8 inches, so a small square marks joints and the long square checks panels. The Johnson is a single 8-inch square. Both combination squares use a 12-inch blade.

Graduations and angles

The DUEBEL states 4R graduations in 8ths, 16ths, 32nds and 64ths, and the NTSUMI states 4R graduations on a satin chrome blade. The Johnson states graduations in 1/8 inch, mm and cm, etched in black, and the POWERTEC states standard and metric measurements. On angles, the DUEBEL states a 0 to 180 degree range, and the NTSUMI includes a protractor head.

Build and materials

The POWERTEC set is anodized aluminum, the Johnson has a stainless blade and a Structo-Cast handle, the DUEBEL has a hardened stainless blade and a zinc alloy head, and the NTSUMI has a satin chrome steel blade. The POWERTEC set has fluorescent green bubble levels, the DUEBEL has a horizontal bubble, and the NTSUMI square head has horizontal and scoring points.

What is in the box

The NTSUMI set includes four pieces: a stainless steel ruler, a square head, a protractor head and a center head. The POWERTEC set includes three squares in three lengths. The DUEBEL is a single square whose head separates from the blade.

Choose the try square if

  • Marking and checking right angles.
  • A fixed square with no sliding parts.
  • A bubble level on the square, as on the POWERTEC set.
  • A stated warranty term, as on the Johnson.

Choose the combination square if

  • Measuring angles beyond 90 degrees.
  • Checking height and depth with one tool.
  • A protractor head or a center head.
  • Fine graduations down to 64ths, as on the DUEBEL.

Before You Strike an Arc

  • Check the square against a straight edge on arrival before marking a cut.
  • Confirm the graduations read clearly and, on a combination square, the head locks where you set it.
  • Wipe the blade clean after use and store the square flat or hung.
  • Check the bubble level reads true on a flat surface before trusting it for layout.

FAQ for welders

Which square is better for checking a right angle?

Both sides check right angles. The POWERTEC set and the Johnson square state 90 degree checking, with the Johnson adding 45 degree angles.

What does 4R graduation mean on a combination square?

4R means the blade carries four graduation scales, and the DUEBEL listing names them as 8ths, 16ths, 32nds and 64ths. The NTSUMI listing also states 4R graduations.

Can a combination square measure angles other than 90 degrees?

Yes. The DUEBEL states a 0 to 180 degree range with accuracy of 5′ / 0.08 degrees, and the NTSUMI set includes a protractor head.

Which of these squares states a warranty?

Only the Johnson, with a 1 Year Warranty in its listing. The other three state no warranty term, though the DUEBEL listing states after-sale service is 24h online.

Related: best combination square set, best L square measuring tool, uses for a combination square, machinist square vs combination square, and the measuring and layout hub.

Scoring, line by line

All four squares are scored out of 10 on performance, build, value, safety listing and warranty, with the weights on the How We Pick page. No listing states a safety listing, so safety scores 0, and only the Johnson states a warranty term.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Johnson Structo-Cast Try Square 9.5 29 21 20 0 2
NTSUMI Combination Square Set 9.5 32 21 21 0 0
POWERTEC L Square 3pc 9.5 30 21 21 0 0
DUEBEL Combination Square 9.5 30 21 20 0 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.

More buying guides