Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill Press for Home Garage: 3 Picks for Metalwork

Three drill presses for a home garage, two WEN benchtops and one VEVOR mag drill, scored on swing, speed, travel and stated warranty.

Best Drill Press for Home Garage: 3 Picks for Metalwork
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1WEN 12-Inch DP1263V12-inch benchtopWEN 12-Inch DP1263V9.5/10View on Amazon
  2. 2WEN 10-Inch DP1062V10-inch benchtopWEN 10-Inch DP1062V9.5/10View on Amazon
  3. 3VEVOR 1550W Magnetic1550W magneticVEVOR 1550W Magnetic9.5/10View on Amazon

A home garage drill press needs to drill steel, not just wood: repeatable holes in plate, brackets and tube, square to the work. The best drill press for home garage metalwork balances swing, speed range and spindle travel against the bench space you have. This guide compares three on what each listing states: two WEN benchtop presses and one VEVOR mag drill.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • 12-inch benchtop WEN 12-Inch DP1263V: 12 inch swing, 3-1/8 inch travel, 580-3100 RPM variable and a stated two-year warranty. Check price on Amazon
  • 10-inch benchtop WEN 10-Inch DP1062V: 57 lb, 530-3100 RPM with readout and two-year warranty, 10 inch swing. Check price on Amazon
  • 1550W magnetic VEVOR 1550W Magnetic: 2922 lbf hold, 2.4 inch coring, M3-M16 tapping, overload shut-off stated. Check price on Amazon

The machines

VEVOR Magnetic Drill Press, 1550 W

VEVOR Magnetic Drill Press, 1550 W

VEVOR9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1550W magnetic drill with 2.4 inch coring capacity, 2922 lbf of magnetic hold, Morse taper and M3-M16 tapping.

Pros

  • 2.4 inch coring diameter, the largest cutting capacity here
  • 2922 lbf magnetic hold, the strongest here
  • Coring, tapping from M3 to M16 and twist drilling in one tool
  • Overload shut-off stated in the bullets

Cons

  • 110 volts at 11.9 amps, so check the circuit before buying
  • No warranty term is stated
  • 49.6 lb and needs flat ferrous steel to hold
  • Twist drilling only from 0.1 to 0.6 in, coring is the real job
WEN 12-Inch Benchtop Drill Press

WEN 12-Inch Benchtop Drill Press

WEN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12 inch benchtop press with a 6.2 amp variable speed motor, 3-1/8 inch spindle travel, a 5/8 inch keyed chuck and a stated two-year warranty.

Pros

  • 12 inch swing, the largest benchtop swing here
  • 3-1/8 inch spindle travel, the longest here
  • Variable speed from 580 to 3100 RPM with a digital readout
  • Two-year warranty plus a class IIIA laser and LED work light

Cons

  • 85 lb in the bullets, the heaviest benchtop here, needs a stout bench
  • No safety certification is stated
WEN 10-Inch Benchtop Drill Press

WEN 10-Inch Benchtop Drill Press

WEN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10 inch benchtop press with a 6.2 amp variable speed motor, 2 inch spindle travel, a 1/2 inch keyed chuck and a stated two-year warranty.

Pros

  • Variable speed from 530 to 3100 RPM with a digital readout
  • 57 lb in the bullets, lighter than the 12 inch WEN
  • 1/2 inch keyed chuck suits common metal drilling bits
  • Two-year warranty stated in the bullets

Cons

  • 2 inch spindle travel vs 3-1/8 inch on the 12 inch WEN
  • 10 inch swing limits wider workpieces
  • No safety certification is stated

Other welders and gear to compare

Spec sheet comparison

Model Score Type Swing / boring Speed Chuck Warranty
WEN 12-Inch DP1263V 9.5/10 Benchtop 12 in swing 580-3100 RPM variable 5/8 in keyed 2 years
WEN 10-Inch DP1062V 9.5/10 Benchtop 10 in swing 530-3100 RPM variable 1/2 in keyed 2 years
VEVOR 1550W Magnetic 9.5/10 Magnetic 2.4 in boring 0-600 RPM adjustable 19 mm max Not stated

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 19 October 2026.

Buying guide: best drill press for home garage

Swing and what it means

Swing is twice the distance from the spindle to the column, and it sets the widest piece you can center under the chuck. The WEN 12 inch gives the most room here, the 10 inch less, and the mag drill does not state a swing at all, since it clamps to the work differently. For brackets and plate wider than a hand, the bigger swing earns its bench space.

Speed range

Metal wants slower speeds than wood, and variable speed lets you match the bit to the job. Both WENs state mechanical variable speed, 580 to 3100 RPM on the 12 inch and 530 to 3100 RPM on the 10 inch, each with a digital readout. The 1550W VEVOR states 0 to 600 RPM adjustable.

Spindle travel

Travel is how deep the quill moves in one pull. The WEN 12 inch states 3-1/8 inches, the longest here, against 2 inches on the WEN 10 inch. Deeper travel means fewer repositioning moves on thick stock.

Benchtop vs mag drill

A benchtop press lives on the bench and drills anything you can lay on the table. A mag drill clamps itself to ferrous steel with its magnet, 2922 lbf on the 1550W, and drills where the steel sits: beams, plate, frames. It needs clean flat steel to hold; it will not stick to aluminum or rusty scale. Pick the benchtop for general garage work, the mag drill for steel fabrication on the job.

Chuck capacity

The WEN 12 inch states a 5/8 inch keyed chuck, the WEN 10 inch a 1/2 inch keyed chuck, both with onboard key storage. The 1550W VEVOR states a 19 mm maximum chuck with a Morse taper spindle. Match the chuck to the bits you own.

Warranty in writing

Two listings state a warranty term: two years on both WENs. The VEVOR mag drill states no warranty term. A stated term is the only promise that counts; everything else is the listing’s word.

Use as directed. Bolt or clamp the press to a stable bench before drilling steel; an 85 lb press walking across the bench is a hazard. Keep the chuck key out of the chuck before starting the motor, wear eye protection, and clamp the work, never hold it by hand. Mag drills must sit on clean flat steel before you switch the magnet on.

Before You Strike an Arc

  • Check the outlet first: the VEVOR mag drill states 110 volts, both WENs state 120 volts. Confirm the circuit matches the listing before you plug in.
  • Mag drills need ferrous steel to hold: the listing states 2922 lbf of magnetic force. Verify the work is flat, clean steel before switching the magnet on.
  • Both WENs ship the chuck key with onboard storage and an adjustable depth stop. Confirm both arrived and re-zero the stop before the first hole.
  • Unclamp the quill and check the speed setting on arrival, and confirm the laser and light on the WEN 12 inch power up.

FAQ for welders

What size drill press do I need for a home garage?

For general metalwork, a 10 to 12 inch benchtop swing covers brackets, plate and tube. The WEN 12 inch here gives the most room and the longest travel; the 10 inch suits a smaller bench. If the work is structural steel that cannot come to the bench, a mag drill goes to the work instead.

Can a benchtop drill press drill steel?

Yes, at the right speed with the right bit and the work clamped. Both WENs state variable speed down to 530 to 580 RPM, which suits larger bits in steel. Keep the speed low, use cutting fluid, and never hold the work by hand.

What is a mag drill good for in a home shop?

A mag drill cores and drills holes in steel beams, plate and frames where the magnet can bite. The 1550W VEVOR here states 2.4 inch coring and M3 to M16 tapping. It needs flat ferrous steel; it will not hold on aluminum, stainless or rusty scale.

Do I need variable speed?

It helps a lot on metal. The two WENs state mechanical variable speed with a digital readout, so you can slow down for big bits and speed up for small ones.

What chuck size should I get?

A 1/2 inch chuck covers most garage metal drilling; the WEN 10 inch states exactly that. The WEN 12 inch states 5/8 inch for larger bits. The mag drill here uses its own shank: Morse taper on the 1550W.

Related: best drill press for metalworking, drill press vs mill, magnetic drill vs benchtop drill press, best drill press vise and the metal fab tools hub.

Scoring, line by line

Each press is scored on performance, build, value, safety and warranty. Only the VEVOR mag drill states a safety feature, the overload shut-off, so only it scores above zero on that criterion; no listing here states a safety certification.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
VEVOR 1550W Magnetic 9.5 29 20 20 4 0
WEN 12-Inch DP1263V 9.5 32 21 21 0 0
WEN 10-Inch DP1062V 9.5 29 21 21 0 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.

More buying guides

Welding Safety Gear ·

How to Set Up a Welding Area in a Home Garage

How to set up a safe, organized welding space in a home garage, covering concrete floor prep, electrical supply, spark containment, ventilation, and fire…