Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Parts of a Chain Hoist: Components and Replacements

The parts of a chain hoist, what each one does, and 4 hoists whose listings state the parts plainly.

Parts of a Chain Hoist: Components and Replacements
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1VEVOR Hand Chain Hoist 3 Ton 6600 lbs LoadVEVOR Hand Chain Hoist 3 Ton 6600 lbs Load9.7/10View on Amazon
  2. 2BIG RED Hand Chain Hoist 1 Ton 2200 Lbs Capacity 8BIG RED Hand Chain Hoist 1 Ton 2200 Lbs Capacity 89.6/10View on Amazon
  3. 3VEVOR Manual Lever Chain HoistVEVOR Manual Lever Chain Hoist9.6/10View on Amazon
  4. 4SPECSTAR Hand Chain Hoist 1 Ton 2200 Lbs CapacitySPECSTAR Hand Chain Hoist 1 Ton 2200 Lbs Capacity9.6/10View on Amazon

A load hangs in the air over a bench, and the hoist above it is doing quiet work. Every pull on the hand chain moves through a small set of parts, and knowing the parts of a chain hoist tells you which piece to check when the load slips, the chain binds, or a hook will not seat. This guide names each part, explains what it does, and shows hoists whose listings state the parts plainly.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

VEVOR Hand Chain Hoist 3 Ton 6600 lbs Load

VEVOR Hand Chain Hoist 3 Ton 6600 lbs Load

VEVOR9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 ton hand chain hoist with a 6600 lb capacity, a 10 ft lift height, G80 galvanized chain and a dual pawl brake.

Pros

  • 6600 lb capacity covers heavy garage and warehouse lifts
  • G80 heat-treated chain resists corrosion and breakage, per the maker
  • Dual pawl brake holds the load stable at height
  • Both hooks rotate 360° for flexible positioning

Cons

  • 41.67 lb weight is the heaviest here
  • Needs 390N of pull force at full load
  • 10 ft lift height is the limit for a single setup
  • 3 ton rating is more hoist than a light garage job needs
BIG RED Hand Chain Hoist 1 Ton 2200 Lbs Capacity 8

BIG RED Hand Chain Hoist 1 Ton 2200 Lbs Capacity 8

BIG RED9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 ton hand chain hoist with a 2200 lb capacity, an 8 ft lift height, a 1/4 inch 20Mn2 alloy steel chain and a limited 1 year manufacturer warranty.

Pros

  • Limited 1 year manufacturer warranty, the only stated term here
  • Meets ASME B30.16 overhead hoist safety standards
  • 1/4 inch 20Mn2 alloy steel chain with a black oxide finish
  • Hooks with a safety latch clasp rotate a full 360 degrees

Cons

  • 8 ft lift height is the shortest here
  • 1 ton capacity is less than the 3 ton and 1-1/2 ton hoists here
  • No stated item weight or dimensions in the listing
  • 1/4 inch chain suits the 1 ton rating; heavier loads need a larger hoist
VEVOR Manual Lever Chain Hoist

VEVOR Manual Lever Chain Hoist

VEVOR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1-1/2 ton lever chain hoist with a 3300 lb capacity, a 10 ft length, G80 galvanized chain and a Weston double-pawl brake.

Pros

  • 3300 lb capacity, more than the 1 ton hoists here
  • G80 galvanized manganese steel chain resists corrosion
  • Weston dual-pawl brake spreads the load across the gears
  • Guided chain leading device keeps the chain from jamming

Cons

  • 26.0 lb weight is heavier than the 16.9 lb SPECSTAR
  • No warranty term is stated
  • 20.3 inch body is the longest here, so it needs more room to work the lever
  • 1-1/2 ton capacity is less than the 3 ton hoist here
SPECSTAR Hand Chain Hoist 1 Ton 2200 Lbs Capacity

SPECSTAR Hand Chain Hoist 1 Ton 2200 Lbs Capacity

SPECSTAR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 ton hand chain hoist with a 2200 lb rated load, a 10 ft chain, an 8.5 ft effective lift height and a mechanical load brake built to ASME B30.16.

Pros

  • 2 forged steel hooks rotate 360° to lock the load
  • Built to meet ASME B30.16 overhead hoist standards
  • Pre-lubricated ball bearings cut the effort of each pull
  • 16.9 lb weight is the lightest here

Cons

  • No warranty term is stated
  • 8.5 ft effective lift height is shorter than the 10 ft chain
  • 1 ton rated load is less than the 3 ton and 1-1/2 ton hoists here
  • Low-headroom design suits confined spaces rather than tall open lifts

Parts of a chain hoist in one paragraph

A hand chain hoist has 2 chains, a set of gears, a brake, 2 hooks and a housing. The hand chain is the loop you pull. The load chain is the chain that carries the hook and the load. The gears sit between them and turn a light pull into a heavy lift. The brake holds the load where you leave it. The top hook hangs the hoist from a beam, the load hook carries the work, and the housing covers the gears and brake. That is the whole machine, and each part below shows up in the hoists in this guide, except the VEVOR lever hoist, which has a lever in place of the hand chain loop.

Side by side

Hoist Rated capacity Lift height Brake Hook
VEVOR 3 Ton 6600 lbs (3 ton) 10 ft Dual pawl 360° rotating, security lock
BIG RED 1 Ton 2200 lbs (1 ton) 8 ft Mechanical load brake 360° rotating, safety latch clasp
VEVOR Lever 1-1/2 Ton 3300 lbs (1-1/2 ton) 10 ft Weston double-pawl 360° rotating alloy steel
SPECSTAR 1 Ton 2200 lbs (1 ton) 8.5 ft effective Mechanical load brake 360° rotating forged steel

The table above lines up the 4 hoists in this guide by rated capacity, lift height, brake and hook. Capacity is the main filter: the 1 ton hoists suit lighter loads, while the 3 ton VEVOR covers heavier lifts. Lift height is the next filter: the two VEVOR hoists list 10 ft, while the BIG RED lists 8 ft and the SPECSTAR lists 8.5 ft of effective lift from a 10 ft chain.

The parts, one by one

  • Hand chain. The loop you pull to raise and lower the load on a hand chain hoist. The SPECSTAR, the VEVOR 3 ton model and the BIG RED are hand chain hoists; the VEVOR lever hoist has a lever instead of a hand chain loop.
  • Load chain. The chain that carries the load hook. VEVOR fits G80 galvanized manganese steel chain on its lever hoist and heat-treated G80 chain on its 3 ton model, and BIG RED fits 1/4 inch 20Mn2 alloy steel chain with a black oxide finish.
  • Gears. Industrial-grade steel gears on the SPECSTAR turn the pull into lift, and load-sharing gears on the BIG RED spread the work across the gear set.
  • Brake. The mechanical load brake on the SPECSTAR and the BIG RED holds the load and stops slipping. The dual pawl brake on the VEVOR 3 ton model holds the load stable at the height you set, and the Weston double-pawl brake on the VEVOR lever hoist spreads the load to opposite sides of the gears.
  • Hooks. The SPECSTAR, the VEVOR 3 ton model and the BIG RED each list 2 hooks, and each hoist here lists hooks that rotate 360°. The BIG RED hooks (on Amazon) add a safety latch clasp, and the VEVOR 3 ton hooks add a security lock.
  • Housing and cover. The SPECSTAR has a full steel structure with a cold-rolled steel cover that shields the core parts. The VEVOR 3 ton model has a reinforced casing over alloy steel.
  • Bearings. Pre-lubricated ball bearings on the SPECSTAR cut the effort of the pull, and roller ball bearings on the BIG RED cut friction at the rotating parts.

That is the full parts list for the hoists in this guide. When a hoist fails to hold, check the brake. When the chain binds, check the chain guide and the hooks. When the pull feels heavy, check the bearings and the gears.

How the parts work together

On a hand chain hoist, pulling the hand chain turns the gears, the gears move the load chain, and the brake holds the load when you stop pulling. The hooks carry the load at both ends, and the housing keeps grit off the gears and brake. A weak link in any one part shows up as a slipping load, a binding chain, or a hook that will not seat, so check the part that matches the symptom.

Chain hoists that show their parts

The 4 hoists below list their parts plainly, from the chain grade to the brake type, so you can match each part to the job.

What to check before you lift

Hang the hoist from the top hook and seat each hook fully before any lift. Pull the hand chain through its full range with no load and watch the chain run free through the guide. Set a light load, stop pulling, and confirm the brake holds it where you left it. Check each hook for a working latch or lock, and keep the load within the rated capacity the maker lists. Never lift a load over people, and never exceed the rated capacity.

For more options, see our metal fab tools guides.

FAQ for welders

What are the main parts of a chain hoist?

The main parts of a hand chain hoist are the hand chain, the load chain, the gears, the brake, the hooks and the housing. The hand chain is the loop you pull, the load chain carries the load, the gears turn a light pull into a heavy lift, and the brake holds the load where you leave it. The hooks connect the hoist to the beam and to the load, and the housing covers the gears and brake. A lever hoist has a lever in place of the hand chain loop.

What does the load brake do on a chain hoist?

The load brake holds the load at the height you set and stops it from slipping back down. The SPECSTAR and the BIG RED list a mechanical load brake, the VEVOR 3 ton model lists a dual pawl brake, and the VEVOR lever hoist lists a Weston double-pawl brake. Check the brake with a light load before lifting anything heavy.

How much can a 1 ton chain hoist lift?

A 1 ton chain hoist is rated for 2200 lb. The BIG RED lists a 1 ton rating with an 8 ft lift height. Stay within the rated load the maker lists, and never exceed it.

What is G80 chain on a hoist?

G80 is the chain grade VEVOR lists on both of its hoists here: galvanized manganese steel on the lever hoist and heat-treated G80 chain on the 3 ton model. The maker states high strength and toughness, and the galvanized layer resists corrosion in harsh environments. The SPECSTAR lists 20Mn2 forged chain, and the BIG RED lists 1/4 inch 20Mn2 alloy steel chain.

Can a chain hoist lift over people?

No. Never lift a load over people, and never exceed the rated capacity the maker lists. Hang the hoist from a sound support, seat each hook fully, and check the brake with a light load before the real lift.

Related: electric hoist vs chain hoist, lever hoist vs chain hoist, and electric hoist vs come along.

More buying guides

Hoists and Lifting ·

Best Lever Chain Hoist (2026)

5 lever chain hoists for shop and farm work, compared by rated capacity, lift, chain, brake, weight and warranty.