Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Bore Gauge (2026): 5 Dial and Digital Picks

Five dial and digital bore gauges from 0.7 to 6 inches, compared on measuring range, depth, resolution, anvils and the warranty each listing states.

Best Bore Gauge (2026): 5 Dial and Digital Picks
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Neoteck NTK301 DialBest OverallNeoteck NTK301 Dial9.7/10View on Amazon
  2. 2Accusize EE20-2416Finest GraduationAccusize EE20-24169.7/10View on Amazon
  3. 3BOBOVAV BBA018Best DigitalBOBOVAV BBA0189.6/10View on Amazon
  4. 4ALLmeter Dial Bore GaugeDeep Reach DialALLmeter Dial Bore Gauge9.6/10View on Amazon

An engine cylinder that has run hard can wear out of round, and a piston bore can taper from top to bottom. A ruler cannot show that wear. That is the job the best bore gauge is built for: it reaches inside the bore and shows the size, the taper and the out-of-round shape so you can judge what the cylinder needs next.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Neoteck NTK301 Dial: A 0.7 to 6 inch range with 23 anvils, two rods, a 6 inch depth and the only 18 month warranty here. Check price on Amazon
  • Finest Graduation Accusize EE20-2416: A 0.0001 inch graduation on an AGD Group 2 indicator, with carbide-tipped contacts and a bezel lock for zero setting. Check price on Amazon
  • Best Digital BOBOVAV BBA018: A digital indicator, a 0.7 to 6 inch range, 23 anvils and two rods for small and large bores. Check price on Amazon
  • Deep Reach Dial ALLmeter Dial Bore Gauge: A self-centering dial gauge with 23 anvils and guides that reach 6 inches deep, in a fitted ABS case. Check price on Amazon

The machines

Neoteck Dial Bore Gauge with 0.7"-6"/0.0005"

Neoteck Dial Bore Gauge with 0.7"-6"/0.0005"

Neoteck9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A dial bore gauge covering 0.7 to 6 inches with 23 anvils, two measuring rods, a 6 inch depth and an 18 month warranty, the longest stated term here.

Pros

  • A 0.7 to 6 inch range that covers small bores and large cylinders alike
  • 23 anvils in sizes from 0.7-0.8 inch to 3.8-4 inch
  • Two measuring rods for small and large bores
  • 18 month warranty, the longest term stated here

Cons

  • Dial readout only, with no digital display
  • 0.0005 inch accuracy is coarser than the 0.0001 inch graduation of the Accusize
  • Two rods to swap when moving between small and large bores
  • Depth stops at 6 inches
Accusize Dial Bore Gauge Set, 1.4-6 in Range

Accusize Dial Bore Gauge Set, 1.4-6 in Range

Accusize Industrial Tools9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A dial bore gauge with a 0.0001 inch graduation on an AGD Group 2 indicator, carbide-tipped contacts, 15 anvils and 4 spacers for 1.4 to 6 inch bores.

Pros

  • 0.0001 inch graduation, the finest smallest reading here
  • AGD Group 2 indicator with a 0 to 0.05 inch dial
  • Carbide-tipped contact points for extended wear and abrasion resistance
  • Bezel lock for zero setting, plus an extension holder and fitted case

Cons

  • Range starts at 1.4 inches, so small bores need another gauge
  • Warranty covers 1 month only
  • 15 anvils is fewer than the 23 in three other sets
  • Dial readout only, with no digital display
BOBOVAV Digital Dial Bore Gauge Set,0.7-6"

BOBOVAV Digital Dial Bore Gauge Set,0.7-6"

BOBOVAV9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A digital dial bore gauge covering 0.7 to 6 inches with 23 anvils, two measuring rods, a 6 inch depth and self-centering heads with guide wheels.

Pros

  • Digital indicator for a direct reading
  • 0.7 to 6 inch range with a 6 inch depth
  • 23 anvils plus 3 washers for fine adjustment
  • Self-centering heads with guide wheels for steady positioning

Cons

  • No warranty term is stated
  • 0.0005 inch accuracy is coarser than the 0.0001 inch graduation of the Accusize
  • Two rods to swap when moving between small and large bores
  • Depth stops at 6 inches
ALLmeter Dial Bore Gauge,0.7-6in Range,0.0005in

ALLmeter Dial Bore Gauge,0.7-6in Range,0.0005in

ALLmeter9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A dial bore gauge covering 0.7 to 6 inches with 23 anvils, a self-centering design and guides that reach 5 to 6 inches deep, in a fitted ABS case.

Pros

  • 0.7 to 6 inch range for engine and bearing work
  • 23 anvils for a wide spread of bore sizes
  • Self-centering design for steady positioning in the bore
  • Guides reach 5 to 6 inches deep, with a fitted ABS case

Cons

  • No warranty term is stated
  • Dial readout only, with no digital display
  • 0.0005 inch resolution is coarser than the 0.0001 inch graduation of the Accusize
  • Reaches 6 inches only with the extended guides fitted
Neoteck 2"-6"/0.0005" Digital Indicator Bore Gauge

Neoteck 2"-6"/0.0005" Digital Indicator Bore Gauge

Neoteck9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A digital bore gauge covering 2 to 6 inches with a 5.9 inch depth, 12 anvils, self-centering carbide anvils and insulated grips for deep engine cylinder measurement.

Pros

  • Digital indicator with a 0.0005 inch resolution
  • Self-centering with carbide anvils for wear resistance
  • Insulated grips for comfortable measuring
  • Sealed gauge head with a storage case included

Cons

  • Range starts at 2 inches, the narrowest low end here
  • 12 anvils is the fewest in this roundup
  • Digital readout only, with no dial indicator in the set
  • 5.9 inch depth is the shallowest stated depth here

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Range Depth Smallest reading Anvils Indicator Warranty
Neoteck NTK301 Dial 9.7/10 0.7 to 6 in 150 mm (6 in) 0.0005 in 23 Dial 18 months
Accusize EE20-2416 9.7/10 1.4 to 6 in Not stated 0.0001 in 15 Dial 1 month
BOBOVAV BBA018 9.6/10 0.7 to 6 in 6 in (150 mm) 0.0005 in 23 Digital None stated
ALLmeter Dial Bore Gauge 9.6/10 0.7 to 6 in 5 to 6 in 0.0005 in 23 Dial None stated
Neoteck NTK313 Digital 9.6/10 2 to 6 in 150 mm (5.9 in) 0.0005 in 12 Digital None stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 19 November 2026.

How the gauges were scored

Each gauge is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Bore gauges have no electrical safety listing to state, so every gauge here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Neoteck NTK301 Dial 9.7 30 21 21 n/a 3
Accusize EE20-2416 9.7 32 21 20 n/a 1
BOBOVAV BBA018 9.6 30 21 21 n/a 0
ALLmeter Dial Bore Gauge 9.6 29 20 21 n/a 0
Neoteck NTK313 Digital 9.6 28 20 20 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

How to pick the best bore gauge

Range and depth

Range decides which bores a gauge can measure at all. Three gauges here cover 0.7 to 6 inches, the Accusize covers 1.4 to 6 inches, and the Neoteck digital covers 2 to 6 inches. Depth decides how far down the bore the gauge can read: the Neoteck digital reaches 150 mm, stated as 5.9 inches, the BOBOVAV and the Neoteck dial reach 6 inches, and the ALLmeter reaches 5 to 6 inches. Match both figures to the smallest bore and the deepest cylinder you plan to measure.

Digital or dial indicator

Two gauges here use a digital indicator and three use a dial indicator. A digital indicator gives a direct number on a display, while a dial indicator shows a needle against a marked face. The Accusize dial reads in 0.0001 inch graduations, the finest smallest reading here, while the other four read to 0.0005 inch. Pick the display you read most easily, and remember that a finer graduation only helps if the zero setting is right.

Anvils and rods

Anvils set the gauge to the bore size, and rods set the depth. Three sets here include 23 anvils, the Accusize includes 15 anvils with 4 spacers, and the Neoteck digital includes 12 anvils. The BOBOVAV and the Neoteck dial include 2 measuring rods each, with one rod for small bores and one for large bores. The BOBOVAV and the Neoteck dial also include 3 washers, in 0.02, 0.05 and 0.1 inch, for fine adjustment. Check the anvil sizes against the bores you measure most.

Self-centering heads

Four of the five gauges state self-centering measuring heads, which hold the gauge square in the bore while you read it. Four of the five gauges state two-point contact, which is how they detect ovality and taper, the two wear shapes that matter in a cylinder. The Neoteck dial is the one gauge here that does not state self-centering heads, so it leans more on the hand holding it steady.

Use as directed. Zero the indicator before each round of measurements, keep the contacts clean, and store the gauge in its case when the job is done. A reading is only as good as the zero setting behind it.

Before You Strike an Arc

  • Zero the indicator and pick the anvil that matches the bore before you measure.
  • Check the case on arrival: 23 anvils, 2 rods and 3 washers in the sets that list them.
  • Keep the measuring head clean and the gauge in its case between jobs.
  • Confirm the depth figure against the cylinder you plan to measure, 5.9 or 6 inches here.

FAQ for welders

How do you use a bore gauge?

Set the zero on the indicator first, then pick the measuring head and anvil that match the bore size. Slide the gauge into the bore and let the self-centering head settle it in place. Read the indicator to see the bore size, and move the gauge along the bore to check for taper and ovality.

How do you use a digital bore gauge?

Zero the digital indicator before measuring, then select the measuring head of the right size for the bore. The digital indicator shows the reading on its display, with a resolution of 0.0005 inch on the two digital gauges here. Work through the bore in steps to check the size at more than one depth.

How do you use a cylinder bore gauge?

Use it to check a cylinder bore for wear, taper and out-of-round shape. The two-point contact system detects those shapes as you move the gauge down the bore. The gauges here reach 5.9 or 6 inches deep, which covers the cylinders they are made for.

How do you set a bore gauge?

Adjust the pointer of the indicator to the zero setting before you measure, and select the measuring head of the right size for the bore. The Accusize adds a bezel lock that holds the zero setting once you set it. Recheck the zero if you swap anvils.

How do you use a dial bore gauge?

Zero the dial indicator, pick the anvil that fits the bore, and read the needle against the dial face. The Neoteck dial reads on a dial of 0 to 0.25 inch, and the Accusize reads on a dial of 0 to 0.05 inch with 0.0001 inch graduations. Read the needle against the dial face and note the reading before you move the gauge.

Related: measuring and layout hub, precision measuring hub, best dial bore gauge for engine building, micrometer vs caliper, dial indicator setup, how to use digital calipers, and best digital caliper under 100.

More buying guides