Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Cross Slide Bench Vise (2026)

Five cross slide vises for drill presses and mills, compared on jaw width, travel, build and the warranty each listing states.

Best Cross Slide Bench Vise (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Wilton CS6Best OverallWilton CS69.7/10View on Amazon
  2. 2WEN CV413Best TravelWEN CV4139.6/10View on Amazon
  3. 3findmall 4 InchBest 4-Inch Visefindmall 4 Inch9.5/10View on Amazon
  4. 4HFS 3 InchBest SwivelHFS 3 Inch9.5/10View on Amazon
  5. 5BACHIN RotaryBest Rotary TableBACHIN Rotary9.4/10View on Amazon

A cross slide vise moves the work under the drill, so a hole lands where the layout says it should. This guide compares the best cross slide bench vise picks for drill presses and mills, on what each listing states: jaw width, travel, build and warranty.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Wilton CS6: The widest jaw here at 6 inches, hardened V-grooved jaws, five bolt lugs and the only stated lifetime warranty. Check price on Amazon
  • Best Travel WEN CV413: Jaws travel 5.8 inches left and right and 6 inches front and back, with 0.1 mm hand wheel increments. Check price on Amazon
  • Best 4-Inch Vise findmall 4 Inch: A 3.94 inch jaw width with 3.54 inch maximum clamping, in cast iron, on a 141 by 235 mm base. Check price on Amazon
  • Best Swivel HFS 3 Inch: A swiveling 3 inch vise in ductile iron rated 80000 PSI, with double screw rods and adjustable gibs. Check price on Amazon
  • Best Rotary Table BACHIN Rotary: A 90 degree rotary table with X 80 mm and Y 67 mm adjustment and a removable silicone pad. Check price on Amazon

The machines

Wilton Cross-Slide Drill Press Vise

Wilton Cross-Slide Drill Press Vise

Wilton9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6 inch cross slide vise with hardened V-grooved jaws, five bolt lugs and a lifetime warranty against manufacturing defects.

Pros

  • Widest jaw here at 6 inches, with a 6 inch maximum opening, per the title and bullets
  • Hardened V-grooved jaws hold round-shaped objects both vertically and horizontally
  • Five bolt lugs for mounting on a machine table, per the listing
  • Lifetime warranty against manufacturing defects, the only stated warranty here

Cons

  • No travel figure is stated in the title or bullets
  • Only one size is listed
WEN Cross Vise, 3.25-Inch with Compound Slide

WEN Cross Vise, 3.25-Inch with Compound Slide

WEN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3.25 inch cross slide vise in powder-coated cast iron, with jaws that travel 5.8 inches left and right and 6 inches front and back.

Pros

  • Jaws travel 5.8 inches left and right and 6 inches front and back
  • Hand wheels with machine-marked 0.1 mm increments for precise positioning
  • Industrial-strength powder-coated cast iron construction, per the listing
  • Universal design compatible with the majority of drill presses on the market, per the listing

Cons

  • No warranty term is stated
  • Jaw width of 3.25 inches suits smaller work than a wider vise
  • No mounting slot or bolt lug count is stated
  • Only one size is listed
findmall 4 Inch Cross Slide Drill Press Vise Heavy

findmall 4 Inch Cross Slide Drill Press Vise Heavy

findmall9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4 inch cross slide vise in cast iron, with a 3.94 inch jaw width, 3.54 inch maximum clamping and a 141 by 235 mm base.

Pros

  • Jaw width of 3.94 inches with maximum clamping of 3.54 inches, per the listing
  • Cast iron construction with strong toughness and high accuracy, per the listing
  • Two handles move the vise back and forth, left and right, with a clear scale
  • Jaws have high friction and strong clamping force, per the listing

Cons

  • No warranty term is stated
  • No travel distance is stated
  • No rotary table is stated
  • Only one size is listed
HFS(R) 3" Cross Slide Vise Drill Press Metal

HFS(R) 3" Cross Slide Vise Drill Press Metal

HFS9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 inch swiveling cross slide vise in ductile iron rated 80000 PSI, with double screw rods and adjustable gibs.

Pros

  • Ductile iron rated 80000 PSI for minimum bending, per the listing
  • Swiveling vise with perfectly aligned precision jaws for milling work
  • Double screw rods for longitudinal and cross travel
  • Adjustable gibs, per the listing

Cons

  • No warranty term is stated
  • No travel distance is stated
  • No maximum jaw opening is stated
  • Only one size is listed
Rotary Table 90 ° 3" Cross Slide Drill Press Vise

Rotary Table 90 ° 3" Cross Slide Drill Press Vise

BACHIN9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 inch cross slide vise on a 90 degree rotary table, with X 80 mm and Y 67 mm adjustment, a silicone pad and two rotatable handles.

Pros

  • Rotary table turns 90 degrees for angled work
  • X adjustment of 80 mm and Y adjustment of 67 mm, per the listing
  • Removable silicone pad protects the workpiece during operation
  • Two rotatable handles adjust the vise front and back

Cons

  • No warranty term is stated
  • Aluminum alloy body, where the other vises here use cast iron or ductile iron
  • Jaw width of 75 mm suits smaller workpieces
  • Only one size is listed

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Jaw width Max opening Travel Material Warranty
Wilton CS6 9.7/10 6 in 6 in 4-9/10 in X and Y Cast iron, hardened steel Lifetime
WEN CV413 9.6/10 3.25 in 3.25 in 5.8 in left/right, 6 in front/back Powder-coated cast iron Not stated
findmall 4 Inch 9.5/10 3.94 in 3.54 in Not stated Cast iron Not stated
HFS 3 Inch 9.5/10 3 in Not stated Not stated Ductile iron Not stated
BACHIN Rotary 9.4/10 75 mm 77 mm X 80 mm, Y 67 mm Aluminum alloy Not stated

All specs here repeat what the maker rates and the listing prints, copied down 25 October 2026.

Best cross slide bench vise: what the listings show

Jaw width runs from 3 inches to 6 inches across the five vises.

The WEN jaws travel 5.8 inches left and right and 6 inches front and back.

Only the Wilton states a warranty, a lifetime warranty against manufacturing defects.

Buying guide: what matters in a cross slide vise

Jaw width

Jaw width sets the widest workpiece the vise holds. The Wilton jaw is 6 inches wide, with a 6 inch maximum opening. The findmall jaw is 3.94 inches wide, with maximum clamping of 3.54 inches. The WEN jaws are 3.25 inches wide and open up to 3.25 inches. The HFS jaw is 3 inches wide. The BACHIN jaw is 75 mm wide, with a 77 mm opening. Match the jaw to the work you clamp most.

Travel

Travel decides how far the work moves without re-clamping. The WEN jaws travel 5.8 inches left and right and 6 inches front and back. The BACHIN adjusts 80 mm in X and 67 mm in Y. The Wilton spec table lists 4-9/10 inch travel in X and Y. The HFS and findmall listings state no travel figures.

Jaws and round work

The Wilton has hardened V-grooved jaws that hold round-shaped objects both vertically and horizontally, per the listing. The BACHIN gripper carries a removable silicone pad that protects the workpiece during operation. The findmall jaws have high friction and strong clamping force, per the listing, and the workpiece is not easy to shake.

Mounting

A cross slide vise bolts to the machine table. The Wilton base has five bolt lugs for mounting on a machine table. The findmall base has a mounting slot 0.41 inch wide. The BACHIN has a bolt fixing slot. Check the slot or lug spacing against the table before you buy.

Rotary table

The BACHIN worktable turns 90 degrees, with a ring value of 1.5 mm. That suits angled drilling and milling on a drill press. The other vises here have no rotary table stated.

Use as directed. Bolt the vise to the machine table before you drill, keep hands clear of the jaws while the hand wheels turn, and check that the workpiece is clamped before the bit touches it.

Before You Strike an Arc

  • Check the jaw opening against the workpiece: the Wilton opens to 6 inches, the findmall clamps to 3.54 inches and the BACHIN opens to 77 mm.
  • Check the mounting: the Wilton base has five bolt lugs, and the findmall base has a mounting slot 0.41 inch wide.
  • Check the travel against the drill press table: the WEN moves 5.8 inches left and right and 6 inches front and back.
  • Check the rotary table on the BACHIN: it turns 90 degrees, with X 80 mm and Y 67 mm adjustment.

FAQ for welders

What is the best bench vise?

The best bench vise for a drill press is the one whose jaw width, travel and mounting fit the work. The Wilton has the widest jaw here at 6 inches. The WEN states 5.8 inches of travel left and right and 6 inches front and back. Pick by the work, not by the brand.

What size bolts for bench vise?

No listing here states a bolt size. The Wilton base has five bolt lugs for mounting on a machine table. The findmall base has a mounting slot 0.41 inch wide. Measure the lugs or the slot on the vise you buy, and match the bolt to the machine table.

Is bench vise a tool?

Yes. A bench vise is a workholding tool, and a cross slide vise is a drill press vise that moves the work in X and Y under the bit. The vises here mount on drill presses, mills and other mechanical equipment, per the listings.

How to use a vise without a bench?

A cross slide vise does not need a bench: it bolts to the machine table of a drill press or a mill. The Wilton base has five bolt lugs for mounting on a machine table. The BACHIN vise can be used with a drill stand and bench drill, per the listing.

How to set up bench vise?

Bolt the vise to the machine table through the bolt lugs or the mounting slot, then check that the jaws open and close and the hand wheels turn freely. The HFS vise has adjustable gibs for the longitudinal and cross travel, per the listing.

Related: welding tables and carts, best welding vise for table, best welding vise for home shop, best bench vise for metal work and best 6 bench vise.

Scoring, line by line

Each vise is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. Cross slide vises have no electrical safety listing to state, so every vise here scores nothing on that criterion; the ranking comes from the other criteria.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Wilton CS6 9.7 29 21 19 n/a 5
WEN CV413 9.6 30 21 20 n/a 0
findmall 4 Inch 9.5 28 20 19 n/a 0
HFS 3 Inch 9.5 27 21 18 n/a 0
BACHIN Rotary 9.4 26 18 18 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides