Best Electric Hoist Trolley (2026): 5 Picks for Strut Channel and I-Beam
Five electric hoist trolleys for strut channel and I-beam, compared on load rating, wheel count, beam fit and build, from what each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallLookFox 6+2 Wheel9.5/10View on Amazon - 2
Best I-Beam PickPOWLAB 1 Ton I-Beam9.5/10View on Amazon - 3
Best Strut Channel PickAYEKILI 6 Wheel9.5/10View on Amazon - 4
Best PA Series FitVEVOR 1 Ton Manual9.5/10View on Amazon
A heavy engine block, a steel beam or a loaded pallet does not move itself across a shop. An electric hoist lifts it, and the trolley is the part that carries the hoist along the rail, so a weak trolley turns a good hoist into a stuck load. This guide to the best electric hoist trolley for a garage or shop compares five picks for strut channel and I-beam, scored on what each listing states: load rating, wheel count, beam fit and build.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall LookFox 6+2 Wheel: A stated 3000 lb safe load and 9000 lb breaking strength, 8 wheels on a solid steel bracket, and the only 2 pack here with channel end caps. Check price on Amazon
- Best I-Beam Pick POWLAB 1 Ton I-Beam: A stated 2205 lb working load, width adjustment from 1.96 to 6.69 inches, sealed bearings and bumper guards. Check price on Amazon
- Best Strut Channel Pick AYEKILI 6 Wheel: A stated 2880 lb safety load and 6613 lb breaking strength, 6 wheels, and a 2 pack for a two direction setup. Check price on Amazon
- Best PA Series Fit VEVOR 1 Ton Manual: A stated 2200 lb load on Q235 carbon steel, cast steel wheels and a 2.68 to 4.33 inch width adjustment for PA600 to PA1000 hoists. Check price on Amazon
The machines

LookFox 6+2 Wheel Hoist Trolley
An 8 wheel strut channel trolley with a stated 3000 lb safe load and 9000 lb breaking strength, sold as a 2 pack with end caps.
Pros
- Stated 3000 lb safe load and 9000 lb breaking strength, the highest here
- 8 wheels on a solid steel bracket with an anti lock and anti fall design
- Fits all 1-5/8 inch wide or taller strut channel
- Sold as a 2 pack with 4 end caps for the channel
Cons
- Strut channel only, it does not fit an I-beam
- No warranty term in the listing
- No stated item weight, so the heft is unknown before ordering
- A 2 pack suits a two rail setup, so a single trolley buyer pays for a spare

POWLAB 1 Ton I-Beam Hoist Trolley
A 1 ton push trolley for I-beam and H-beam, with a stated 2205 lb working load, width adjustment from 1.96 to 6.69 inches and sealed bearings.
Pros
- Stated 2205 lb working load, the highest of the I-beam trolleys here
- Width adjusts from 1.96 to 6.69 inches with spacer washers
- Sealed lubricated ball bearings and dual wheels for smooth push travel
- Anti loose locknuts and bumper guards on a powder coated alloy steel frame
Cons
- Manual push only, it does not drive itself along the beam
- No warranty term in the listing
- Beam fit is stated as 2.68 to 4.33 inches, so measure the flange before ordering
- At 23.15 lb it is the heaviest trolley here

AYEKILI Hoist Trolley for PA200-1000 Electric
A 6 wheel strut channel trolley for PA200-1000 electric hoists, with a stated 2880 lb safety load and 6613 lb breaking strength, sold as a 2 pack.
Pros
- Stated 2880 lb safety load and 6613 lb breaking strength
- Made for PA200-1000 electric hoists, a wide fit range
- 6 wheels for smooth travel in two directions on strut channel
- Sold as a 2 pack for a two direction or two rail setup
Cons
- Strut channel only, it does not fit an I-beam
- No warranty term in the listing
- Fixing screws inside the channel block the trolley, so the channel bolts must sit outside the track
- No stated finish or coating for rust protection

VEVOR Electric Hoist Manual Trolley
A manual push trolley for I-beam and H-beam, with a stated 2200 lb load on a Q235 carbon steel body and cast steel wheels.
Pros
- Stated 2200 lb load, 998 kg, on a high strength Q235 carbon steel body
- Width adjusts from 2.68 to 4.33 inches with spacers or sleeves
- Large diameter cast steel wheels with precision bearings
- Made for PA600, PA700, PA800, PA900 and PA1000 electric hoists
Cons
- Manual push only, it does not drive itself along the beam
- No warranty term in the listing
- Narrower width range than the POWLAB, 2.68 to 4.33 inches against 1.96 to 6.69 inches
- At 22.71 lb it adds noticeable weight to the beam before the load

SKTREX 6 Wheel Hoist Trolley with Rollers
A 6 wheel strut channel trolley with a stated 6613 lb break strength and a design load that runs from 380 lb at 600 rpm to 980 lb at 100 rpm, sold as a 2 pack.
Pros
- Stated 6613 lb break strength with a solid steel intermediate support
- Galvanized zinc coating for rust protection
- Fits 1-5/8 inch wide and taller strut channel
- Sold as a 2 pack with two way movement installation
Cons
- Design load falls to 380 lb at 600 rpm, the lowest stated load here
- No warranty term in the listing
- Strut channel only, it does not fit an I-beam
- The design load depends on speed, so the buyer must match the rpm to the load
Other welders and gear to compare
3 Ton Gantry Crane MAX6600LBSCheck price on Amazon
Takywep Adjustable Height Shop Crane Hoist with TrolleyCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Load rating | Wheels | Beam / channel fit | Type | Warranty |
|---|---|---|---|---|---|---|
| LookFox 6+2 Wheel | 9.5/10 | 3000 lb safe, 9000 lb break | 8 | 1-5/8 in strut channel and taller | Strut channel, 2 pack | None stated |
| POWLAB 1 Ton I-Beam | 9.5/10 | 2205 lb working load | Dual | 1.96 to 6.69 in adjustable | I-beam, push | None stated |
| AYEKILI 6 Wheel | 9.5/10 | 2880 lb safety, 6613 lb break | 6 | 1-5/8 in strut channel and taller | Strut channel, 2 pack | None stated |
| VEVOR 1 Ton Manual | 9.5/10 | 2200 lb | Dual | 2.68 to 4.33 in I-beam | I-beam, push | None stated |
| SKTREX 6 Wheel | 9.4/10 | 380 to 980 lb by speed, 6613 lb break | 6 | 1-5/8 in strut channel and taller | Strut channel, 2 pack | None stated |
All specs here repeat what the maker rates and the listing prints, copied down 19 November 2026.
How to pick the best electric hoist trolley
Load rating and break strength
Start with the load you will actually lift, then read the rating the maker states for that trolley. Two of the strut channel trolleys state safe or safety loads of 2880 and 3000 lb, with break strengths of 6613 and 9000 lb, while the I-beam trolleys state working loads of 2200 and 2205 lb. The SKTREX is the odd one: its design load changes with speed, from 380 lb at 600 rpm to 980 lb at 100 rpm, so match the speed to the load before you buy. Never exceed the rated capacity, and never lift a load over people.
Strut channel or I-beam
The rail decides the trolley. Three picks here fit 1-5/8 inch wide or taller strut channel and nothing else, while the POWLAB and the VEVOR fit I-beam and H-beam. A strut channel trolley will not ride an I-beam flange, and an I-beam trolley will not ride strut channel, so check the rail first and the trolley second.
Wheels and bearings
Wheels carry the load sideways, so count them and read what they run on. The LookFox runs on 8 wheels, the AYEKILI and the SKTREX on 6 wheels each, and the I-beam trolleys on dual wheels. The POWLAB states double sealed lubricated ball bearings, the VEVOR states precision bearings with large diameter cast steel wheels, and the strut channel trolleys state no bearing type at all. Sealed bearings matter in a dusty shop, where grit works into open races.
Width adjustment
Beam flanges vary, so a trolley that adjusts fits more shops. The POWLAB adjusts from 1.96 to 6.69 inches with spacer washers, and the VEVOR adjusts from 2.68 to 4.33 inches, 68 to 110 mm, with spacers or sleeves. The strut channel trolleys do not adjust; they fit 1-5/8 inch wide or taller channel as it comes. Measure the flange or the channel before ordering, and keep the spacer washers with the trolley so the next adjustment is a short job.
Two pack or single
Three of the five trolleys here come as a 2 pack, which suits a two rail setup or a spare on the shelf. A single trolley buyer pays for a second trolley either way, so weigh the spare against buying one later. The LookFox 2 pack also brings 4 end caps for the channel, a small extra that finishes the rail ends.
Use as directed. Never exceed the rated capacity of the trolley or the hoist, and never lift a load over people. Keep the load from swinging, keep hands clear of the wheels and the channel while the trolley rolls, and check the wheels, locknuts and beam fit before each lift. Store the trolley dry and keep the track clear of spatter and grit.
Before You Strike an Arc
- Check the rail size against the trolley fit before mounting: 1-5/8 inch strut channel for the channel trolleys, and a measured flange width for the I-beam trolleys.
- Mount the hoist to the trolley and check the locknuts and bumper guards before the first lift.
- Keep channel bolts outside the track so the trolley can pass; bolts inside the channel block the run.
- Roll the trolley along the full run empty first, and check that the wheels stay on the rail at both ends.
- Wear eye protection and gloves when handling steel channel and beam, and keep the area below the load clear.
For more options, see our lifting pressing guides.
FAQ for welders
How do I use an electric hoist with a trolley?
Mount the hoist to the trolley, set the trolley on the beam or channel, and roll it to a spot above the load. Hook the load, lift it clear, then push the trolley along the rail to move the load sideways. Lower the load, unhook it, and roll the trolley back before the next lift.
How does an electric hoist work?
A motor winds the rope or chain to raise the hook and unwinds it to lower the hook, while the trolley carries the hoist along the rail so the load can move sideways as well as up and down. The hoist hangs from the trolley, and the trolley rolls on the beam or channel under the weight.
How much does an electric hoist cost?
The cost depends on the capacity, the brand and the features, so there is no single figure that covers every hoist. A small hoist for light garage work costs less than a 1 ton hoist for daily shop use. Check the current price on the hoist that matches the load, and match the trolley to the same hoist series.
What size strut channel fits these trolleys?
Three trolleys here fit all 1-5/8 inch wide or taller strut channel: the LookFox, the AYEKILI and the SKTREX. That size is the common channel in garage and shop hoist setups. Measure the channel before ordering, since a narrower channel will not hold the trolley.
Can I use a strut channel trolley on an I-beam?
No. A strut channel trolley rides inside the channel, and an I-beam trolley rides on the beam flange, so the two do not swap. For an I-beam, pick the POWLAB or the VEVOR, which state a fit for I-beam and H-beam. For strut channel, pick one of the three channel trolleys.
Related: best portable electric hoist, manual chain hoist, electric hoist vs chain hoist, electric hoist vs come along, best lever chain hoist, parts of a chain hoist, and the best gantry crane large. Also see our types of lifting clamps.
Scoring, line by line
Each trolley is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. No trolley here states a safety certification, so every trolley scores zero on that criterion, and no trolley here states a warranty term, so warranty scores zero too. The ranking comes from performance, build and value: load ratings against the stated class, steel and bearings, and what each trolley gives for the money.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| LookFox 6+2 Wheel | 9.5 | 32 | 22 | 21 | 0 | 0 |
| POWLAB 1 Ton I-Beam | 9.5 | 30 | 22 | 20 | 0 | 0 |
| AYEKILI 6 Wheel | 9.5 | 29 | 21 | 21 | 0 | 0 |
| VEVOR 1 Ton Manual | 9.5 | 29 | 21 | 20 | 0 | 0 |
| SKTREX 6 Wheel | 9.4 | 27 | 20 | 20 | 0 | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.




